1996 Mercury Sable light

111 [IP30700(ALL)11/94]
To dim the instrument panel lights, rotate the
thumbwheel down. To turn on the interior
lights, turn the thumbwheel all the way up. The
interior lights also come on when any side door
or the liftgate is opened.
[IP30925(ALL)03/95]
Dome Lamps
[IP30950(ALL)03/95]
The front dome lamp is located overhead
between the driver and front passenger seats.
However, if your vehicle is equipped with a
power moon roof, the dome lamp is located
behind the moon roof.
[IP30975(ALL)11/94]
In the wagon, the rear dome lamp is located
overhead near the rear seating positions.
[IP31025(ALL)02/95]
one third page art:0001410-A
The dome/map lamp
[IP31050(ALL)03/95]
Turn the map lamps on and off with the
switches on the lamp. The dome lamp
illuminates when any door is opened. If either
the driver's or passenger's front door is opened
using the outside door handle, the light will
remain on for 25 seconds after the door has been
shut. If any other door is opened or if either of
the front doors is opened using the inside
handle, the lamp will immediately turn off when
the door is closed.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

113 [IP31200(ALL)04/95]
Cleaning the Interior Lamps
*
[IP31300(ALL)04/95]
Your interior dome lamps and map lamps are
plastic and should be cleaned with a mild
detergent diluted in water. Rinse them with clear
water.
%*
[IP31400(ALL)01/95]
Battery Saver
[IP31500(ALL)11/94]
When the ignition is turned off, the vehicle will
turn off battery voltage to the interior lights
after 40 minutes.
*
[IP31600(ALL)02/95]
This will prevent draining of the battery if those
lights have been left on inadvertently or if a
door is not completely closed. Battery voltage to
these lamps will be restored when the outside
front door handles are lifted, the keyless entry
keypad is used, the remote entry transmitter is
used, any door is opened, the trunk is opened,
or the ignition key is turned to the ON position.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

115
Steering Column Controls
*
[SC00400(ALL)01/95]
The controls on the steering column and wheel
are designed to give you easy access to the
controls while you are driving.
%
*
[SC00500(ALL)01/95]
The Turn Signal Lever
*
[SC00600(ALL)01/95]
You can use the turn signal lever on the left side
of the steering column to:
[SC00700(ALL)03/95]
q
operate the turn signals
*
[SC00800(ALL)01/95]
q
turn the high beams on/off
*
[SC00900(ALL)01/95]
q
flash the lights
*
[SC01000(ALL)01/95]
q
turn the windshield wipers and washer
on/off
%*
[SC01100(ALL)01/95]
Turn Signals
*
[SC02201(ALL)03/95]
Move the lever up to signal a right turn. Move
it down to signal a left turn. The corresponding
indicator light in the instrument cluster will
flash.
*
[SC02401(ALL)03/95]
If the turn signal stays on after you turn, move
the lever back to the center (off) position.
*
[SC02451(ALL)03/95]
For lane changes, move the lever far enough to
signal but not to latch. The lever will return to
the off position when you release it.
%*
[SC02800(ALL)03/95]
High Beams
*
[SC03100(ALL)08/95]
To turn on the high beams, turn the headlamp
control knob to the headlamp ON position and
push the turn signal lever away from you until
it latches. When the high beams are ON, the
high beam indicator light on the instrument
panel comes on.
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995

116
*
[SC03200(ALL)03/95]
To turn off the high beams, pull the lever
toward you until it latches. The high beam
indicator light turns off.
%*
[SC03300(ALL)03/95]
Flashing the Lights
*
[SC03400(ALL)08/95]
To flash the headlamps, pull the lever toward
you for a moment and then release it. The
headlamps will flash whether the headlamp
knob is on or off.
[SC03450(ALL)04/95]
one third page art:0001411-B
The turn signal lever
%*
[SC03500(ALL)03/95]
Windshield Wipers and Washer
*
[SC03600(ALL)03/95]
To turn on the windshield wipers, the ignition
key must be turned to the ON or ACC position.
[SC03900(ALL)05/94]
Turn the knob on the end of the turn signal
lever away from you to activate the wipers. The
first seven detents are interval wipe positions,
the eighth detent is the LO position, and the
ninth detent is the HI position.
*
[SC04000(ALL)01/95]
To turn the wipers off, turn the knob toward
you to the OFF position.
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995

121
malfunction. Therefore, use only properly
installed FCC approved radio transmitting
equipment in your vehicle.
[SC08000(ALL)11/94]
one third page art:0001399-B
The speed control buttons on the steering wheel
*
[SC08200(ALL)03/95]
To set the speed control:
[SC08400(ALL)11/94]
1. Press and release the ON switch. The
CRUISE indicator light in the instrument
cluster will illuminate to indicate that speed
control is in a standby mode.
*
[SC08500(ALL)04/95]
2. Accelerate to the desired speed above
30 mph (50 km/h) using the accelerator
pedal.
*
[SC08800(ALL)03/95]
3. Press the SET ACCEL switch and release it
immediately to set your speed. If you keep
this switch pressed, your speed will continue
to increase.
*
[SC08900(ALL)03/95]
4. Take your foot off the accelerator pedal.
Your vehicle will maintain the speed you set.
*
[SC09000(ALL)01/95]
If you drive up or down a steep hill, your
vehicle may momentarily slow down or speed
up, even though the speed control is on. This is
normal.
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995

