1996 TOYOTA LAND CRUISER Electrical

BE−96
−
BODY ELECTRICAL CLOCK
1234
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CH0EO−02
CH0712
BlueRed
White
Charging
Necessary
OK
Add Distilled
Water
CH−2
−
CHARGING CHARGING SYSTEM
1996 LAND CRUISER (RM451U)
CHARGING SYSTEM
ON−VEHICLE INSPECTION
1. CHECK BATTERY ELECTROLYTE LEVEL AND VOLT-
AGE
(a) Check the electrolyte quantity of each cell.
If under the lower level, replace the battery (or add distilled wa-
ter if possible). check the charging system.
(b) Measure the battery voltage between the negative ( −)
and positive (+) terminals of the battery.
Standard voltage: At 20° C (68°F): 12.7 − 12.9 V
HINT:
Before measuring the voltage, turn the ignition switch
OFF and turn off the electrical systems (headlight, blower
motor, rear defogger etc.).
If the vehicle has been running, wait 20 minutes or more
after the vehicle stops before measuring the battery volt-
age.
If the voltage is less than specification, charge the battery.
HINT:
Check the indicator as shown in the illustration.
2. CHECK BATTERY TERMINALS, FUSIBLE LINK AND FUSES
(a) Check that the battery terminals are not loose or cor-
roded.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07312
DI−142
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
9. MANUAL SHIFTING TEST
The purpose of this manual shifting test is to determine whether
a problem is caused by either mechanical or electrical factors.
Disconnecting the solenoid wire disables electrically −con-
trolled automatic gear shifting. In this case, operating the shift
lever is the only way to shift the transmission gear. If the gear
is not changed by shift lever operation, it is assumed that there
is a mechanical problem.
(a) Turn the ignition switch OFF.
(b) Disconnect the solenoid wire connector.
(c) Warm up the engine.
(d) Drive the vehicle.
(e) Check the transmission operation when the shift lever is moved into L, 2 and D positions.
Standard:
Shift LeverOperation
L to 2Shift up
2 to DShift up
D to 2Shift down
2 to LShift down
(f) Turn the ignition switch OFF.
(g) Connect the solenoid wire connector.
(h) Clear DTCs.
HINT:
When the solenoid wire is disconnected, the transmission gear
will be set as listed below:
Shift LeverGear
PParking
RReverse
NNeutral
DO/D (4th)
23rd
L1st
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KB−03
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−143
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the circuit listed for that code i\
n the table below and pro-
ceed to the page given.
DTC No.
(See page)Detection ItemTrouble AreaMIL*Memory
P0500
( DI−153 )Vehicle Speed Sensor Malfunc-
tion
(No. 1 Vehicle Speed Sensor)Open or short in No. 1 vehicle speed sensor circuit
 No. 1 vehicle speed sensor
 ECM

P0710
( DI−154 )Transmission Fluid Temperature
Sensor Malfunction
(ATF Temperature Sensor) Open or short in ATF temperature sensor circuit
 ATF temperature sensor
 ECM

P0750
( DI−156 )Shift Solenoid A Malfunction
(Shift Solenoid Valve No. 1)Shift solenoid valve No. 1 is stuck open or closed
 Valve body is blocked up or stuck
P0753
( DI−157 )Shift Solenoid A Electrical
Malfunction
(Shift Solenoid Valve No. 1)Open or short in shift solenoid valve No. 1 circuit
 Shift solenoid valve No. 1
 ECM

P0755
( DI−156 )Shift Solenoid B Malfunction
(Shift Solenoid Valve No. 2)Shift solenoid valve No. 2 is stuck open or closed
 Valve body is blocked up or stuck
P0758
( DI−157 )Shift Solenoid B Electrical
Malfunction
(Shift Solenoid Valve No. 2)Open or short in shift solenoid valve No. 2 circuit
 Shift solenoid valve No. 2
 ECM

P0770
( DI−161 )Shift Solenoid E Malfunction
(Shift Solenoid Valve SL)Shift solenoid valve SL is stuck open or closed
 Valve body is blocked up or stuck
 Lock− up clutch

P0773
( DI−163 )Shift Solenoid E Electrical
Malfunction
(Shift Solenoid Valve SL)Open or short in shift solenoid valve SL circuit
 Shift solenoid valve SL
 ECM

P1700
( DI−166 ) Speed Sensor No. 2 Circuit
Malfunction
(No. 2 Vehicle Speed Sensor)Open or short in No. 2 vehicle speed sensor circuit
 No. 2 vehicle speed sensor
 ECM

P1780
( DI−169 )Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
 Park/neutral position switch
 ECM

