1996 Mercury Villager wheel

Roadside Emergencies
259
*
[RE02800(ALL)03/95]
Jump-Starting
*
[RE02900(ALL)03/95]1.
Make sure that the jumper cables are not in the way of
moving engine parts, then start the booster vehicle. Run the
engine at a moderate speed.
*
[RE03000(ALL)03/95]2.
Let the discharged battery charge for a few minutes and then
start the disabled vehicle. It may take a couple of tries before
the vehicle starts. If the vehicle does not start after several
attempts, there may be a different problem.
*
[RE03100(ALL)03/95]3.
When both vehicles are running, let them idle for a few
minutes to charge the discharged battery.
*
[RE03200(ALL)03/95]
Removing jumper cables
*
[RE03300(ALL)03/95]1.
Always remove the jumper cables in the reverse order.
Remove the negative (s) end of the jumper cable from the
metallic surface on the engine or frame of the disabled
vehicle.
*
[RE03400(ALL)05/95]2.
Remove the negative (s) cable from the booster battery.
*
[RE03500(ALL)06/95]3.
Remove the positive (+) cable from the booster battery.
*
[RE03600(ALL)05/95]4.
Remove the other end of the positive (+) cable from the
discharged battery.
[RE03750(ALL)02/95]
If you need to replace your battery, seeBatteryin theServicing
Your Villagerchapter.
*
[RE03800(ALL)01/93]
Changing a Flat Tire
*
[RE03900(ALL)01/95]
If you get a flat tire while you are driving, do not apply the
brake heavily. Instead, gradually decrease the speed. Hold the
steering wheel firmly and slowly move to a safe place on the
side of the road. Park on a level spot, turn off the ignition, set
the parking brake, and turn on the hazard flashers.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

260
*
[RE04000(ALL)03/95]
The Temporary Spare Tire
*
[RE04100(ALL)03/94]
Your vehicle has a temporary spare tire (unless you ordered the
optional full-size spare tire). This spare tire is smaller than a
regular tire and is designed for emergency use only. Use it only
when you get a flat tire and replace it as soon as you can. This
spare tire is marked with the words TEMPORARY USE ONLY
so that you can easily identify it.
*
[RE04200(ALL)01/93]
RWARNING
If you use the temporary spare tire continuously or do
not follow these precautions, the tire could fail, causing
you to lose control of the vehicle, possibly injuring
yourself or others.
*
[RE04300(ALL)02/95]
When you drive with the temporary spare tire, DO NOT:
*
[RE04500(ALL)02/95]
n
exceed 50 mph (80 km/h) under any circumstances
*
[RE04600(ALL)01/93]
n
load your vehicle so that it is heavier than the maximum
vehicle load rating listed on the tire decal
*
[RE04700(ALL)01/93]
n
tow a trailer
*
[RE04800(ALL)01/93]
n
use tire chains
*
[RE04900(ALL)01/93]
n
try to repair the temporary spare tire or remove it from its
wheel
*
[RE05000(ALL)01/93]
n
use the wheel for any other type of vehicle
*
[RE05100(ALL)01/93]
n
drive through an automatic car wash. Because the temporary
spare tire is smaller than a conventional tire, it reduces the
ground clearance. Your vehicle may get caught in the rails
and it could be damaged.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

262
*
[RE05900(ALL)09/93]
10-1/2 pica
art:0040172-B
The spare tire in the lowered position
*
[RE06000(ALL)01/93]4.
Continue to turn the hex nut counterclockwise until the
spare tire retainer can be seen for removal.
*
[RE06100(ALL)01/93]5.
Remove the retainer from the center of the wheel. It may be
necessary to lift one end of the tire to disengage the retainer.
*
[RE06200(ALL)09/93]
10-1/2 pica
art:0040173-B
Removing the spare tire retainer
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

Roadside Emergencies
263
*
[RE06300(ALL)01/93]
Stowing the spare tire
[RE06400(ALL)04/95]1.
To raise the tire to the stowed position, lay the tire on the
ground with the inboard side facing up. Install the retainer
through the wheel center and slide the tire under the vehicle.
Fit the hex-shaped end of the wheel lug wrench over the hex
nut in the floor of the cargo area. Turn the wheel lug
wrench clockwise until the tire is raised to its original
position underneath the vehicle.
[RE06500(ALL)01/93]
NOTE: The lug wrench ratchets when the tire is raised to the
stowed position. It will not allow you to over-tighten.
*
[RE06600(ALL)01/93]2.
Check for proper seating against the underbody supports
and retighten if necessary.
*
[RE06700(ALL)05/95]
RWARNING
Make sure spare tires and jacking equipment are stowed
and secured in the proper storage location.
*
[RE06800(ALL)03/95]
Preparing to Change the Tire
*
[RE06900(ALL)05/94]
You should only raise your vehicle with a jack properly placed
at the front or rear jacking points.
*
[RE07000(ALL)06/95]1.
Make sure that your vehicle will not move or roll. Put the
gearshift lever in P (Park). Set the parking brake and block
the wheel Ð in both directions Ð that is diagonally opposite
the tire that you are changing.
*
[RE07100(ALL)06/95]
RWARNING
When one of the front wheels is off the ground, the
transaxle alone will not prevent the vehicle from moving
or slipping off the jack, even if the vehicle is in P (Park).
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

264
*
[RE07200(ALL)01/93]
RWARNING
To prevent the vehicle from moving when you change a
tire, be sure the parking brake is set, then block (in both
directions) the wheel that is diagonally opposite (other
side and end of the vehicle) to the tire being changed.
*
[RE07300(ALL)01/93]
RWARNING
If the vehicle slips off the jack, you or someone else
could be seriously injured.
[RE07400(ALL)01/93]2.
Get out the spare tire and jack. See previous section for
instructions on spare tire removal. The jack is located in the
rear storage compartment in the right door panel of the
cargo area. You will have to unfasten the jack before
removing it as shown in the illustration.
[RE07450(ALL)09/93]
NOTE: All occupants should be out of the vehicle while it is
on the jack.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

Roadside Emergencies
265
[RE07500(ALL)09/93]
24 pica art:0040170-C
Jack storage location
*
[RE07600(ALL)01/93]3.
Insert the tapered end of the jack handle behind the wheel
cover of the tire to be changed and gently pry it off. When
you want to replace the wheel cover, simply align the valve
stem to the slot in the cover and press it back on.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

266
[RE07700(ALL)06/95]
17-1/2 pica
art:0040177-D
Removing the wheel cover
[RE07800(ALL)01/93]
If you have the optional cast-aluminum wheel covers, remove
the wheel cap to gain access to the lug nuts. Insert the tapered
end of the jack handle behind the notch in the wheel cap and
gently pry it off. To replace it, press it back on. You must line
up the raised circle on the back of the wheel cap with the
indented area on the wheel in order to press the wheel cap on.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

Roadside Emergencies
267
[RE07900(ALL)09/93]
13-1/2 pica
art:0040181-B
Removing the optional wheel cap
*
[RE08000(ALL)02/95]4.
Fit the hex-shaped end of the lug wrench over the wheel lug
nuts and loosen them one-half turn (counterclockwise). Do
not remove the wheel lug nuts until you raise the tire off the
ground.
*
[RE08100(ALL)02/95]
If your vehicle has the optional locking lug nuts, you must
use the lug nut removal tool provided with your vehicle's
tool kit.
*
[RE08200(ALL)02/95]
7-1/2 pica art:0040182-A
Anti-theft lug nut
*
[RE08300(ALL)01/93]5.
Fit the jack under the proper jacking point indicated by the
notch in the bottom of the door frame panel.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996