1996 Mercury Sable change time

71
[ST12300(ALL)02/95]
Guarding Against Exhaust Fumes
*
[ST12400(ALL)02/95]
Carbon monoxide, although colorless and
odorless, is present in exhaust fumes. Take
precautions to avoid its dangerous effects.
*
[ST12500(ALL)01/95]
RWARNING
Never idle the engine in closed areas.
Never sit in a parked or stopped
vehicle for more than a short period
of time with the engine running.
Exhaust fumes, particularly carbon
monoxide, may build up. These
fumes are harmful and could kill
you.
*
[ST12600(ALL)01/95]
RWARNING
If you ever smell exhaust fumes of
any kind inside your vehicle, have
your dealer inspect and fix your
vehicle immediately. Do not drive if
you smell exhaust fumes. These
fumes are harmful and could kill
you.
*
[ST12700(ALL)01/95]
Have the exhaust and body ventilation systems
checked whenever:
*
[ST12800(ALL)02/95]
q
your vehicle is raised for service
*
[ST12900(ALL)02/95]
q
the sound of the exhaust system changes
*
[ST13000(ALL)01/95]
q
your vehicle has been damaged in a collision
*
[ST13200(ALL)01/95]
Improve your ventilation by keeping all air inlet
vents clear of snow, leaves, and other debris.
File:fcsts.ex
Update:Wed Dec 20 09:34:24 1995

97 [IP05025(ALL)03/95]
To turn your EATC on, press the AUTO button
or any of the six manual override buttons along
the bottom of the control.
[IP05125(ALL)03/95]
To turn your EATC off, press the OFF button.
When the system is off, the Display window will
be blank (dark).
[IP05225(ALL)02/95]
If you select AUTO, the system will
automatically determine fan speed and airflow
location. If a manual override button is selected,
your selection determines airflow location only.
Fan speed remains automatic unless you
override it by pressing either side of the FAN
speed button located at the extreme left of the
control panel.
[IP05325(ALL)03/95]
To change the temperature, select any
temperature between65ÊF (18ÊC) and 85ÊF (29ÊC)
by pressing the
aor
bside of the TEMP
button. The EATC will display the selected
temperature.
[IP05400(ALL)04/95]
To change the temperature display from
Farenheit to Celsius, depress the MAX A/C and
VF-DEF at the same time and hold them
down for about a second. To change back to the
original setting, repeat the process. If the battery
is disconnected, the display will revert to
Fahrenheit and must be reset to Celsius.
[IP05425(ALL)03/95]
If you want continuous maximum cooling, press
the
bside of the TEMP button until60ÊF (16ÊC)
is shown in the display window. Your EATC
will cool at maximum and disregard the60ÊF
(16ÊC) setting until you select a warmer
temperature with the
aside of the TEMP
button. If you want continuous maximum
heating, press the
aside of the TEMP button
until90ÊF (32ÊC) isshown in the display
window. Your EATC will provide maximum
heat regardless of the90ÊF (32ÊC)setting until
you select a cooler temperature with the
bside
of the TEMP button.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

107 [IP25250(ALL)02/89]
To change your headlamps from low to high
beam, push the turn signal lever away from you.
To change them back to low beam, pull the
lever toward you.
*
[IP25300(ALL)03/93]
For more information about how the high beam
headlamps work, seeSteering column controlsin
the Index.
%*
[IP25605(ALL)01/95]
Daytime Running Light System
[IP25610(ALL)03/95]
(Canadian and fleet vehicles only)
*
[IP25615(ALL)03/95]
The Daytime Running Light (DRL) system is
designed to turn the high beam headlamps on,
with a reduced light output and without
illuminating the high beam indicator lamp in the
instrument panel. The DRL system operates
when all of the following conditions are met:
*
[IP25620(ALL)03/95]
q
The vehicle is ªrunning.º
*
[IP25625(ALL)01/95]
q
The vehicle has a fully released parking
brake.
*
[IP25630(ALL)03/95]
q
The headlamp system is in the OFF position.
*
[IP25635(ALL)01/95]
NOTE: If you have a vehicle with an
automatic lighting system, the DRL
system is active until the automatic
system turns on the headlamps.
*
[IP25636(ALL)10/94]
NOTE: The high beam indicator will not turn
on in the flash-to-pass mode during
nighttime driving.
[IP25637(ALL)01/95]
You may notice that the lights flicker when the
vehicle is turned on or off. This is a normal
condition.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