*:  ...MIL light up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Position
NORMALSHIFT SOLENOID NO. 1
MALFUNCTIONING
Solenoid valve
No. 1 No. 2GearSHIFT SOLENOID NO. 2
MALFUNCTIONING
BOTH SOLENOIDS MAL-
FUNCTIONINGSolenoid valve
No. 1 No. 2 GearSolenoid valve
No. 1 No. 2 GearGear when shift selector is
manually operated
D
2
LON
ON
OFF
ON
ON
OFF
OFF OFF
ON
ON OFF
ON
ON
OFF
ON
ON ON OFF 1st
2nd
3rd
O/D
1st
2nd
3rd
1st
2nd X
X
X
X
X
X
X
X
X
ON
ON
OFF
OFF ON
ON
ON
3rd 3rd
O/D
3rd
3rd
1st
2nd X
X
X
X
X
X
X
X
XOFF
OFF
ON
ON OFF OFF
OFF
ON
ON
1st
O/D
3rd 1st O/D O/D
3rd
1st
1st
O/D O/D O/D
O/D
3rd 3rd
3rd
1st
1st
X: Malfunctions ON
ON
3rd
3rd
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−157
1996 LAND CRUISER (RM451U)
DTC P0753, P0758 Shift Solenoid A/B Electrical Malfunc-
tion (Shift Solenoid Valve No. 1/No. 2)
CIRCUIT DESCRIPTION
Shifting from 1st to O/D is done in combination with ON and OFF of the shift solenoid valves No. 1 and No\
.
2 controlled by ECM. If an open or short circuit occurs in either of the \
shift solenoid valves, the ECM controls
the remaining normal shift solenoid valve to allow the vehicle to be operat\
ed smoothly (Fail safe function).
Fail Safe Function:
If either of the shift solenoid valve circuits develops an open or short, \
the ECM turns the other shift solenoid
ON and OFF to shift to the gear positions shown in the table below. The ECM also turns the shift solenoid
valve SL OFF at the same time. If both solenoids are malfunction, hydraulic contr\
ol cannot be done electroni-
cally and must be done manually.
Manual shifting as shown in the following table must be done (In the case of a short circuit, the E\
CM stops
sending current to the short circuited solenoid).
HINT:
Check the shift solenoid valve No. 1 when DTC P0753 is output and check \
the shift solenoid valve No. 2
when DTC P0758 is output.
DTC No.DTC Detecting ConditionTrouble Area
P0753
P0758
The ECM checks for an open or short circuit in the shift sole-
noid valves No. 1 and No. 2 circuit when it changes
The ECM records DTC P0753 or P0758 if condition (a) or (b) is
detected once, but it does not light up MIL
After ECM detects condition (a) or (b) continuously 8 times or
more in one− trip, it causes the MIL light up until condition (a) or
(b) disappears
After that, if the ECM detects condition (a) or (b) once, it starts
lighting up MIL again
(a) Solenoid resistance is 8 Ω or less (short circuit) when the
solenoid is energized
(b) Solenoid resistance is 100 k Ω or more (open circuit) when
the solenoid is not energized
 Open or short in shift solenoid valve No. 1/No. 2 circuit
 Shift solenoid valve No. 1/No. 2
 ECM
DI5KO−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07464
Solenoid Valve SLTransmission
ECM
B+
R−L
3
EC2
Y 8
E4 SL
R−L
3
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−163
1996 LAND CRUISER (RM451U)
DTC P0773 Shift Solenoid E Electrical Malfunction
(Shift Solenoid Valve SL)
CIRCUIT DESCRIPTION
The shift solenoid valve SL is turned ON and OFF by signals from the ECM to control the hyd\
raulic pressure
acting on the lock−up relay valve, which then controls operation of the lock −up clutch.
Fail Safe Function:
If the ECM detects a malfunction, it turns the shift solenoid valve SL O\
FF.
DTC No.DTC Detecting ConditionTrouble Area
P0773Open or short in shift solenoid valve SL circuit for 1 time
(2 trip detection logic) Open or short in shift solenoid valve SL circuit
 Shift solenoid valve SL
 ECM
WIRING DIAGRAM
DI5KS−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5Q5−02
W02056
1
2
3
4
567
8910 A
B
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−245
1996 LAND CRUISER (RM451U)
TERMINALS OF ECM
No.SymbolTerminal Name
A−Electrical Connection Check Mechanism
B−Electrical Connection Check Mechanism
1P−Squib  (Passenger)
2P+Squib  (Passenger)
3D−Squib  (Driver)
4D+Squib  (Driver)
5E1Ground
6E2Ground
7TcDiagnosis
8LASRS Warning Light
9IG2Power Source (IGN Fuse)
10ACCPower Source (CIG Fuse)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00489
Cruise Control ECUL
L−
W−B
1
5
4 3
2 R
1026
C4 Stop Light Switch
4
R−G
Cruise
Control Actuator
C17
C17
C17
C4S13
S13 S13
S13
G−O G−WF11F11
1
2
STOP
Instrument Panel Fuse Block
W
EA3
W
3
1
F8
Battery Fusible Link
FL MAIN
STP−
DI−298
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
DTC 12 Actuator Magnetic Clutch Circuit
CIRCUIT DESCRIPTION
This circuit turns on the magnetic clutch inside the actuator during cruise \
control operation according to the
signal from the ECU. If a malfunction occurs in the actuator or speed sensor, etc. during cruise control opera-
tion, the rotor shaft between the motor and control plate is released.
When the brake pedal is depressed, the stop light switch turns on, supplying electrical power to the stop light.
Power supply to the magnetic clutch is mechanically cut and the magnetic clut\
ch is turned OFF.
When driving downhill, if the vehicle speed exceeds the set speed by 15 km/h\
(9 mph), the ECU turns the
safety magnet clutch OFF. If the vehicle speed later drops to within 10 km/h (6 mph) above the\
set speed,
then cruise control at the set speed is resumed.
DTC No.Detection ItemTrouble Area
12 Short in actuator magnetic clutch circuit.
 Open (0.8 sec.) in actuator magnetic clutch circuit.
STOP Fuse
 Stop light switch
 Actuator magnetic clutch
 Harness or connector between cruise control ECU and
actuator magnetic clutch, actuator magnetic clutch and body
ground
 Cruise control ECU
WIRING DIAGRAM
DI5OC−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010