1996 Mercury Sable display

98 [IP05525(ALL)02/95]
one third page art:0001286-DThe display window
[IP05625(ALL)02/95]
The display window will indicate the selected
temperature and the operating function you
have chosen: AUTO or one of the six manual
overrides. It will also indicate manual control of
the fan speed with the word FAN,
H, and dots.
The display window with all possible displays
and their positions are shown here. Normally
not all are shown at the same time but are
included here to familiarize you with the names
and symbols.
*
[IP05725(ALL)01/95]
Automatic operation
[IP05825(ALL)03/95]
Press the AUTO button and select the desired
temperature. The selected temperature and
AUTO will be shown in the Display window.
The EATC will automatically heat or cool to
achieve the set temperature. Under normal
conditions, your EATC will need no additional
attention.
[IP05925(ALL)02/95]
one inch art:0001287-B
The AUTO temperature display
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

100 [IP06625(ALL)11/94]Fan speed button
[IP06725(ALL)04/95]
Your EATC automatically adjusts the fan speed
to the existing conditions. You must press AUTO
for automatic fan speed operation. To control the
fan speed yourself, use the button which will
cancel the automatic fan speed control. The
button is located at the left side of the EATC
control panel. It is marked
H. Press the (-) side
for lower speeds. Press the (+) side for higher
speeds.
[IP06925(ALL)03/95]
When you press the fan speed button, the fan
speed will go to manual control. The display
window will show the word FAN,
Hand a
series of dots along with the selected
temperature and operating function.
[IP07025(ALL)02/95]
one inch art:0001290-B
The fan display
[IP07125(ALL)03/95]
You can override the fan speed at any time. If
you use the button to control the fan speed, the
EATC will continue to control the temperature
but you control the fan speed. To return to auto
fan control, press the AUTO button. If you are
operating in one of the override functions (S,
MAX A/C, etc.), automatic fan control will
continue unless you press the fan speed button.
To return to automatic fan control, press the
AUTO button. The EATC will return to
automatic operation. If you want to return to
any override function, press the button for that
function. The fan speed will continue to be
automatically controlled.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

101
*
[IP07225(ALL)01/95]
Manual override buttons
[IP07325(ALL)04/95]
Your EATC has six buttons which allow you to
make special selections. The buttons are located
along the bottom edge of the EATC and allow
you to determine where the air will be
discharged. Pressing any override button
changes the air discharge location only. It does
not affect the ability of the system to control
temperature or the fan speed. Return to fully
automatic operation by pushing the AUTO
button.
*
[IP07425(ALL)01/95]
MAX A/C button
[IP07525(ALL)04/95]
The MAX A/C feature allows for faster cooling
because air is drawn from inside the vehicle.
Using inside air causes the fan to sound louder
which is normal for this selection. The display
window will change to indicate MAX A/C and
the airflow will be from the instrument panel
registers. To exit, push AUTO or any of the
other five manual override buttons.
%*
[IP07625(ALL)01/95]
VENT button
[IP07725(ALL)03/95]
Press this button to select outside air through
the instrument panel registers. The display
window will show the set temperature and
VENT to the lower right of the temperature.
Your EATC will heat the air if the temperature
you have selected is warmer than the outside air
coming into the vehicle. However, the air will
NOT be cooled regardless of the temperature
setting. Airflow will be from the instrument
panel registers.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

102 [IP07825(ALL)04/95]S(Panel and floor) button
[IP07925(ALL)02/95]
Push this button to get air from the floor and
instrument panel registers at the same time. The
display will show the set temperature andS.
Depending on the selected temperature, the air
will be automatically heated or cooled.
[IP08025(ALL)04/95]
R(Floor)
[IP08125(ALL)03/95]
Airflow will be to the floor when theR(floor)
button is pressed. The display window will
show the set temperature andR(floor) to the
right of the temperature. Fan speed will be
automatic unless manually controlled. If you
override the fan speed and wish to return to
automatic fan control, press AUTO. Then, again
selectR(floor) for airflow to the floor.
[IP08225(ALL)04/95]
P(Floor and defrost)
[IP08325(ALL)02/95]
Press this button to get air to the floor and
windshield defrosters at the same time. The
display will show the set temperature andP.If
the outside temperature is about50ÊF (10ÊC) and
above, the air will be dehumidified to remove
moisture. This will help to prevent fogging in
humid weather.
[IP08425(ALL)04/95]
VF-DEF (Front defrost)
[IP08525(ALL)02/95]
Press theVF-DEF (front defrost) button to
obtain maximum airflow to the windshield.
Adjust the temperature setting as required for
defrosting. The Display window will show the
temperature setting withVto the right of the
temperature. When the outside temperature is
about50ÊF (10ÊC) andabove, the air will be
dehumidified to remove moisture. This will help
prevent fogging in humid weather.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

103 [IP08625(ALL)04/95]
OUTSIDE TEMP button
[IP08725(ALL)03/95]
When this button is pressed, the temperature of
the air outside of the vehicle will show in the
display window. If the EATC is off, the display
will go blank after 4 seconds. If the EATC is on,
the outside temperature will be shown until the
OUTSIDE Temp button is pressed a second time
or another override button is pressed.
*
[IP08825(ALL)01/95]
NOTE: The outside temperature reading is
most accurate when the vehicle is
moving. Higher readings may be
obtained when the vehicle is not
moving. The readings that you get may
not agree with temperatures given on
the radio due to differences in vehicle
and station locations.
*
[IP08850(ALL)04/95]
Service
*
[IP08875(ALL)04/95]
If your EATC is not operating as described here,
take it to your dealer to have it checked. System
diagnostics are built in which will allow your
dealer to readily identify problems that might
occur.
[IP08925(ALL)04/95]
Operating tips
[IP09025(ALL)04/95]
The following tips will help you to get the most
satisfaction from your climate control system.
[IP09125(ALL)04/95]
q
In humid weather, selectVF-DEF (front
defrost) before driving. This will help to
prevent windshield fogging. After a few
minutes of operation, switch to any desired
selection.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

