1996 OLDSMOBILE AURORA key

Flash-To-Pass
I
If the headlamp switch is left on you’ll hear a warning
chime when you turn the ignition
off, remove the key
from the ignition and open the driver’s door.
Headlamp High/Low Beam
To change the headlamps
from low beam to high or
high to low, pull the turn
signal lever all the way
toward you. Then release it.
When the high beams are on, a light on the instrument
panel also will be on.
This feature lets you use your high-beariheadlamps to
signal .a driver
in front of you that you want to pass. It
works even if your headlamps are
off.
To use it, pull the turn signal lever toward you.
If your headlamps are
off, your high-beam headlamps
will turn on. They’ll stay on as long as you hold the
lever there. Release the lever to turn them
off.
If your headlamps are on, but on low beam, the system
works normally. Just pull the lever until it clicks. Your
headlamps will shift to high beam and stay there.
To
return to low beam, just pull the lever toward you.
If your headlamps are on, and on high beam, your
headlamps will switch to low beam.
To get back to high
beam, pull the lever toward you.
2-36
ProCarManuals.com

Exit Lighting
With this feature, the interior lamps will come on for
25 seconds after you remove the key from the ignition.
This will give
you time to find the door pull handle or
lock switches.
Illuminated Entry
Press the UNLOCK button on the key transmitter and
the interior courtesy lamps will come on and stay on for
up to a minute. The lamps will turn off immediately by
pressing the
LOCK button on the key transmitter,
starting the ignition or activating the power door locks.
Perimeter Lighting
When the UNLOCK button on the key transmitter is
pressed, the headlamps, parking lamps, back-up lamps
and cornering lamps will come on
if it is dark enough
outside according to the twilight sentinel.
This option can be programmed on or
off for each
transmitter.
To turn the feature offi
1. Press and hold the door lock switch throughout this
procedure. All doors will lock.
2. Press the panic button on the transmitter. Perimeter
lighting remains on at this time and the horn will
chirp two times.
3. Press the panic button on the key transmitter again.
Perimeter lighting is disabled and the horn will chirp
one time.
4. Release the door lock switch. The perimeter lighting
To turn the feature on:
option is now off.
1.
2.
3.
4.
Press and hold the door
lock switch throughout this
procedure. All doors will lock.
Press the panic button on the key transmitter.
Perimeter lighting remains off at this time and the
horn will chirp one time.
Press the panic button on the transmitter again.
Perimeter lighting is now enabled and the horn will
chirp two times.
Release the door
lock switch. The perimeter lighting
option is now on.
ProCarManuals.com

Heated Outside Rearview Mirror (Option)
When you operate the rear window defogger, a defogger
also warms the optional heated driver’s outside rearview
mirror to help clear it of ice and snow. This is an
electrochromic mirror that operates with the same
controls as the Electrochromic Daymight Rearview
Mirror, and it works the same way. See “Electrochromic
Daymight Rearview Mirror” earlier in this section.
Storage Compartments
Glove Box
Use the door key to lock and unlock the glove box.
To open, pull the latch release on the left side of the
glove box door.
Front Storage Armrest
The front armrest opens into a storage area. To open it,
lift the front edge. Inside you will find storage for
cassettes, compact discs and coins.
In front of the storage area is a cupholder. Press and
release the cupholder cover to open. Push the cupholder
forward
to lock it when in use. Press the cupholder back
to its recessed position when not in use.
111 down the bolster in the back seat to reveal cupholders
and
an armrest, which opens into a storage area.
ProCarManuals.com

Gages can indicate when there may be or is a problem
with one of your vehicle’s functions. Often gages and
warning lights work together to let you know when
there’s a problem with your vehicle.
When one of the warning lights comes on and stays on
when
you are driving, or when one of the gages shows
there may be a problem, check the section that tells you
what
to do about it. Please follow this manual’s advice.
Waiting to do repairs can be costly
-- and even
dangerous.
So please get to know your warning lights
and gages. They’re a big help.
Your vehicle may also have a driver information system
that works along with the warning lights and gages. See
“Driver Information System” in the Index.
Safety Belt Reminder Light
When the key is turned to RUN or START, a chime will
come on for about eight seconds to remind people to
fasten their safety belts.
The safety belt light will
also come on and stay on
for about
70 seconds. If the
driver’s belt is already
buckled, neither the chime
nor the light will come on.
ProCarManuals.com

