1996 TOYOTA COROLLA lock

74
Your automatic transmission has a shift
lock system to minimize the possibility of
incorrect operation. This means you can
only shift out of Pº position when the
brake pedal is depressed (with the ignition
switch in ONº position and the lock re-
lease button depressed).
(a) Normal Driving
1. Start the engine as instructed in How
to start the engineº in Part 3. The trans-
mission must be in Pº or Nº.
2. With your foot holding down the brake
pedal, shift the selector lever to Dº.
In Dº position, the automatic transmis-
sion system will select the most suitable
gear for running conditions such as nor-
mal cruising, hill climbing, hard towing,
etc.
Never put your foot on the accelera-
tor pedal while shifting.CAUTION
!
3. Release the parking brake and brake
pedal. Depress the accelerator pedal
slowly for smooth starting.(b) Using engine braking
To use engine braking, you can downshift
the transmission as follows:

Shift into the 2º position when the ve-
hicle speed is lower than the maximum
allowable speed for second gear. The
transmission will downshift to the sec-
ond gear and more engine braking will
be obtained.

Shift into the Lº position when the ve-
hicle speed is lower than the maximum
allowable speed for Lº position. The
transmission will downshift to the first
gear and maximum engine braking will
be applied.
MAXIMUM ALLOWABLE SPEEDS
2º 112 km/h (70 mph). . . . . . . . . . . .
Lº 62 km/h (38 mph). . . . . . . . . . . . .
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.CAUTION
! Automatic transmission
(3-speed type)
ProCarManuals.com

75
NOTICE
Be careful not to overrev the en-
gine. Watch the tachometer to
keep engine rpm from going into
the red zone. The maximum allow-
able speed (approximate) for each
position is given above for your
reference.
Do not continue hill climbing for a
long time in the 2º or Lº position.
This may cause severe automatic
transmission damage from over-
heating. To prevent such damage,
use Dº position for hill climbing
or hard towing.
(c) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with
your foot, shift the selector lever to the Rº
position.
NOTICE
Never shift into reverse while the
vehicle is moving.
(d) Parking
1. Bring the vehicle to a complete stop.
2. Pull the parking brake lever up fully to
securely apply the parking brake.
3. With the brake pedal pressed down,
shift the selector lever to the Pº position.
While the vehicle is moving, never
attempt to move the selector lever
into Pº position under any circum-
stances. Serious mechanical dam-
age and loss of vehicle control may
result.CAUTION
!
(e) Good driving practice
Always keep your foot on the brake
pedal while stopped with the engine
running. This prevents the vehicle
from creeping.CAUTION
!
NOTICE
Do not hold the vehicle on an
upgrade with the accelerator pedal.
It can cause the transmission to
overheat. Always use the brake
pedal or parking brake.
(f) If you cannot shift the selector lever
out of Pº position
If you cannot shift the selector lever from
Pº position even though the brake pedal
is depressed, use the shift lock override
button. For instructions, see If you can-
not shift automatic transmission selector
leverº in Part 4.
Automatic transmission
(4-speed type)
ProCarManuals.com

76
Your automatic transmission has a shift
lock system to minimize the possibility of
incorrect operation. This means you can
only shift out of Pº position when the
brake pedal is depressed (with the ignition
switch in ONº position and the lock re-
lease button depressed).
(a) Normal Driving
1. Start the engine as instructed in How
to start the engineº in Part 3. The trans-
mission must be in Pº or Nº.
2. With your foot holding down the brake
pedal, shift the selector lever to Dº.
In Dº position, the automatic transmis-
sion system will select the most suitable
gear for running conditions such as nor-
mal cruising, hill climbing, hard towing,
etc.
Always turn the overdrive switch on for
better fuel economy and quieter driving. If
the engine coolant temperature is low, the
transmission will not shift into the over-
drive gear even with the overdrive switch
on.
Never put your foot on the accelera-
tor pedal while shifting.CAUTION
!
3. Release the parking brake and brake
pedal. Depress the accelerator pedal
slowly for smooth starting.(b) Using engine braking
To use engine braking, you can downshift
the transmission as follows:

Turn off the overdrive switch. The O/D
OFFº indicator light will come on and
the transmission will downshift to the
third gear.

Shift into the 2º position. The trans-
mission will downshift to the second
gear when the vehicle speed drops
down to or lower than the maximum al-
lowable speed for second gear, and
more powerful engine braking will be
obtained.