123 [SC09350(ALL)03/95]
NOTE: When driving uphill, especially with a
heavy load, you may notice your speed
decreasing even if you have the speed
control set. If the speed drops more
than 8 to 14 mph (13-23 km/h) it is
normal for the automatic speed control
feature to be cancelled. You may need
to use the accelerator pedal to help
your vehicle maintain the selected
speed when driving up steep grades.
%*
[SC09400(ALL)01/95]
Resetting the Speed Control
*
[SC09410(ALL)03/95]
To reset the speed control to alower speed, use
one of the following procedures:
*
[SC09415(ALL)03/95]
q
COASTÐ Press and hold the COAST switch.
Release the switch when the vehicle slows
down to the desired speed.
*
[SC09420(ALL)03/95]
q
Lightly tap the brake pedal. When the vehicle
attains the desired speed, press the SET
ACCEL switch and release it immediately.
[SC09425(ALL)11/94]
q
TAP-DOWNÐ Press and then quickly
release the COAST switch. Each time you
ªtapº the switch, the set speed will decrease
by 1 mph (1.6 km/h). Multiple taps will
cause the set speed to decrease in increments
of 1 mph (1.6 km/h). For example, if the
current set speed is 60 mph (96 km/h) 5 taps
of the COAST switch will decrease the
vehicle speed and SET it at 55 mph
(88 km/h).
*
[SC09430(ALL)04/95]
If vehicle speed is reduced below 30 mph
(50 km/h) by any of the above methods, then
you must manually accelerate to a speed over
30 mph (50 km/h) and reset the system.
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995

128 %
*
[FV04251(ALL)03/95]
Using the Keyless Entry System
(If equipped)
*
[FV04301(ALL)02/95]
If your vehicle has the keyless entry system, you
can lock or unlock the vehicle doors without
using a key. The buttons for the system are near
the outside door handle on the driver's side. See
alsoRemote Entry Systemwhich follows this
description.
[FV04351(ALL)02/95]
one third page art:0000482-C
Keyless entry buttons
*
[FV04401(ALL)02/95]
When you bought your vehicle, you were given
a computer code that operates the system for
your vehicle. For your convenience, we have
duplicated this code in two places.
*
[FV04451(ALL)02/95]
The code is:
*
[FV04501(ALL)02/95]
q
on your owner's wallet card found in the
glove compartment
*
[FV04551(ALL)02/95]
q
taped to the computer module
[FV04601(ALL)03/95]
When you use this entry system, the illuminated
entry system turns on the interior lights for 25
seconds and the buttons on the keypad light up
for 5 seconds. Do not push the buttons with a
key, ballpoint pen, pencil or any other hard
object. These objects could damage the buttons.
File:fcfvs.ex
Update:Wed Dec 20 09:39:11 1995

130 %
*
[FV05350(ALL)02/95]
Unlocking the doors with the keyless entry
system
*
[FV05401(ALL)02/95]
You must unlock the driver's door before you
unlock any of the other doors. If you let more
than five seconds pass between pressing
numbers, the system shuts down, and you have
to enter the code again. The system has shut
down if the keypad light is out. If the keyless
entry system does not work properly, use the
key or transmitter(s) to lock and unlock the
doors.
*
[FV05450(ALL)02/95]
1. To unlock the driver's door, enter the factory
code or your personal code. All codes have
five numbers. After you press the fifth
number, the driver's door unlocks.
[FV05500(ALL)04/95]
2. To unlock the passenger's door(s) and
liftgate (wagon), press the 3/4 button within
five seconds of unlocking the driver's door
or re-enter the code to open the driver's
door, then press 3/4.
[FV05525(ALL)03/95]
3. To open the trunk (sedan) or unlock the
liftgate (wagon), enter the five-digit factory
code, then press the 5/6 button within 5
seconds.
*
[FV05550(ALL)02/95]
Locking the doors with the keyless entry
system
*
[FV05601(ALL)02/95]
Along with unlocking your doors, you can use
the keyless entry system to lock the doors. You
can also use the Autolock feature to
automatically lock the doors after you get in the
vehicle.
*
[FV05650(ALL)02/95]
To lock all of the doors, press 7/8 and 9/0 at
the same time. It is not necessary to first enter
the keypad code. This will arm your factory
installed anti-theft system, if so equipped.
File:fcfvs.ex
Update:Wed Dec 20 09:39:11 1995