Brake System Warning Light
Your Aurora’s hydraulic brake system is divided into
two parts. If one part isn’t working, the other part can
still work and stop you. For good braking, though, you
need both parts working well.
This light should come on when you
turn the ignition
key to START.
If it doesn’t
come on then, have it fixed
so it will be ready to warn
you
if there’s a problem. If
this warning light stays on
after you start the engine,
there could be a brake
problem. Have your brake
system inspected right away. If
the light and chime come
on while you are driving,
pull off the road and stop carefully. You may notice that
the pedal is harder to push. Or, the pedal may go closer
to the floor.
It may take longer to stop. If the light is still
on, have the vehicle towed
for service. (See “Towing
Your Vehicle” in the Index.)
Your brake system may not be working properly
if the brake warning light
is on. Driving with the
brake warning light on can lead to an accident.
If the light is still on after you’ve pulled off the
road and stopped carefully, have the vehicle
towed for service.
ProCarManuals.com

Parking Brake Indicator Light
PARK
Vehicles with hydraulic
brakes have a parking brake
indicator light. When the ignition
is on, this light will
come
on when you set your
parking brake. The light will
stay on if your
parking brake
doesn’t release fully. If you
try to drive
off with the
parking brake set, a chime will also come on until you
release the parking brake.
This light should also come on when you turn the
ignition key to START. If it doesn’t come on then, have
it fixed
so it will be ready to remind you if the parking
brake hasn’t released fully.
Anti-Lock Brake System Warning Light
LOCK
ANT‘- (@)
With the anti-lock brake system, this light will come
on when you start your
engine and may stay on for
several seconds. That’s
normal.
If the light stays on,
turn the ignition off. Or, if the light comes
on when you’re driving, stop as soon as possible and turn
the ignition off. Then start the engine again to reset the
system. If the light still stays on, or comes on again while
you’re driving, your Aurora needs service.
If the regular
brake system warning light isn’t on, you still have brakes, \
but you don’t have anti-lock brakes.
If the regular brake system
warning light is also on, you don’t have anti-lock brakes
and there’s a problem with your regular brakes. See “Brake
System Warning Light” earlier
in this part.
The anti-lock brake system warning light should come
on briefly when you turn the ignition key to
RUN. If the
light doesn’t come on then, have it fixed
so it will be
ready to warn you if there is a problem.
ProCarManuals.com

The following may prevent more serious damage to
your vehicle: I NOTICE:
If you keep driving your vehicle with this light
on, after
a while, your emission controls may not
work
as well, your fuel economy may not be as
good and your engine
may not run as smoothly.
This could lead to costly repairs that may not be
covered by your warranty.
This light should come on, as a check to show you it is
working, when the ignition
is on and the engine is not
running.
If the light doesn’t come on, have it repaired.
This light will also come
on during a malfunction in one
of two ways:
Light Flashing -- A misfire condition has been
detected.
A misfire increases vehicle emissions and
may damage the emission control system on your
vehicle. Retailer or qualified service center diagnosis
and service
is required.
Light On Steady -- An emission control system
malfunction has been detected on your vehicle.
Retailer or qualified service center diagnosis and
service may be required.
0 Reduce vehicle speed.
0 Avoid hard accelerations.
0 Avoid steep uphill grades.
If towing a trailer, reduce the amount of cargo being
hauled as soon as it is possible.
If the light stops flashing and remains on steady, see
“If
the Light Is On Steady” following.
If the light continues to flash, when
it is safe to do so,
stop the vehicle. Put your vehicle in PARK (P). Turn the
key off, wait at least 10 seconds and restart the engine.
If
the light remains on steady, see “If the Light Is On
Steady” following. If the light is still flashing, follow the
previous steps, and drive the vehicle to your retailer or
qualified service center for service.
ProCarManuals.com

m m. .pse
When the ignition is on, the Driver Information Center
can be used as a stopwatch. The display will show hours
and minutes. The elapsed time indicator will record up
to 100 hours, then it will reset to zero and continue
counting. Press ET, and the display will show the
amount
of time that has elapsed since the elapsed time
indicator was last reset (not including time the ignition
is
off), such as:
01:08 ELAPSED TIME
To reset elapsed time to zero, press RESET while the
elapsed time
is displayed.
Press DATE to display the date.
To change the date,
press DATE then RESET. The following display will
appear:
MONTH? XX/DD/YY
MM,
DD and YY represent the month, date and year
you currently have in your system. Check to make sure
your clock
is in the correct AM or PM mode. Notice that
each key has a number. Push the key to enter
the number. The first XX’s will flash until you enter the
first digit for the month. You don’t need to enter the
leading zero if the number is under
10. Press ENTER
after you’ve entered the month. The display will
change to:
DAY? MM/XX/YY
Set the day just as you set the month. After the day entry
is made, press ENTER, and the display will change to:
YEAR? MM/DD/XX
Set the year just as you set the month and day.
If a valid
date
is entered, the display will automatically exit to the
date mode and display the day
of the week, the month
and the date. If an invalid date is entered, the display
will return to MONTH? XX/DD/YY and you’ll need to
repeat the above steps.
After a battery reconnect (loss
of power), the display
will read CONFIRM TIME AND DATE.
?-79
ProCarManuals.com