1996 Mercury Sable light

65
*
[ST09360(ALL)02/95]
4. Turn the key to the START position
(cranking) until the engine starts. Allow the
key to return to the ON position after the
engine has started.
*
[ST09370(ALL)02/95]
If you have difficulty in turning the key,
rotate the steering wheel slightly because it
may be binding.
%*
[ST09375(ALL)04/95]
For a cold engine:
*
[ST09381(ALL)04/95]
q
At temperatures10ÊF (-12ÊC) andbelow:If
the engine does not start infifteen (15)
secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you
do not flood the engine, then try again.
*
[ST09385(ALL)04/95]
q
At temperaturesabove10ÊF(-12ÊC):If the
engine does not start infive (5) secondson
the first try, turn the key to OFF, wait
approximately ten (10) seconds so you do not
flood the engine, then try again.
%*
[ST09387(ALL)04/95]
For a warm engine:
*
[ST09390(ALL)04/95]
q
Do not hold the key in the START position
for more thanfive (5) secondsat a time. If
the engine does not start within five (5)
seconds on the first try, turn the key to the
OFF position. Wait a few seconds after the
starter stops, then try again.
*
[ST09400(ALL)04/95]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter or flood the engine.
*
[ST09410(ALL)04/95]
After you start the engine, let it idle for a few
seconds. Keep your foot on the brake pedal and
put the gearshift lever in gear. Release the
parking brake. Slowly release the brake pedal
and drive away in the normal manner.
File:fcsts.ex
Update:Wed Dec 20 09:34:24 1995

66 [ST09420(ALL)11/94]NOTE: Your vehicle is equipped with an
automatic transaxle and has an
interlock that prevents you from
shifting out of P (Park) unless your
foot is on the brake pedal.
*
[ST09480(ALL)04/95]
If the engine does not start after two attempts:
*
[ST09492(ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST09494(ALL)04/95]
2. Press the accelerator all the way to the floor
and hold it.
*
[ST09496(ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST09497(ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST09498(ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST09500(ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
%*
[ST10200(ALL)04/95]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs high. These faster
engine speeds will make your vehicle move
slightly faster than its normal idle speed. It
should, however, slow down after a short time.
If it does not, have the idle speed checked.
File:fcsts.ex
Update:Wed Dec 20 09:34:24 1995

70
*
[ST11800(ALL)03/95]
RWARNING
If you see or smell fuel, do not reset
the switch or try to start your vehicle.
You could injure yourself or others.
Have all the passengers get out of
the vehicle and call the local fire
department or a towing service.
*
[ST11900(ALL)03/95]
If your engine cranks but does not start after a
collision or substantial jolt:
*
[ST11950(ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST12000(ALL)03/95]
2. Check under the vehicle for leaking fuel.
*
[ST12050(ALL)01/95]
3. If you do not see or smell fuel, push the red
reset button on the fuel pump shut-off
switch down.
*
[ST12100(ALL)03/95]
4. Turn the ignition key to the ON position for
a few seconds, then turn it to the OFF
position.
*
[ST12150(ALL)03/95]
5. Check under the vehicle again for leaking
fuel.If you see or smell fuel, do not start
your vehicle again.If you do not see or
smell fuel, you can try to start your vehicle
again.
*
[ST12200(ALL)03/95]
6. Check all vehicle warning lights before
driving the vehicle.
*
[ST12225(ALL)01/95]
Pushing
*
[ST12250(ALL)11/94]
Vehicles with automatic transaxles cannot be
started by pushing. Follow the directions under
If Your Vehicle Needs a Jump-Startin theRoadside
EmergenciesChapter.
File:fcsts.ex
Update:Wed Dec 20 09:34:24 1995

91
Instrument Panel Controls
%*
[IP00400(ALL)04/95]
The main controls for the climate control system,
clock, and radio are in the oval Integrated
Control Panel on the instrument panel.
[IP00410(ALL)04/95]
The controls for the lights and climate control air
registers are also on the instrument panel.
*
[IP00420(ALL)03/95]
Clean the instrument panel lens and woodtone
trim with a soft cloth and a glass cleaner. Do
not use paper towel or any abrasive cleaner to
clean either the lens or the woodtone trim as
these may cause scratches.
%*
[IP00430(ALL)04/95]
NOTE: Any cleaner or polish that increases the
gloss (shine) of the upper part of the
instrument panel should be avoided.
The dull finish in this area is to help
protect the driver from undesirable
windshield reflection.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

