1996 PONTIAC FIREBIRD instrument panel

To replace the battery in the Remote Lock
Control transmitter:
1. Carefully pry off the cover by inserting a dime (or
2. Lift off the back cover.
3. Remove and replace the battery. Use one battery,
similar object) in a slot between the covers and twist.
type CR2032, or a similar type. Put new battery in
printed side down.
4. Replace the back cover. Make sure the cover is on
tightly
so water won’t get in.
5. Check the trans,mitter operation. If the transmitter
does not work after battery replacement, it may need
to be resynchronized or matched to your vehicle. See
“Synchronization” in the Index.
It can be dangerous to drive with the hatch open
because carbon monoxide (CO) gas can come into
your vehicle. You can’t see or smell
CO. It can
cause unconsciousness
and even death.
If you must drive with the hatch open or if
electrical wiring or other cable connections
must pass through the seal between the body and
the hatch:
Make sure all windows are shut.
Wrn the fan on your heating or cooling
system to its highest speed with the setting
on
VENT. That will force outside air into
your vehicle. See “Comfort Controls” in
the Index.
instrument panel, open them all
the way.
If you have air outlets on or under the
See “Engine Exhaust” in the Index.
,ye*: ; -2
ProCarManuals.com

Feature Customization (Option)
Your Pontiac’s locks and lighting systems can be
programmed with several, different features.. The
features you can program depend upon the options that
came with your vehicle. The following list tells you the
features that can be programmed. Listed next
to each
feature is the option you need to have on your vehicle in
order to be able to program that particular feature.
Exit Lighting (available for all)
Delayed Illumination (available for all)
Last Door Closed Locking
(if equipped with power
door locks)
Lockout Prevention
(if. equipped with power
door locks)
Remote Lock Control Verification (if equipped with
Vehicle and Content Theft-Deterrent System)
Theft-Deterrent Arming.
Method (if equipped with
Vehicle and Content Theft-Deterrent System)
Theft-Deterrent Arming Verification
(if equipped
with Vehicle and Content Theft-Deterrent System)
Driver’s Door Alarm Delay (if equipped with
Vehicle and Content Theft-Deterrent System)
Shock Sensor Enable
(if equipped with Vehicle and
Content Theft-Deterrent System) To
program features, your vehicle must be
in the
programming mode. Follow these steps:
1. Put your key in the ignition.
2. Turn the ignition to the RUN position to disarm the
3. Turn the ignition to the OFF position.
4. Remove the RADIO fuse. This fuse is in the main
Vehicle .and Content Theft-Deterrent System.
fuse block, located on the left side of your
instrument panel. See “Fuses and Circuit Breakers”
in the Index.
5. Put the ignirion in the ACC posmon.
You should hear a chime to veiify that the system is
in programming mode. If the chime sounds once,
you will be able to program Exit Lighting, Delayed
Illumination, Last Door Closed Locking and Lockout
Prevention only.
If the chime sounds twice and your
vehicle
is equipped with the Vehicle and Content
Theft-Deterrent System, you will also be able to set
Remote Lock Control Verification, Arming Method,
Arrning Verification, Driver’s Door Delay and Shock
Sensor Enable.
2-16
ProCarManuals.com

Exit Lighting and Delayed Illumination Last Door Closed Locking and
Your vehicle comes with this feature set in Mode 4. This Lockout Prevention
means that your interior lamps will go on when the key
Your vehicle comes with this feature set in Mode 2.
is removed from the ignition switch and stay on for This means that your power door locks will not lock
25 seconds after closing the doors to help in exiting the
when the keys are in the ignition and a door is open.
vehicle. TO change the factory setting, do the following:
TO change the factory setting, do the following:
1. Turn the courtesy lamps on by turning the instrument 1. press the LOCK switch on the door.
2. Count the number of chimes you hear. The number of chimes tells you which mode your vehicle is
panel brightness control knob all the way up.
of chimes tells you which mode your vehicle is set for.
set for.
2. Count the number of chimes you hear. The number
3. Press the LOCK switch on the door until you hear
3. Turn the courtesy lamp switch to off. the number of chimes that correspond to the mode
4. Turn the courtesy lamp switch from on to off until
you hear the number of chimes that correspond to the Mode 1: Both Off (Doors will 1ocWunlock when you
mode selection you want. press the power door lock switch).
Mode 1: Both Off (Interior lamps will turn on or off at ~ Mode 2: Lockout Prevention Only (If you leave your
the same instant that a door is opened or closed). keys in the ignition and get outl the driver’s door, you
Mode 2: Delayed Illumination Only (Interior lamps will
stay on for
25 seconds after the doors are closed).
Mode 3: Exit Lighting Only (Interior lamps will come
on whenever you remove the ignition key). selection
you want.
won’t be able to lock the doors with the,power door lock
switch). Mode 3: Last Door Closed Locking Only (If the power
door lock switch is used to lock the, vehicle while any
door is open,
y0.u will hear three chimes. The doors will
Mode 4: Both On (This combines Mode 2 and 3). not lock until after all doors are closed).
Mode 4: Both On (This combines Mode 2 and 3).
ProCarManuals.com

