1996 TOYOTA LAND CRUISER ignition

Q07312
DI−142
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
9. MANUAL SHIFTING TEST
The purpose of this manual shifting test is to determine whether
a problem is caused by either mechanical or electrical factors.
Disconnecting the solenoid wire disables electrically −con-
trolled automatic gear shifting. In this case, operating the shift
lever is the only way to shift the transmission gear. If the gear
is not changed by shift lever operation, it is assumed that there
is a mechanical problem.
(a) Turn the ignition switch OFF.
(b) Disconnect the solenoid wire connector.
(c) Warm up the engine.
(d) Drive the vehicle.
(e) Check the transmission operation when the shift lever is moved into L, 2 and D positions.
Standard:
Shift LeverOperation
L to 2Shift up
2 to DShift up
D to 2Shift down
2 to LShift down
(f) Turn the ignition switch OFF.
(g) Connect the solenoid wire connector.
(h) Clear DTCs.
HINT:
When the solenoid wire is disconnected, the transmission gear
will be set as listed below:
Shift LeverGear
PParking
RReverse
NNeutral
DO/D (4th)
23rd
L1st
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08577D00180
ECM
Combination Meter
Battery
Park/Neutral
Position Switch
Fuse Block
Starter
From
Battery L
2
R
NSW
E717
16 15
C12
G−W
E7E7
E7
L
R
2
C12
C12
R−B R−B
G−W
O
O
IH2
B−W 22
43
1
2B−W
IG1
ST1 2 4
AM1
2
2
2 2
1
2
AM1
3
J4
EA2 1 8
GAUGE
W
B F6
FLAM1
B+
IH2
IH1 IH1
B−L
B
6
Ignition Switch
4 R/B No. 2
6
6
B
B
Y
Y
15
B−R
B−WO
G−R R−B
S1
S2
10 4
11
2
3
21 7
Y
B−Y 1
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−169
1996 LAND CRUISER (RM451U)
DTC P1780 Park/Neutral Position Switch Malfunction
CIRCUIT DESCRIPTION
The park/neutral position switch detects the shift lever position and sends\
signals to the ECM.
The ECM receives signals (NSW, R, 2 and L) from the park/neutral position switch. When the signal is\
not
sent to the ECM from the park/neutral position switch, the ECM judges th\
at the shift lever is in D position.
DTC No.DTC Detection ConditionTrouble Area
P1780
2 or more switches are ON simultaneously for N, 2 and L posi-
tions (2 trip detection logic)
Short in park/neutral position switch circuit
 Park/neutral position switch
 ECMWhen driving under conditions (a), (b) and (c) for 30 sec. or
more, the park/neutral position switch is ON (N position)
(2 trip detection logic)
(a) Vehicle speed: 70 km/h (44 mph) or more
(b) Engine speed: 1,500 − 2,500 rpm
(c) Engine load: 0.6 g/rev. or more
WIRING DIAGRAM
DI5KY−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE3840
Q08479D00090
ON
(−)
(+)
NSWR
2
L
Position
P, NR
D
2
L NSW
−
Body ground R −