Shift into the Lº position. The trans-
mission will downshift to the first gear
when the vehicle speed drops down to
or lower than the maximum allowable
speed for Lº position and maximum
engine braking will be applied.
MAXIMUM ALLOWABLE SPEEDS
2º 110 km/h (68 mph). . . . . . . . . . . .
Lº 60 km/h (38 mph). . . . . . . . . . . . .
ProCarManuals.com

77
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.CAUTION
!
NOTICE
Be careful not to overrev the en-
gine. Watch the tachometer to keep
engine rpm from going into the red
zone. The maximum allowable
speed (approximate) for each posi-
tion is given above for your refer-
ence.
Do not continue hill climbing for a
long time in the 2º or Lº position.
This may cause severe automatic
trasmission damage from over-
heating. To prevent such damage,
use Dº position for hill climbing
or hard towing.
(c) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with
your foot, shift the selector lever to the Rº
position.
NOTICE
Never shift into reverse while the
vehicle is moving.
(d) Parking
1. Bring the vehicle to a complete stop.
2. Pull the parking brake lever up fully to
securely apply the parking brake.
3. With the brake pedal pressed down,
shift the selector lever to the Pº position.
While the vehicle is moving never
attempt to move the selector lever
into Pº position under any circum-
stances. Serious mechanical da-
mage and loss of vehicle control
may result.CAUTION
!
(e) Good driving practice

If the transmission is repeatedly up-
shifted and downshifted between third
gear and overdrive when climbing a
gentle slope, the overdrive switch
should be turned off. Be sure to turn
the switch on immediately afterward.

When towing a trailer, in order to main-
tain engine braking efficiency, do not
use overdrive.
Always keep your foot on the brake
pedal while stopped with the engine
running. This prevents the vehicle
from creeping.CAUTION
!
NOTICE
Do not hold the vehicle on an
upgrade with the accelerator pedal.
It can cause the transmission to
overheat. Always use the brake
pedal or parking brake.
(f) If you cannot shift the selector lever
out of Pº position
If you cannot shift the selector lever from
Pº position even though the brake pedal
is depressed, use the shift lock override
button. For instructions, see If you can-
not shift automatic transmission slelector
leverº in Part 4.
ProCarManuals.com

Part 1Car audio system operating tips
83
OPERATION OF
INSTRUMENTS
AND CONTROLSÐ
Chapter 1-7
Car audio system
and Air conditioning
system
Car audio system operating tips
AM-FM radio with electronic
tuner
AM-FM radio with electronic
tuner and cassette tape player
Air conditioning controls
Heater controls
Side vents
You can listen to the car audio system
when the ignition key is at ONº or
ACCº. However, if the engine is not
running, the key must be in the ACCº
position.
ILLUMINATION CONTROL LOGIC
On some audio-units, when the instru-
ment panel lights are on, the letters on op-
erable buttons of the mode in current use
light up together with the mode selection
and eject buttons.
RADIO
FM reception tips
Most of us are not aware that a vehicle is
not an ideal place to listen to a radio. Be-
cause it moves, reception conditions
change continuously. Buildings, terrain,
signal distance and noise from other ve-
hicles are all working against good recep-
tion. Some FM reception conditions may
appear to be problems even though they
are normal.
The following characteristics are normal
for a given reception area, and they do not
indicate any problem with the radio itself.
Fading and Drifting: On the average,
the broadcast range of FM stations is
limited to about 40 km (25 miles), ex-
cept for some high power stations.If a vehicle is moving away from the
desired station's transmitter, the signal
will tend to fade and/or drift. This phe-
nomenon is more noticeable with FM
than with AM, and is accompanied by
distortion.
Fading and drifting can be minimized
to a certain degree by fine tuning, or
you should tune in to a stronger signal.
Static and Fluttering: When the line-
of-sight path between a transmitter
and vehicle is blocked by large build-
ings or the like, static or fluttering may
occur because of the characteristic of
FM. In a similar effect, a fluttering
noise is sometimes heard when driv-
ing along a tree-lined road.
This static and fluttering can be re-
duced by adjusting the tone control for
greater bass response until the distur-
bance has passed.
Multipath: Because of the reflection
characteristics of FM, direct and re-
flected signals may reach the antenna
at the same time (a phenomenon
called multipath reception) and cancel
each other out. As a vehicle moves
through these electronic dead spots,
the listener may hear a momentary
flutter or lose reception.

ProCarManuals.com

84Station swapping: When two FM sta-
tions are close to each other, and an
electronic dead spot, such as is
caused by static or multipath recep-
tion, interrupts the original signal,
sometimes the stronger second signal
is picked up automatically until the
original one returns. This swapping
can also occur as you drive away from
the selected station and approach
another station with a stronger signal.
On models with a power antenna, the an-
tenna automatically extends to its full
height when the radio and ignition are
turned on.
To lower the power antenna, turn off the
audio system by pushing PWR.VOLº, or
turn the ignition key to LOCKº.
On some models, the power antenna au-
tomatically retracts when the radio mode
is switched off to turn on the cassette tape
player.
Before extending the power antenna,
confirm that no one is close enough to get
injured by it.
To prevent damage to the antenna,
make sure it is retracted before
driving your vehicle through an
automatic car wash.
NOTICE
CASSETTE TAPE PLAYER
Use only undamaged cassette tapes of
good quality. Avoid using tapes with a
total playing time longer than 90 min-
utes.
Using damaged tapes will cause trouble
with the tape player. Longer tapes are not
recommended because of their thinness.
Before inserting a cassette, make sure
the tape is not slack and that the label
is firmly stuck on the shell.
Wind the tape firmly by turning the hub
with a pencil or the like.
Be careful not to touch the exposed tape
surface.
When not in use, take the cassette out
of the player, put it back into its case
and store it away from dust, magnets
and direct sunlight.
Leaving cassettes on the dashboard in
the sun could damage your tapes.
Keep the playback head, capstan and
pinch roller clean.
Remove tape coating residue accumu-
lated on the head, capstan and pinch roll-
er once or twice a month. A cleaning tape
is available on the market.
Do not oil any part of the player and
do not insert anything other than
cassette tapes into the slot, or the
tape player may be damaged.
NOTICE
ProCarManuals.com

