1996 TOYOTA LAND CRUISER automatic transmission

Q08235
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−181
1996 LAND CRUISER (RM451U)
3 Check PWR mode switch.
PREPARATION:
Disconnect the pattern select switch connector.
CHECK:
Check the resistance between terminals of the pattern select
switch connector when the PWR mode switch is set to PWR and
NORM positions.
OK:
PWR Mode SwitchResistance
PWR0 Ω (continuity)
NORM∞ Ω (open)
NG Replace pattern select switch.
OK
4 Check harness and connector between battery and pattern select switch, a\
nd pattern select switch and ECM (See page IN−28).
NG Repair or replace harness or connector.
OK
Check and replace ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08580
R−W
J1
A
W 5BRY
IG3
O
Ignition Switch
Fuse Block
GAUGE
Pattern Select Switch*
(2nd Start Switch)
B ECM
18
IH2 12
HI
1
113
9
E4
2C12
Battery
FL AM1
Fuse Block
B−L
W
B−Y
2
4
F6
6 A
A
Y
3
1
E4HOLD
2
EA2
AM1
22
1
AM1 IG1
B
C12
ID3 IH2
O
R−W
2 2
3
42nd STRT Indicator Light
(Combination Meter)
12
Y
R/B No. 2 R/B No. 2
Pattern Select Switch (2nd Start Switch)
When the 2nd start switch is pushed, the switch is contacted and the 2nd\
mode is selected.
To cancel the 2nd start, push the 2nd start swtch once again. The 2nd star\
t is automatically cancelled
out when the ignition switch is turned OFF.
*:
DI−182
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
Pattern Select Switch Circuit (2nd Start Switch) & 2nd Start
Switch Indicator Light Circuit
CIRCUIT DESCRIPTION
When 2nd start mode is selected with the pattern select switch, the ECM cont\
rols the solenoid valves and
the transmission starts from 2nd gear.
In D position, the transmission automatically shifts up through 3rd to O\
/D as usual.
In 2nd position, the transmission is held in 2nd gear.
WIRING DIAGRAM
DI5L8−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE3840
Q07359D00023
ON
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−183
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check operation of 2nd start switch.
CHECK:
(a) Turn the ignition switch ON.
(b) Check the ”2nd STRT” indicator light when the 2nd start
switch is pushed in to ON.
OK:
”2nd STRT” indicator light lights up.
CHECK:
Check the ”2nd STRT” indicator light when the 2nd start switch
is pushed again, or PWR mode switch is pushed into OFF.
OK:
”2nd STRT” indicator light goes off. When PWR mode
switch is pushed in to ON, ”2nd STRT” indicator light
goes off, and ”PWR” indicator light lights up.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−147 ).
NG
2 Check 2nd start indicator bulb.
NG Replace 2nd start indicator bulb.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08234
D00096
ONHOLD
HI
DI−184
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
3 Check 2nd start switch.
PREPARATION:
Disconnect the pattern select switch connector.
CHECK:
Check the resistance between terminals 2 and 5 of the pattern
select switch connector when the pattern select switch is set to
2nd start switch ON and OFF.
OK:
2nd Start SwitchResistance
ON0 Ω (continuity)
OFF∞ Ω (open)
NG Replace pattern select switch.
OK
4 Check voltage between terminals HOLD and HI of ECM and body ground.
PREPARATION:
(a) Turn ignition switch ON.
(b) Disconnect the connector from the ECM.
CHECK:
Check the voltage between terminal HOLD of the ECM and
body ground when the select switch is set to 2nd start switch ON
and OFF.
OK:
2nd Start SwitchVoltage
ON9 − 14 V
OFFBelow 1.5 V
CHECK:
Check the voltage between terminal HI of the ECM and body
ground.
OK:
Voltage: 7.5 − 14 V
OK Check and replace ECM.
NG
Check and replace harness and connector between battery and patten select switch, pattern se-
lect switch and ECM, battery and 2nd start indicator light, and 2nd start in\
dicator light and ECM
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08580
R-W
J1
A
W 5BRY
IG3
O
Ignition Switch
Fuse Block
GAUGE
(*) Pattern Select Switch
(2nd Start Switch)
B
ECM
18
IH2 12
HI
1
113
9
E4
2
C12
Battery
FL AM1
Fuse Block
B-L
W
B-Y
2
4
F6
6 A
A
Y
3
1
E4HOLD
2
EA2
AM1
22
1
AM1 IG1
B
C12
IG3 IL2
O
R-W
2 2
3
42nd STRT Indicator Light
(Combination Meter)
12
Y
R/B No.2 R/B No.2
DI-185
-
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
Pattern Select Switch Circuit (2nd Start Switch) & 2nd Start
Switch Indicator Light Circuit
CIRCUIT DESCRIPTION
When 2nd start mode is selected with the pattern select switch, the ECM cont\
rols the solenoid valves and
the transmission starts from 2nd gear.
