1996 TOYOTA AVALON buttons

90
5. Insert the magazine into the automatic
changer as shown above. Then close the
cover.The anti-theft system prevents the audio
system f
rom working after it has been dis-
connected. To activate the system, you
must set a three-digit security code. After
the system is set, SECº will appear in the
display each time the ignition is turned
from LOCKº to ACCº or ONº. Also, the
anti-theft light flashes every few seconds
while the ignition key is in the LOCKº
position.
You will need to know your security code
to reactivate your radio after electrical ser-
vice is performed on your vehicle.
Choose a security code that is easy to re-
member and keep a copy of it (not in your
Toyota).
NOTICE
If you pushed any wrong buttons on the anti- theft system, the following
messages will appear on the display.
ErrºÐYou have pushed wrong buttons.
1- 9ºÐIndicates the number of er-rors you have made. You may makeup to nine errors, but no more!
HELPºÐThe number of errors you can make was exceeded. The audiosystem is completely i noperable.
Contact your Toyota dealer.
Setting a security code for the first
time.
1. Turn off the audio system.
Turn the ignition key to ACCº.
Simultaneously push and hold in 1º, 6º,
and PWR/VOLº until SECº appears on
the display.
ÐAnti-theft system
(Types 1-3 and 2 only)
ProCarManuals.com

92If you pushed any wrong buttons,
Errº and the number of errors you
have made will appear on the display
before SECº does. Go back to step 2
and try again. If the display returns to
- - -º while you are entering the code,
go back to step 3.
To make sure the security code has been
accepted, turn the ignition to LOCKº and
then
back to ACC.º SECº should appear
on the display.
Choose a security code that is easy to re-
member and keep a copy of it (not in your
Toyota).
Changing the security code
1. Turn off the audio system.
Turn the ignition key to ACCº.
Simultaneously push and hold in 1º, 6º,
and PWR/VOLº until SECº appears on
the display.2. While you are holding in the  ~º side of
TUNEº push 1º.
The display will read - - -º.
On some models,  º and  º will also
turn on.
ProCarManuals.com

94If you pushed any wrong buttons,
Errº and the number of errors you
have made will appear on the display
before SECº does. Go back to step 2
and try again. If the display returns to
- - -º while you are entering the code,
go back to step 3.
To make sure the security code has been
accepted, turn the ignition to LOCKº and
then
back to ACCº. SECº should appear
on the display.
NOTICE
A tenth error will activate the anti-theft system and HELPº will
appear on the display. The audiosystem will be completelyinoperable. At this time, theanti-theft light also comes on. If this
occurs, contact your Toyota dealer.
Clearing the security code
1. Turn off the audio system.
Turn the ignition key to ACCº.
Simultaneously push and hold in 1º, 6º,
and PWR/VOLº until SECº appears on
the display.2. While you are holding in the  ~º side of
TUNEº, push 1º.
The display will read - - -º.
On some models,  º and º will also
turn on.
ProCarManuals.com

95
3. Input the existing three-digit code.
You have 10 seconds to enter each digit.
For example, 209º:
To set the first digit: Push 1º until the digit
you want appears on the display.
To set the second digit: Push 2º until the
digit you want appears on the display.
To set the third digit: Push 3º until the digit
you want appears on the display.4. The three-digit code should be on the
display.
Push SCANº.
The display will read - - -º.
5. Wait for 10 seconds until the security
system is deactivated and the display
goes dark.If you pushed any wrong buttons,
Errº and the number of errors you
have made will appear on the display
before SECº does. Go back to step 2
and try again. If the display returns to
- - -º while you are entering the code,
go back to step 3.
NOTICE
A tenth error will activate the anti-theft system and HELPº will
appear on the display. The audiosystem will be completelyinoperable. At this time, theanti-theft light also comes on. If this
occurs, contact your Toyota dealer.
ProCarManuals.com

97
If you pushed any wrong buttons,
Errº and the number of errors you
have made will appear on the display
before SECº does. Go back to step 2
and try again. If the display returns to
- - -º while you are entering the code,
go back to step 3.
To make sure the security code has been
accepted, turn the ignition to LOCKº and
then
back to ACCº. SECº should appear
on the display.
NOTICE
A tenth error will activate the anti-theft system and HELPº will
appear on the display. The audiosystem will be completelyinoperable. At this time, theanti-theft light also comes on. If this
occurs, contact your Toyota dealer.
ILLUMINATION CONTROL LOGIC
When the instrument panel lights are on,
the letters on operable buttons of the
mode in current use light up. On some au-
dio units, the mode selection and eject
buttons also light up.
On some audio-units, when a cassette
tape and compact disc are not in the slot
the letters on the tape and disc mode but-
tons do not light up, but the slot lights up
for easy access. Once a cassette tape or
compact disc is inserted, the letters on the
tape or disc mode buttons light up, and the
slot stops illuminating.
RADIO RECEPTION
Usually, a problem with radio reception
does not mean there is a problem with
your radioÐit is just the normal result of
conditions outside the vehicle.
For example, nearby buildings and terrain
can interfere with FM reception. Power
lines or telephone wires can interfere with
AM signals. And of course, radio signals
have a limited range, and the farther you
are from a station, the weaker its signal
will be. In addition, reception conditions
change constantly as your vehicle moves. Here are some common reception prob-
lems
that probably do not indicate a prob-
lem with your radio:
FM
Fading and drifting stationsÐGenerally,
the effective range of FM is about 40 km
(25 miles). Once outside this range, you
may notice fading and drifting, which in-
crease with the distance from the radio
transmitter. They are often accompanied
by distortion.
Multi-pathÐFM signals are reflective,
making it possible for two signals to reach
your antenna at the same time. If this hap-
pens, the signals will cancel each other
out, causing a momentary flutter or loss of
reception.
Static and flutteringÐThese occur when
signals are blocked by buildings, trees, or
other large objects. Increasing the bass
level may reduce static and fluttering.
Station swappingÐIf the FM signal you
are listening to is interrupted or weak-
ened, and there is another strong station
nearby on the FM band, your radio may
tune in the second station until the original
signal can be picked up again.
ÐCar audio system operating
hints
ProCarManuals.com

102AUTOº button (type 2 only)
For automatic operation of the air condi-
tioning,
press the AUTOº button. An indi-
cator light will illuminate to show that the
automatic operation mode has been se-
lected.
In the automatic operation mode, the air
conditioning selects the most suitable fan
speed and air flow according to the tem-
perature.
You may use manual controls if you want
to select your own settings.
To turn off the automatic operation, press
the OFFº button.
Fan speed selector
Turn the knob (type 1) or press the button
(type 2) to adjust the fan speed.
In automatic operation, you do not have to
adjust the fan speed unless you desire
another fan speed mode.
Temperature selector
Turn the knob to adjust the t emperatureÐ
to the right to warm, to the left to cool.
Air flow selector
Turn the knob (type 1) or press the buttons
(type 2) to select the vents used for air
flow.
Type 2 onlyÐIn automatic operation, you
do not have to select the air flow unless
you desire another air flow mode.
1. Panel ÐAir flows mainly from the in-
strument panel vents.
2. Bi-level ÐAir flows from both the floor
vents and the instrument panel vents.
3. Floor ÐAir flows mainly from the floor
vents. 4. Floor/Windshield
ÐAir flows mainly
from the floor vents and windshield vents.
5. Windshield ÐAir flows mainly from
the windshield vents.
For details about air flow selector settings,
see the illustration after A/Cº button.
ProCarManuals.com