Body ground 2 −

Body ground L −

Body ground
Below 1.5 V
7.5 − 14 V
7.5 −
14 V*
7.5 − 14 V
Below 1.5 V
Below 1.5 V
Below 1.5 V Below1.5 V
Below 1.5 V
Below 1.5 V Below1.5 V
Below 1.5 V
9 − 14 V
Below 1.5 V
Below 1.5 V
Below 1.5 V
9 −
14 V
9 − 14 V
9 − 14 V Below 1.5 V
DI−170
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Read PNP, REVERSE, 2ND and LOW signals.
When using TOYOTA hand −held tester:
PREPARATION:
(a) Remove the fuse box cover.
(b) Connect a TOYOTA hand−held tester to the DLC3.
(c) Turn the ignition switch ON and TOYOTA hand−held tes-
ter main switch ON.
CHECK:
Shift lever into the P, R, N, 2 and L positions, and read the PNP,
REVERSE, 2 and L signals on the TOYOTA hand −held tester.
OK:
Shift positionSignal
22ND OFF → ON
LLOW OFF → ON
RREVERSE OFF → ON
P, NPNP SW OFF → ON
When not using TOYOTA hand −held tester:
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminals NSW, 2 and L of ECM
and body ground when the shift lever is shifted to the following
positions.
OK:
*: The voltage will drop slightly due to lighting up of the back up
light.
OK Check and replace ECM.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07467
Cruise Control ECUOD OD1B+
G−O
9 18ECM
E7
BE3840
Q07658 D00091
ON
(−) (+) OD1
DI−172
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
O/D Cancel Signal Circuit
CIRCUIT DESCRIPTION
While driving with cruise control activated, in order to minimize gear shifting and provide\
smooth cruising on
an uphill, overdrive may be prohibited temporarily in some conditions.
The cruise control ECU sends O/D cut signals to the ECM as necessary and\
the ECM cancels overdrive
shifting until these signals are discontinued.
(For details, see the Cruise Control section, page DI−292)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check voltage between terminal OD1 of ECM and body ground.
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminal OD1 of the ECM and
body ground.
OK:
Voltage: 9 − 14 V
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−147 ).
NG
DI5L0−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE3840
Q07660 D00015
ON
OD
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−173
1996 LAND CRUISER (RM451U)
2 Check voltage between terminal OD of cruise control ECU harness side connec-
tor and body ground.
PREPARATION:
(a) Disconnect the cruise control ECU connector.
(b) Turn ignition switch ON.
CHECK:
Measure the voltage between terminal OD of the cruise control
ECU harness side connector and body ground.
OK:
Voltage: 9 − 14 V
OK Check and replace cruise control ECU.
NG
3 Check harness and connector between cruise control ECU and ECM (See pag\
e IN−28 ).
NG Repair or replace wire harness or connector.
OK
Check and replace ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08582
ECM
O/D OFF Indicator Light
(Combination Meter)
Ignition Switch
Fuse BlockO/D Main Switch* E7
2
P−L
B−L Y
GAUGE
Battery B+
W
2
Y
3 2
4 4
2
2 2
4
W−B
6
FL AM1
B−Y
22
E6 A
A
EA2 C12
C12
19
OD2
B ID2
J1
B 9
1
1 8
3
Fuse Block
P−L
P−L
AM1
2
BF
R/B No. 2 R/B No. 2
O/D Main switch
Contact go off with switch pushed in.
Contact go on with switch once again.
*:
DI−174
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
O/D Main Switch & O/D OFF Indicator Light Circuit
CIRCUIT DESCRIPTION
The O/D main switch contacts go off when the switch is pushed in and come on when it is pushed once again.\
In O/D main switch OFF position, the O/D OFF indicator lights up, and the \
ECM prohibits shifting to O/D.
WIRING DIAGRAM
DI5L3−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

D00077 BE3840D00092
ON
ON
OFF
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−175
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
O/D OFF indicator light does not light up:
1 Check operation of O/D main switch.
CHECK:
(a) Turn the ignition switch ON.
(b) Check the O/D OFF indicator light when the O/D main
switch is pushed in to ON.
OK:
O/D OFF indicator light goes off
CHECK:
Check the O/D OFF indicator light when the O/D main switch is
pushed again to OFF.
OK:
O/D OFF indicator light lights up
NG Go to step 4.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE3840
Q08230D00093
ON
OD2
DI−176
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
2 Check OVRDRIVE CUT SW2 signal.
When using TOYOTA hand −held tester:
PREPARATION:
(a) Remove the fuse box cover.
(b) Connect a TOYOTA hand−held tester to the DLC3.
(c) Turn the ignition switch ON and TOYOTA hand−held tes-
ter main switch ON.
CHECK:
Read the OVRDRIVE CUT SW2 signal on the TOYOTA hand −
held tester.
OK:
O/D Main SwitchOVRDRIVE CUT SW2 Signal
O/D ON (pushed in)OFF
O/D OFF (pushed out)ON
When not using TOYOTA hand −held tester:
PREPARATION:
Turn the ignition switch ON.
CHECK:
Check the voltage between terminal OD2 of the ECM and body
ground.
OK:
O/D Main SwitchVoltage
O/D ON9 − 14 V
O/D OFFBelow 3 V
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI−147 ).
NG
3 Check harness and connector between O/D OFF indicator light and ECM (Se\
e page IN−28 ).
NG Repair or replace harness or connector.
OK
Check and replace ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010