97 [IP05025(ALL)03/95]
To turn your EATC on, press the AUTO button
or any of the six manual override buttons along
the bottom of the control.
[IP05125(ALL)03/95]
To turn your EATC off, press the OFF button.
When the system is off, the Display window will
be blank (dark).
[IP05225(ALL)02/95]
If you select AUTO, the system will
automatically determine fan speed and airflow
location. If a manual override button is selected,
your selection determines airflow location only.
Fan speed remains automatic unless you
override it by pressing either side of the FAN
speed button located at the extreme left of the
control panel.
[IP05325(ALL)03/95]
To change the temperature, select any
temperature between65ÊF (18ÊC) and 85ÊF (29ÊC)
by pressing the
aor
bside of the TEMP
button. The EATC will display the selected
temperature.
[IP05400(ALL)04/95]
To change the temperature display from
Farenheit to Celsius, depress the MAX A/C and
VF-DEF at the same time and hold them
down for about a second. To change back to the
original setting, repeat the process. If the battery
is disconnected, the display will revert to
Fahrenheit and must be reset to Celsius.
[IP05425(ALL)03/95]
If you want continuous maximum cooling, press
the
bside of the TEMP button until60ÊF (16ÊC)
is shown in the display window. Your EATC
will cool at maximum and disregard the60ÊF
(16ÊC) setting until you select a warmer
temperature with the
aside of the TEMP
button. If you want continuous maximum
heating, press the
aside of the TEMP button
until90ÊF (32ÊC) isshown in the display
window. Your EATC will provide maximum
heat regardless of the90ÊF (32ÊC)setting until
you select a cooler temperature with the
bside
of the TEMP button.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

107 [IP25250(ALL)02/89]
To change your headlamps from low to high
beam, push the turn signal lever away from you.
To change them back to low beam, pull the
lever toward you.
*
[IP25300(ALL)03/93]
For more information about how the high beam
headlamps work, seeSteering column controlsin
the Index.
%*
[IP25605(ALL)01/95]
Daytime Running Light System
[IP25610(ALL)03/95]
(Canadian and fleet vehicles only)
*
[IP25615(ALL)03/95]
The Daytime Running Light (DRL) system is
designed to turn the high beam headlamps on,
with a reduced light output and without
illuminating the high beam indicator lamp in the
instrument panel. The DRL system operates
when all of the following conditions are met:
*
[IP25620(ALL)03/95]
q
The vehicle is ªrunning.º
*
[IP25625(ALL)01/95]
q
The vehicle has a fully released parking
brake.
*
[IP25630(ALL)03/95]
q
The headlamp system is in the OFF position.
*
[IP25635(ALL)01/95]
NOTE: If you have a vehicle with an
automatic lighting system, the DRL
system is active until the automatic
system turns on the headlamps.
*
[IP25636(ALL)10/94]
NOTE: The high beam indicator will not turn
on in the flash-to-pass mode during
nighttime driving.
[IP25637(ALL)01/95]
You may notice that the lights flicker when the
vehicle is turned on or off. This is a normal
condition.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