LOCK (B): The only position in which you can remove
the key.
This locks your steering wheel, ignition and
automatic transmission.
If you have an automatic transmission, the ignition
switch can't be turned to
LOCK unless the shift lever is
in the PARK (P) position.
OFF (C): Unlocks the steering wheel, ignition and
automatic transmission, but does not
send electrical
power
to any accessories. Use this position if your
vehicle must be plashed or towed. A warning tone will
sound
if you open the driver's door when the ignition is
OFF and the key is in the ignition.
RUN (D): Position to which the switch returns after
you start your engine and release. the switch. The
switch stays in
the RUN position when the engine is
running. But even when the engine is not running, you
can use RUN to operate your electrical power
accessories and to display some instrument panel
START (E): Starts the engine. When the engine starts,
release the key. The ignition switch will return to RUN
for normal driving.
Note that even if the engine is not running,
ACC and
RUN allow you to operate your electrical accessories,
such as the radio .and ventilation fan.
I warning and indicator lights.
Key Release Button
If you have a manual
transmission, your
ignition lock has
a key
release button. You
must
press the button before
you can take your key out
of the ignition lock.
On manual transmission vehicles, turning the key
to
LOCK will lock the steering column and result
in a loss of ability to steer the vehicle. This could
cause a
collision. If you need to turn the engine
off while the vehicle is moving, turn the key only
to OFF. Don't press the key release button while
the vehicle
is moving.
ProCarManuals.com

Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow
you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When
the turn is finished, the lever will +
return automatically.
An arrow on the instrument
panel will flash in the
direction.
of the turn or lane
change.
As you signal a turn or a lane change, if the arrows don’t
flash but just ‘stay
on, a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses and,Circuit
Breakers” in the Index).
Headlarnp High/Low Beam Changer ’
.. -.
.;: , i.:. : . .. 1 g .- ..
To change the headlamps
from low beam to high or
high to low, pull the turn
signal lever all the way
toward you.
Then release it.
When
the high beams are
con, this light
on the
instrument panel also will
be on.
To signal a lane change, just raise or lower the lever
until the
mow starts to flash. Hold it there until you
complete
your lane change. The lever will return by
itself when you release it.
2-44
ProCarManuals.com

Lamps The main lamp control is a knob that works these lamps:
0 Headlamps
Taillamps
Parking Lamps
0 License Lamps
Sidemarker Lamps
0 Instrument Panel Lights
-'Q- , This setting turns on your headlamps and other
operating lamps.
Pg This setting turns on your parking lamps without
your headlamps.
Turn the hob to OFF to turn off the lamps.
Headlamps On Reminder
If you turn the ignition OFF and leave the lamps on, you
will hear a chime lasting up to 5 seconds. If the laws
are still on when you open the driver's door, the chime
will sound again.
ProCarManuals.com

Daytime Running Lamps (Option)
Daytime Running Lamps (DRL) can make it easier for
others
tu see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in.the
short periods after dawn and before sunset.
A light sensor on top of the instrument panel makes the
DRL work, so be sure it isn’t covered.
The
DRL system will make your front turn signal lamps
come on when:
The ignition is on,
The headlamp switch is OFF, and
The parking brake is released.
When
the DRL are on, only your front turn signal
lamps will be on. The taillamps, sidemarker and other
lamps won’t be on. Your instrument panel won’t be lit
up either.
When it’s dark enough outside, your front turn signal
lamps will
go out and your headlamps will come on.
The other lamps that come on with your headlamps will
also come on.
When it’s bright enough outside, the regular lamps will
go off, and your front turn signal lamps will come on.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Fog Lamps (Option)
Use your fog lamps for better vision in foggy or misty
conditions. Your parking lamps must be on or your fog
lamps won’t work.
SO To turn the fog lamps on, push the top of the fog
lamp switch,
Push the bottom of the switch to turn the
fog lamps off. A light on the switch will come on when
the fog
lamps are on.
Fog lamps will go off whenever your high beams come
on. When the high beams
go off, the fog lamps will
come
on again.
If your vehicle is equipped with Vehicle and Content
Theft-Deterrent System and your
fog lamp switch is
on,
the fog lamps may flash to indicate operation of
the Vehicle
and Content Theft-Deterrent System.
See “Vehicle and Content Theft-Deterrent System” in
the
Index.
2-52
ProCarManuals.com

Interior Lamps
Instrument Panel Brightness Control
This switch controls the brightness of your
instrument panel lights. Turn the switch to brighten
or
dim the lights. If you turn the switch all the way up your
courtesy lamps will come on.
Courtesy Lamps
When any door is opened, several interior lamps go on.
These lamps are courtesy lamps. They make it easier for
you to enter and leave your vehicle.
Courtesy lamps include the dome lamp and other
lamps
throughout the interior of your vehicle.
To prevent battery rundown, your interior lamps will be
disabled about
10 minutes after the ignition is turned to
OFFm The 10 minute timer will be restarted if you do any
of the following:
1. Turn the ignition on.
2. Open either door.
3.
4.
5.
Press any button on your Remote Lock
Control transmitter.
Turn the interior lamp switch from off to on.
Open the hatch.
Delayed Illumination (Option)
With delayed illumination, when you open a door, your
courtesy lamps will come
on and stay on for 25 seconds
after the doors
are closed. The 25 seconds is shortened
if the ignition is turned to
the RUN position or if the
power locks
are activated. To turn this feature on or off,
see “Feature Customization” in the Index.
Exit Lighting (Option)
With exit lighting, the interior lamps will come on when
you remove the key from the ignition to help you see
while exiting the vehicle. To turn
this feature on or off,
see “Feature Customization” in the Index.
..
ProCarManuals.com