96(e) Windshield defogging and defrost-
ing
To remove interior fog on the windshield:
1. Place the temperature control lever at
any position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Move the air flow control lever to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Move fan speed control lever any-
where except the OFFº position.
5. Press in the air conditioning on-off but-
ton.
To remove frost or exterior fog on the
windshield:
1. Place the temperature control lever at
the HIGH position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Move the air flow control lever to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Move fan speed control lever to the
HIº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.(f) Air flow selection
FACE positionÐThis position directs the
air flow to face level.
BI-LEVELÐThis position directs the air
flow to face level and floor. Except in ven-
tilation, the air to the floor is slightly warm-
er than that to the face level.
FLOOR positionÐThis position directs
the air flow mostly to the floor.
FLOOR / WINDSHIELD position Ð This
position directs the air flow to the wind-
shield and front side windows as well as
the floor.
WINDSHIELD positionÐThis position di-
rects the air flow mostly to the windshield,
front side windows.
Do not use the WINDSHIELD position
during cooling operation in extremely hu-
mid weather. The difference between the
temperature of the outside air and that of
the windshield could cause the outer sur-
face of the windshield to fog up blocking
your vision.
(g) Operating tips

Be sure the air inlet grilles in front of the
windshield are not blocked by leaves
or other obstructions.
If air flow control is not satisfactory,
check the side vents. (See Side
ventsº after Heater controlsº.)

To help cool down the interior after
parking in the hot sun, drive for the first
few minutes with the windows open.
After the excess heat has blown away,
close the windows.

When driving on dusty roads, close all
windows. If dust thrown up by the ve-
hicle is still drawn into the vehicle after
closing the windows, it is recom-
mended that the air intake control le-
ver be set to the OUTSIDE AIR posi-
tion and the fan speed control lever
anywhere except the OFFº position.

If following another vehicle on a dusty
road, or driving in windy and dusty con-
ditions, it is recommened that the air
intake control lever be temporarily set
to the RECIRCULATED AIR position,
which will close off the outside pas-
sage and prevent outside air and dust
from entering the vehicle interior.ProCarManuals.com

99 (b) Heating
1. Place the temperature control lever
anywhere except the NO HEAT position.
If cooler air is desired at face level for bi-
level operation, place the lever around the
middle.
2. Move the air intake control lever to the
OUTSIDE AIR position.
If quick circulation of heated air is desired,
move the lever to the RECIRCULATED
AIR position.
For normal use, it is best to keep the lever
in the OUTSIDE AIR position. Otherwise
the windows will fog up more easily.
3. Move the air flow control lever to the
FLOOR position.
If cooler air is desired at face level for bi-
level operation, move the lever to the BI-
LEVEL position.
If the windshield fogs up easily, move the
lever to the FLOOR/WINDSHIELD posi-
tion.
For detailed information on air flow control
including other settings, see (e) Air flow
selectionº.
4. Move fan speed control lever any-
where except the OFFº position.(c) Ventilation
1. Place the temperature control lever at
the NO HEAT position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Move the air flow control lever to the
FACE position.
For detailed information on air flow control
including other settings, see (e) Air flow
selectionº.
4. Move fan speed control lever any-
where except the OFFº position.
(d) Windshield defogging and defrost-
ing
1. Place the temperature control lever at
FULL HEATING position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Move the air flow control lever to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (e) Air flow selectionº.
4. Move fan speed control lever to the
HIº position.
(e) Air flow selection
FACE positionÐThis position directs the
air flow to face level.BI-LEVEL positionÐThis position directs
the air flow to face level and floor. Except
in ventilation, the air to the floor is slightly
warmer than that to face level.
FLOOR positionÐThis position directs
the air flow mostly to the floor.
FLOOR / WINDSHIELD position Ð This
position directs the air flow to the wind-
shield and front side windows as well as
the floor.
WINDSHIELD positionÐThis position di-
rects the air flow mostly to the windshield,
front side windows.
(f) Operating tips

Be sure the air inlet grilles in front of the
windshield are not blocked by leaves
or other obstructions.

If air flow control is not satisfactory, check
the side vents. (See Side ventsº.)

When driving on dusty roads, close all
windows. If dust thrown up by the ve-
hicle is still drawn into the vehicle after
closing the windows, it is recom-
mended that the air intake control le-
ver be set to the OUTSIDE AIR posi-
tion and the fan speed control lever
anywhere except the OFFº position.ProCarManuals.com