173 [AS11400(ALL)02/95]
q
Using the ªTUNEº function
[AS11525(ALL)02/95]
You can change the frequency up or down
one increment at a time by pressing and
releasing either the right (
a) or left (
b) side
of the ªTUNEº or ªTUNE/DISCº button. To
change frequencies quickly, press and hold
down either the right or left side of the
button.
*
[AS11700(ALL)02/95]
q
Using the ªSEEKº function
[AS11825(ALL)02/95]
Press the right (
a) side of the ªSEEKº
button to select the next listenable station up
the frequency band. Press the left (
b) side of
the button to select the next listenable station
down the frequency band. By pressing and
holding the button, listenable stations can be
passed over to reach the desired station.
*
[AS12200(ALL)01/95]
q
Using the ªSCANº function
*
[AS12325(ALL)04/95]
Pressing the ªSCANº button will begin the
scan mode up the frequency band, stopping
on each listenable station for approximately
five seconds. The band indicator (AM, FM1,
FM2) flashes during scan operation.
*
[AS12340(ALL)02/95]
To stop the scan mode on the presently
sampled station, press the ªSCANº button
again.
*
[AS12700(ALL)02/95]
q
Setting the Station Memory Preset buttons
*
[AS12850(ALL)02/95]
Your radio is equipped with 6 station
memory buttons. These buttons can be used
to select up to 6 preset AM stations and 12
FM stations (6 in FM1 and 6 in FM2).
File:fcass.ex
Update:Wed Dec 20 09:30:38 1995

179
*
[AS17200(ALL)01/95]
q
Using the ªSCANº function with your
cassette tape player
[AS17325(ALL)02/95]
Press the ªSCANº button to begin the
forward scan mode on the tape currently
playing, stopping on each tape selection for
approximately an eight-second sampling
(display flashes ªSCANº).
[AS17345(ALL)04/95]
To stop the scan mode on the presently
sampled tape selection press ªSCANº a
second time.
[AS17348(ALL)02/95]
How to change the side of the tape being
played
[AS17350(ALL)02/95]
The alternate side of the tape can be selected at
any time by pressing the ªSIDE 1-2º button.
*
[AS17400(ALL)02/95]
How to eject the tape
[AS17525(ALL)04/95]
To stop the tape and eject the cassette, press the
ªEJº button. The radio will resume playing if the
power is on. The tape cartridge can be ejected
with radio power (and/or ignition) on or off.
*
[AS17550(ALL)01/95]
How to store the tape
[AS17575(ALL)04/95]
Press the ªAMº or ªFMº button (or ªCDº, if
equipped) to stop the tape player and resume
radio play (or CD-DJ).
*
[AS17600(ALL)02/95]
Using the DolbyHB noise reduction feature
*
[AS17700(ALL)02/95]
NOTE: Noise reduction system manufactured
under license from Dolby Labs
Licensing Corporation. ªDolbyº and
double-D symbol are trademarks of
Dolby Laboratories Licensing
Corporation.
*
[AS17825(ALL)04/95]
Push thekbutton to activate Dolby B Noise
Reduction. Push again to deactivate.
File:fcass.ex
Update:Wed Dec 20 09:30:38 1995

225
*
[RE08400(ALL)11/94]
RWARNING
When one of the front wheels is off
the ground, the transaxle alone will
not prevent the vehicle from moving
or slipping off the jack, even if the
vehicle is in P (Park). To prevent the
vehicle from moving when you
change a tire, block (in both
directions) the wheel that is
diagonally opposite to the tire being
changed. If the vehicle slips off the
jack, you or someone else could be
seriously injured.
*
[RE08800(ALL)02/95]
2. Get out the spare tire and jack.
*
[RE08850(ALL)05/94]
RWARNING
To avoid injury, never run the engine
with one wheel off the ground when
changing a tire, or at any other time.
The wheel still on the ground could
cause the vehicle to move.
[RE08900(ALL)02/93]
3. Remove wheel covers or aluminum wheel
ornaments with the tapered end of a wheel
nut wrench. Insert the handle of the wrench
between the wheel and ornament and twist
it against the inner wheel cover flange.
*
[RE09200(ALL)01/95]
4. Loosen each wheel lug nut one-half turn
counterclockwise, but do not remove them
until the tire is raised off the ground. You
should pull up on the handle rather than
push to develop maximum force to loosen
wheel lug nuts. SeeAnti-Theft Wheel Lug
Nutslater in this chapter for information on
removing anti-theft lug nuts.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995