1996 Mercury Sable belt

38
*
[SR23001(ALL)03/95]
2. Pull down on shoulder belt, then grasp
shoulder belt and lap belt together. Figure 1.
*
[SR23050(ALL)04/95]
half page art:0011238-B
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

39
*
[SR23100(ALL)03/95]
3. While holding the shoulder and lap belt
portions together, route the tongue through
the child seat according to the child seat
manufacturer's instructions. See Figure 2. Be
sure that the belt webbing is not twisted.
*
[SR23150(ALL)04/95]
half page art:0011239-B
Routing the lap/shoulder belt
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

40
*
[SR23200(ALL)04/95]
half page art:0011240-B
Buckling the belt
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

41 [SR23250(ALL)11/94]
4. Grasp the shoulder portion of the belt and
pull downward until all of the belt is
extracted and a click is heard. At this time,
the retractor is in the automatic locking
mode (child seat restraint mode). Figure 4.
*
[SR23301(ALL)04/95]
half page art:0011241-A
Setting the retractor to automatic locking mode
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

42 [SR23350(ALL)11/94]5. Allow the belt to retract. Pull up on the
shoulder webbing. A clicking sound will be
heard as the belt retracts. This indicates the
retractor is in the automatic locking mode.
Push down on the child seat while you pull
up on the belt to remove any slack in the
belt. Figures 5 and 6.
*
[SR23401(ALL)04/95]
half page art:0011242-A
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

45
*
[SR23601(ALL)11/94]
7. Double check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor. If you cannot, the
belt is in the automatic locking mode,
Figure 8.
*
[SR23650(ALL)04/95]
half page art:0011245-B
Checking the retractor
[SR23701(ALL)11/94]
8. Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 4
through 7.
*
[SR23750(ALL)03/95]
NOTE: To remove the retractor from automatic
lock mode, allow seat belt to retract
fully to its stowed position and the
retractor will automatically switch back
to the vehicle sensitive locking mode
for normal adult usage.
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

46
*
[SR24750(ALL)01/95]
RWARNING
When using any infant or child
restraint system, it is important that
you follow the instructions and
warnings provided by the
manufacturer concerning its
installation and use. Failure to follow
each of the restraint manufacturer's
instructions could increase the risk or
severity of an injury in the event of
a collision or sudden stop.
%*
[SR24800(ALL)04/95]
Attaching Safety Seats With Tether Straps
*
[SR24950(ALL)04/95]
Some manufacturers make safety seats that
include a tether strap that goes over the back of
the vehicle seat and attaches to an anchoring
point. Other manufacturers offer the tether strap
as an accessory. Contact the manufacturer of
your child safety seat for information about
ordering a tether strap.
*
[SR25050(ALL)04/95]
Front Seats
*
[SR25150(ALL)04/95]
To install a tether from a child safety seat in the
front seat:
*
[SR25250(ALL)04/95]
1. Buckle the lap/shoulder belt (in the seat
directly behind the front passenger seat in
which the child safety seat will be installed).
*
[SR25350(ALL)04/95]
2. Pull all the stored belt out of the rear seat
retractor to switch the retractor to automatic
locking mode.
*
[SR25375(ALL)04/95]
3. Let the retractor wind up the slack from the
lap/shoulder belt.
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

47
*
[SR25425(ALL)04/95]
4. Install the child safety seat in the front seat.
Refer to the previous section onInstalling
Safety Seats. Hook the tether strap hook
around the webbing near the center of the
shoulder portion of the locked lap/shoulder
belt.
*
[SR25525(ALL)04/95]
5. Tighten the tether strap.
*
[SR25550(ALL)04/95]
Rear Seats
*
[SR25600(ALL)04/95]
If you use a tethered safety seat on one of the
rear seats, you can anchor the strap to the
appropriate tether anchor directly behind that
seat position.
[SR25725(ALL)04/95]
Tether anchorage hardware
[SR25800(ALL)04/95]
Attachment holes (at each rear outboard seating
position) have been provided in your vehicle to
attach anchor hardware, if required. Kits can be
obtained at no charge from any Ford or
Lincoln-Mercury dealer.
[SR26100(ALL)04/95]
Be sure to follow the child safety seat
manufacturer's instructions.
*
[SR26500(ALL)04/95]
RWARNING
Tighten the anchor according to
specifications. Otherwise, the safety
seat may not be properly secured and
the child may be injured in a sudden
stop or collision.
[SR26600(ALL)04/95]
In a station wagon, you simply attach the tether
strap to one of the anchors that are already
installed for you.
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995