Page 762 of 1399
I00497
Cruise Control ECU
B−R BATT
C17
W
W Instrument Panel Fuse Block
Fusible Link
F8 F11
F11
EA3
FL MAIN
Battery 3
ECU−B 15
2
1
N18670
Junction Block No.1
ECU−IG
Fuse
DI−328
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Back −up Power Source Circuit
CIRCUIT DESCRIPTION
The ECU back− up power source provides power even when the ignition is off and is used for DTC memory,
etc..
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check ECU −IG fuse.
PREPARATION:
Remove the ECU −IG fuse from relay block No.2.
CHECK:
Check continuity of ECU −IG fuse.
OK:
Continuity
NG Check for short in all the harness and compo- nents connected to the ECU −IG fuse.
OK
DI5ON−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 764 of 1399
AB0119I00013 I00028
ONCMS
(−)
(+)
DI−330
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Main Switch Circuit (Cruise Control Switch)
CIRCUIT DESCRIPTION
When the cruise control main switch is turned off, the cruise control does not operate.
WIRING DIAGRAM
See page DI−311 .
INSPECTION PROCEDURE
1 Check voltage between terminal CMS of cruise control ECU connector and body
ground.
PREPARATION:
(a) Remove the ECU with connector still connected.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal CMS of cruise control ECU
connector when main switch is held on and off.
OK:
Main switchVoltage
OFF10 − 14 V
ONBelow 2 V
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI−295 ).
NG
DI5OO−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 766 of 1399
I00498
Cruise Control ECU
C17
Battery Fusible
Link
F6 B−L W
B
B G−Y
F11 F11
GAUGE
Y
2
Y9
CRUISE MAIN Indicator (Combination Meter)C10
C10
2 2 2
2
22
43
EA2
6
Ignition Switch
I12 I12
4
Instrument Panel Fuse Block
1
AM1
AM1 J1
JUNCTION
CONNECTOR
PI
7
DI−332
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
CRUISE MAIN Indicator Light Circuit
CIRCUIT DESCRIPTION
When the cruise control main switch is turned ON, CRUISE MAIN indicator ligh\
t lights up.
WIRING DIAGRAM
DI5OP−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 768 of 1399
I00499
Cruise Control ECU
DLC1
TC D111
B−Y IH111
B−YC17 TC8
N06219
DLC1
TC
E1
DI−334
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Diagnosis Circuit
CIRCUIT DESCRIPTION
This circuit sends a signal to the ECU that DTC output is required.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check voltage between terminals Tc and E1 of DLC1.
PREPARATION:
Turn ignition switch ON.
CHECK:
Measure voltage between terminals Tc and E1 of DLC1.
OK:
Voltage: 10 − 14 V
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
DI5OQ−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010