In D position, the transmission automatically shifts up through 3rd to O\
/D as usual.
In 2nd position, the transmission is held in 2nd gear.
WIRING DIAGRAM
(*) Pattern Select Switch (2nd Start Switch)
When the 2nd start switch is pushed, the switch is contacted and the 2nd\
mode is selected.
To cancel the 2nd start, push the 2nd start switch once again. The 2nd sta\
rt is automatically cancelled out
when the ignition switch is turned OFF.
DI5L8-02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE3840
Q07359D00023
ON
-
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI-186
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check operation of 2nd start switch.
CHECK:
(a) Turn the ignition switch ON.
(b) Check º2nd STRTº indicator light when 2nd start switch is
pushed in to ON.
OK:
º2nd STRTº indicator light lights up.
CHECK:
Check º2nd STRTº indicator light when 2nd start switch is
pushed again, or PWR mode switch is pushed into OFF.
OK:
º2nd STRTº indicator light goes off. When PWR mode
switch is pushed in to ON, º2nd STRTº indicator light
goes off, and ºPWRº indicator light lights up.
OK Proceed to next circuit inspection shown on matrix chart (See page DI-150).
NG
2 Check 2nd start indicator bulb.
NG Replace 2nd start indicator bulb.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08234
D00096
ONHOLD
HI
DI-187
-
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
3 Check 2nd start switch.
PREPARATION:
Disconnect the pattern select switch connector.
CHECK:
Check continuity between terminals 2 and 5 of pattern select
switch connector when pattern select switch is set to 2nd start
switch ON and OFF.
OK:
2nd start switchSpecified condition
Press continuously º2ndº switch0 W (Continuity)
Release º2ndº switch8 W (open)
NG Replace pattern select switch.
OK
4 Check voltage between terminals HOLD and HI of ECM and body ground.
PREPARATION:
(a) Turn ignition switch ON.
(b) Disconnect the connector of ECM.
CHECK:
Check voltage between terminal HOLD of ECM and body
ground when the select switch is set to 2nd start switch ON and
OFF.
OK:
2nd start switchVoltage
ON9 - 14 V
OFFBelow 1.5 V
CHECK:
Check voltage between terminal HI of ECM and body ground.
OK:
Voltage: 7.5 - 14 V
OK Check and replace the ECM.
NG
Check and replace harness and connector between battery and patten select swi\
tch, pattern se-
lect switch and ECM, battery and 2nd start indicator light , 2nd start indic\
ator light and ECM
(See page IN-27 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL ENGINE UNIT
EM−81
1996 LAND CRUISER (RM451U)
26. CONNECT EVAP HOSE
27. CONNECT BRAKE BOOSTER VACUUM HOSE
28. CONNECT HEATER VALVE AND ENGINE WIRE TO
COWL PANEL
(a) Connect the heater valve with the 2 bolts.
(b) Connect the engine wire and ground strap with the 2 bolts.
29. CONNECT HEATER HOSES
30. CONNECT ACCELERATOR CABLE TO THROTTLE BODY
31. CONNECT CRUISE CONTROL ACTUATOR CABLE TO
THROTTLE BODY
32. INSTALL AIR CLEANER CASE
33. INSTALL AIR CLEANER HOSE AND CAP
34. CONNECT OIL COOLER HOSE TO OIL COOLER PIPE
35. INSTALL RADIATOR (See page CO−16)
36. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
37. INSTALL BATTERY TRAY AND BATTERY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery and hold−down clamp with the nuts.
(d) Connect the battery cables.
38. FILL WITH ENGINE OIL
39. FILL RADIATOR WITH ENGINE COOLANT
40. START ENGINE AND CHECK FOR LEAKS
41. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
42. CHECK IGNITION TIMING (See page EM−10)
43. INSTALL HOOD
44. PERFORM ROAD TEST
Check for abnormal noise, shock, slippage, correct shift points
and smooth operation.
45. RECHECK ENGINE COOLANT AND ENGINE OIL LEV-
ELS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010