172
[AS10600(ALL)04/95]
Stereo and Stereo Cassette Radios
*
[AS10650(ALL)02/95]
Using the Controls on Your New Radio
*
[AS10700(ALL)02/95]
How to turn the radio on and off
[AS10750(ALL)04/95]
Press the ªVOL PUSH ONº button to turn the
radio on. Press again to turn off.
*
[AS10800(ALL)01/95]
How to adjust the volume
[AS10825(ALL)02/95]
Turn the ªVOL PUSH ONº knob to the right to
increase the volume and to the left to decrease
the volume. Dots illuminate in the display to
show relative volume level.
[AS10840(ALL)04/95]
NOTE: If the volume is set above a certain
level when the ignition is turned off,
the volume will come back to a
ªnominalº listening level when the
ignition is turned back on. However, if
the radio power is turned off with the
ªVOL PUSH ONº button, the volume
will not change and will remain at the
level set when the radio is turned back
on.
*
[AS11000(ALL)02/95]
Selecting the AM or FM frequency band
[AS11125(ALL)04/95]
Press the ªAMº or ªFMº button to select the
desired frequency band or to stop/store cassette
tape (when a cassette is playing). Pressing the
ªFMº button more than once will alternate
between FM1 and FM2. These functions are used
with the station memory buttons described
underHow to tune radio stations.
%*
[AS11200(ALL)01/95]
How to tune radio stations
[AS11300(ALL)04/95]
There are four ways for you to tune in a
particular station. You can manually locate the
station using the ªTUNEº button, ªSEEKº to the
station, ªSCANº to the station or select the
station by using the memory buttons. These four
methods are described below.
File:fcass.ex
Update:Wed Dec 20 09:30:38 1995

174 [AS12900(ALL)02/95]Follow the steps below to set these buttons to
the desired frequencies:
*
[AS13025(ALL)03/95]
1. Select a band, then select a frequency.
*
[AS13200(ALL)02/95]
2. Press one of the memory buttons and hold
the button until the sound returns. That
station is now held in memory on that
button.
*
[AS13300(ALL)02/95]
3. Follow the two steps above for each station
memory preset button you want to set.
[AS13510(ALL)04/95]
q
Using the Radio Set feature
[AS13515(ALL)04/95]
With Radio set, you can automatically set
strong stations into your memory buttons.
AM, FM1 and FM2 will be set sequentially.
[AS13545(ALL)04/95]
Turn the radio off with the ªVOL PUSH ONº
knob. Press and hold the ªSCANº button and
turn the radio on by pressing the ªVOL
PUSH ONº knob. Continue holding the
ªSCANº button until ªRADº is shown in the
display.
[AS13550(ALL)04/95]
NOTE: If there are less than six strong stations
in the frequency band, the remaining
unfilled buttons will store the last
strong station detected on the band.
*
[AS13560(ALL)04/95]
After all stations have been filled, the radio will
begin playing the station stored on memory
button 1.
*
[AS13600(ALL)02/95]
Adjusting the tone balance and speaker
output of your radio
*
[AS13800(ALL)02/95]
q
Increasing or decreasing bass response
[AS13925(ALL)02/95]
Press the right (
a) side of the ªBASSº button
to increase bass (more ªlowsº); press the left
(
b) side of the ªBASSº button to decrease
bass (less ªlowsº).
File:fcass.ex
Update:Wed Dec 20 09:30:38 1995

175
*
[AS14000(ALL)02/95]
q
Increasing or decreasing treble response
[AS14125(ALL)02/95]
Press the right (
a) side of the ªTREBº
button to increase treble (more ªhighsº);
press the left (
b) side of the ªTREBº button
to decrease treble (less ªhighsº).
*
[AS14400(ALL)02/95]
q
Adjusting speaker balance
[AS14525(ALL)04/95]
Balance control allows you to adjust the
sound distribution between the right and left
speakers. Press the right (
a) side of the
ªBALº button to shift the sound to the right
speakers, and press the left (
b) side to shift
the sound to the left speakers. The display
will show ªBALº and a dot indicating the
balance position.
*
[AS14600(ALL)02/95]
q
Adjusting speaker fader
[AS14725(ALL)04/95]
Fade control allows you to adjust the sound
distribution between the front and rear
speakers. Press the right (
a) side of the
ªFADEº button to shift the sound to the front
speakers, and press the left (
b) side to shift
the sound to the rear speakers. The display
will show ªFADEº and a dot indicating the
fade position.
[AS14800(ALL)04/95]
Using the Power Antenna (If equipped)
*
[AS14850(ALL)02/95]
The power antenna will automatically rise when
your radio is turned on and the ignition is in the
ON or ACC position. It will lower when either
the radio or the ignition is turned off.
*
[AS14900(ALL)02/95]
Power antenna maintenance and care
*
[AS14950(ALL)02/95]
q
Never drive your vehicle through a car wash
with the power antenna mast extended. This
can cause damage to the antenna mast, which
is not covered under warranty. Turn off your
radio and/or the vehicle. This will
automatically retract the antenna.
File:fcass.ex
Update:Wed Dec 20 09:30:38 1995