1996 TOYOTA LAND CRUISER engine coolant

SF1EN−01
SF−26
−
SFI INJECTOR
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. DISCONNECT CRUISE CONTROL ACTUATOR CABLE
3. DISCONNECT ACCELERATOR CABLE
4. DISCONNECT THROTTLE CABLE
5. DISCONNECT NO.2 PCV HOSE
6. DISCONNECT AIR CLEANER HOSE
7. REMOVE EGR VACUUM MODULATOR AND VALVE (See page EC−10 )
8. REMOVE BOLT HOLDING HEATER INLET PIPE AND AIR INTAKE CHAMBER
9. DISCONNECT NO.1 PCV HOSE
10. DISCONNECT VACUUM SENSING HOSE
11. DISCONNECT NO.2 WATER BYPASS HOSE
12. DISCONNECT EVAP HOSE
13. DISCONNECT BRAKE BOOSTER HOSE
14. DISCONNECT THROTTLE POSITION SENSOR CON- NECTOR
15. DISCONNECT IDLE AIR CONTROL VALVE CONNEC-
TOR
16. DISCONNECT CONNECTOR FOR EMISSION CON- TROL VALVE SET ASSEMBLY
17. DISCONNECT EGR GAS TEMP. SENSOR CONNEC-
TOR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
SFI INJECTOR
SF−35
1996 LAND CRUISER (RM451U)
27. FILL WITH ENGINE COOLANT
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1EW−04
−
SFI THROTTLE BODY
SF−45
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. DISCONNECT NO.2 PCV HOSE
3. DISCONNECT AIR CLEANER HOSE
4. DISCONNECT CONTROL CABLES FROM THROTTLE
BODY
5. DISCONNECT THROTTLE POSITION SENSOR CON-
NECTOR
6. DISCONNECT IDLE AIR CONTROL VALVE CONNEC- TOR
7. REMOVE THROTTLE BODY
(a) Disconnect the EVAP hose.
(b) Disconnect the 3 vacuum hoses.
(c) Disconnect the No.2 water bypass hose.
(d) Remove the 4 bolts, and disconnect the throttle body from
the air intake chamber.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
(e) Remove the throttle body gasket.
HINT:
At the time of installation, plaese refer to the following items.
install a new gasket on the air intake chamber.
(f) Disconnect the No.1 water bypass hose from the throttle
body, and remove the throttle body.
(g) Disconnect the No.2 water bypass hose from the throttle
body.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0PO−09
Z02917
Ohmmeter
TEMPERATURE °C (° F)
RESISTANCE kΩ
Acceptable
−
SFI ENGINE COOLANT TEMPERATURE (ECT) SENSOR
SF−61
689
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE COOLANT
TEMPERATURE (ECT) SENSOR
INSPECTION
1. DRAIN ENGINE COOLANT
2. REMOVE ECT SENSOR
(a) Disconnect the ECT sensor connector.
(b) Using a 19 mm deep socket wrench, remove the ECT
sensor and gasket.
3. INSPECT ECT SENSOR
Using an ohmmeter, measure the resistance between the ter-
minals. Resistance: Refer to the chart graph
If the resistance is not as specified, replace the ECT sensor.
4. REINSTALL ECT SENSOR
(a) Using a 19 mm deep socket wrench, install the ECT sen- sor and gasket.
Torque: 24.5 N·m (250 kgf·cm, 17.5 ft·lbf)
(b) Connect the ECT sensor connector.
5. REFILL ENGINE COOLANT
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EJ−02
SS−40
−
SERVICE SPECIFICATIONS BODY ELECTRICAL
163
Author: Date:
1996 LAND CRUISER (RM451U)
BODY ELECTRICAL
SERVICE DATA
TURN SIGNAL FLASHER
Flashes/Minute60 − 120
SPEEDOMETER (USING A SPEEDOMETER)
Standard indication (mph)Allowable range (mph)
2018 − 24
4038 − 44
6058 − 66
8078 − 88
10098 − 11 0
12011 8 − 132
TACHOMETER (ON− VEHICLE) DC 13.5 V 25°C (77° F)
Standard indication (RPM)Allowable range (RPM)
700630 − 770
1,000900 − 1,100
2,0001,875 − 2,125
3,0002,850 − 3,150
4,0003,850 − 4,150
5,0004,850 − 5,150
FUEL RECEIVER GAUGE
A − B85.5 − 105.5 Ω
A − C126 − 150 Ω
B − C90 − 110 Ω
FUEL SENDER GAUGE
Float position F: Approx. 15 mm ((0.59 in.)Approx. 3 Ω
Float position E: Approx. 200 (7.87 in.)Approx. 110 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE
A − B71 − 79 Ω
A − C117 − 141 Ω
B − C185 − 215 Ω
OIL PRESSURE RECEIVER GAUGE
Resistance40 − 48 Ω
CRUISE CONTROL SWITCH
Switch position OFFNo continuity
Switch position RESUME/ACCELApprox. 68 Ω
Switch position SET/COASTApprox. 198 Ω
Switch position CANCELApprox. 418 Ω
CRUISE CONTROL ACTUATOR
1 − 3Approx. 2 kΩ
2 − 3Approx. 0.5 − 1.7 kΩ
Actuator control arm free play0 mm (0 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010