106
%*
[IP23600(ALL)01/95]
The Interior and Exterior Lights
%*
[IP23700(ALL)01/95]
Turning On the Exterior Lights
[IP23800(ALL)08/95]
To turn on your headlamps, parking lamps, side
markers, and tail lamps, use the knob that is to
the left of the steering wheel.
[IP24200(ALL)08/95]
one third page art:0000695-C
The knob for the headlamps, parking lamps, and tail lamps
[IP24500(ALL)08/95]
To turn on the parking lamps, side markers, and
tail lamps, turn the knob to ªPº or the first
position.
[IP24600(ALL)08/95]
To turn on the headlamps, parking lamps, side
markers, and tail lamps, turn the knob to the
second position.
[IP25200(ALL)03/95]
one third page art:0001411-B
Turning on the high beams
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

107 [IP25250(ALL)02/89]
To change your headlamps from low to high
beam, push the turn signal lever away from you.
To change them back to low beam, pull the
lever toward you.
*
[IP25300(ALL)03/93]
For more information about how the high beam
headlamps work, seeSteering column controlsin
the Index.
%*
[IP25605(ALL)01/95]
Daytime Running Light System
[IP25610(ALL)03/95]
(Canadian and fleet vehicles only)
*
[IP25615(ALL)03/95]
The Daytime Running Light (DRL) system is
designed to turn the high beam headlamps on,
with a reduced light output and without
illuminating the high beam indicator lamp in the
instrument panel. The DRL system operates
when all of the following conditions are met:
*
[IP25620(ALL)03/95]
q
The vehicle is ªrunning.º
*
[IP25625(ALL)01/95]
q
The vehicle has a fully released parking
brake.
*
[IP25630(ALL)03/95]
q
The headlamp system is in the OFF position.
*
[IP25635(ALL)01/95]
NOTE: If you have a vehicle with an
automatic lighting system, the DRL
system is active until the automatic
system turns on the headlamps.
*
[IP25636(ALL)10/94]
NOTE: The high beam indicator will not turn
on in the flash-to-pass mode during
nighttime driving.
[IP25637(ALL)01/95]
You may notice that the lights flicker when the
vehicle is turned on or off. This is a normal
condition.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

108
*
[IP25638(ALL)01/95]
RWARNING
When the Daytime Running Light
(DRL) system is active the tail lamps,
parking lamps and side markers on
your vehicle will not be illuminated.
It is necessary to turn on your
headlamps at dusk. Failure to do so
may result in a collision, possibly
injuring yourself and others.
%*
[IP25640(ALL)04/95]
Cleaning the Exterior Lamps
*
[IP25650(ALL)04/95]
Do not use dry paper towel, chemical solvents
or abrasive cleaners to clean the lamps, as these
may cause scratches or crack the lamps.
%*
[IP26600(ALL)02/95]
Setting the Autolamp Delay System
(If equipped)
*
[IP26700(ALL)02/95]
The autolamp sets the headlamps to turn on and
off automatically. You can use the autolamp to:
*
[IP26800(ALL)01/95]
q
turn on the lamps automatically at night
*
[IP26900(ALL)01/95]
q
turn off the lamps automatically during
daylight
[IP27000(ALL)11/94]
q
keep the lamps on for up to three minutes
after you turn the ignition to the OFF
position.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

109 [IP27100(ALL)02/95]
one third page art:0000693-C
The autolamp system on the left side of the instrument
panel
*
[IP27400(ALL)01/95]
To set the autolamp:
*
[IP27450(ALL)08/95]
1. Make sure the headlamp knob is in the OFF
position. If the switch for the headlamps is
ON, you cancel the autolamp.
*
[IP27550(ALL)01/95]
2. Turn the ignition key to ON or start your
vehicle.
*
[IP27650(ALL)01/95]
3. Find the autolamp thumbwheel to the left of
the steering wheel on the instrument panel.
[IP27750(ALL)02/95]
4. Turn the autolamp thumbwheel past the stop
to the beginning of the MAX position. The
indicator light will come on.
*
[IP27850(ALL)01/95]
5. The autolamp automatically turns the lamps
on and off for you.
[IP27950(ALL)08/95]
Do not put any articles on top of the photocell
that is located in the top right corner of the
instrument panel. This photocell controls the
autolamp. If you cover it, the photocell reacts as
if it is nighttime, and the lamps turn on.
*
[IP28050(ALL)01/95]
To turn the autolamp off, move the thumbwheel
back to OFF.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995