1996 Mercury Sable buttons

121
malfunction. Therefore, use only properly
installed FCC approved radio transmitting
equipment in your vehicle.
[SC08000(ALL)11/94]
one third page art:0001399-B
The speed control buttons on the steering wheel
*
[SC08200(ALL)03/95]
To set the speed control:
[SC08400(ALL)11/94]
1. Press and release the ON switch. The
CRUISE indicator light in the instrument
cluster will illuminate to indicate that speed
control is in a standby mode.
*
[SC08500(ALL)04/95]
2. Accelerate to the desired speed above
30 mph (50 km/h) using the accelerator
pedal.
*
[SC08800(ALL)03/95]
3. Press the SET ACCEL switch and release it
immediately to set your speed. If you keep
this switch pressed, your speed will continue
to increase.
*
[SC08900(ALL)03/95]
4. Take your foot off the accelerator pedal.
Your vehicle will maintain the speed you set.
*
[SC09000(ALL)01/95]
If you drive up or down a steep hill, your
vehicle may momentarily slow down or speed
up, even though the speed control is on. This is
normal.
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995

128 %
*
[FV04251(ALL)03/95]
Using the Keyless Entry System
(If equipped)
*
[FV04301(ALL)02/95]
If your vehicle has the keyless entry system, you
can lock or unlock the vehicle doors without
using a key. The buttons for the system are near
the outside door handle on the driver's side. See
alsoRemote Entry Systemwhich follows this
description.
[FV04351(ALL)02/95]
one third page art:0000482-C
Keyless entry buttons
*
[FV04401(ALL)02/95]
When you bought your vehicle, you were given
a computer code that operates the system for
your vehicle. For your convenience, we have
duplicated this code in two places.
*
[FV04451(ALL)02/95]
The code is:
*
[FV04501(ALL)02/95]
q
on your owner's wallet card found in the
glove compartment
*
[FV04551(ALL)02/95]
q
taped to the computer module
[FV04601(ALL)03/95]
When you use this entry system, the illuminated
entry system turns on the interior lights for 25
seconds and the buttons on the keypad light up
for 5 seconds. Do not push the buttons with a
key, ballpoint pen, pencil or any other hard
object. These objects could damage the buttons.
File:fcfvs.ex
Update:Wed Dec 20 09:39:11 1995

129 %
*
[FV04651(ALL)02/95]
Programming your own entry code
*
[FV04700(ALL)02/95]
You can program a personal code to unlock
your vehicle with the keypad. This code does
not replace the permanent code that the
dealership gave you. Use your personal code in
the same manner as you would your original
code.
*
[FV04751(ALL)02/95]
To program your own code:
*
[FV04801(ALL)02/95]
1. Select five digits for your personal code.
*
[FV04851(ALL)02/95]
2. Enter the permanent code that the dealership
gave you.
*
[FV04901(ALL)02/95]
3. Within five seconds, press 1/2.
*
[FV04951(ALL)02/95]
4. Within five seconds of pressing 1/2, enter
your personal code, pressing each digit
within five seconds of the previous digit.
*
[FV05000(ALL)02/95]
The keyless entry system registers this
second code. To open your vehicle, you can
now use either code. The module remembers
only one personal code at a time. Entering a
second personal code will erase the first,
replacing it with the new second one.
*
[FV05050(ALL)02/95]
To erase your personal code:
*
[FV05101(ALL)02/95]
1. Enter the original permanent code.
*
[FV05150(ALL)02/95]
2. Press 1/2 within five seconds of Step 1.
*
[FV05201(ALL)02/95]
3. Wait six seconds.
*
[FV05250(ALL)02/95]
The keyless entry system automatically
erases your personal code. The system will
now only respond to the permanent code.
*
[FV05301(ALL)02/95]
Do not set a code that presents the numbers in
sequential order, such as 1/2, 3/4, 5/6, 7/8, 9/0.
Studies show that people who idly press the
buttons usually press a sequential pattern. Also,
do not select a code that uses the same button
five times. Thieves can easily figure out these
types of codes.
File:fcfvs.ex
Update:Wed Dec 20 09:39:11 1995

132
*
[FV06400(ALL)02/95]
The doors may not lock automatically at the
correct time if the driver:
*
[FV06450(ALL)02/95]
q
shifts through gears without pressing the
brake
*
[FV06500(ALL)02/95]
q
shifts through gears quickly after starting the
vehicle
*
[FV06550(ALL)02/95]
q
releases their foot from the brake while
someone has stepped out of the vehicle for a
moment
*
[FV06575(ALL)04/95]
You can deactivate the system by using the
buttons for the keyless entry system if you don't
want to use the Autolock feature.
*
[FV06600(ALL)02/95]
To deactivate the Autolock system:
*
[FV06650(ALL)02/95]
1. Enter your permanent five-digit entry code
(not the user code you may have set).
*
[FV06700(ALL)02/95]
2. Within 5 seconds, press and hold 7/8.
*
[FV06750(ALL)02/95]
3. Within 5 more seconds, press and release
3/4.
*
[FV06800(ALL)02/95]
4. Release 7/8.
*
[FV06850(ALL)02/95]
To reactivate the Autolock system, simply repeat
the instructions for deactivating the system. By
re-entering the code that deactivates the
Autolock, the keyless entry system reinstates the
Autolock feature.
*
[FV06900(ALL)04/95]
You can also deactivate or reactivate the
Autolock feature by this method:
[FV06950(ALL)04/95]
1. Make sure the anti-theft system is not armed
or triggered, ignition is off, and all doors
and liftgate are closed.
*
[FV07000(ALL)02/95]
2. Turn the ignition key from OFF to RUN.
*
[FV07050(ALL)02/95]
3. Press the door power unlock button 3 times.
*
[FV07100(ALL)02/95]
4. Turn the ignition key from RUN to OFF.
File:fcfvs.ex
Update:Wed Dec 20 09:39:11 1995

133
*
[FV07150(ALL)02/95]
5. Press the door power unlock button 3 times.
*
[FV07200(ALL)02/95]
6. Turn the ignition key back to RUN within 30
seconds of step 2.
*
[FV07250(ALL)02/95]
7. The horn should chirp once. If not, wait 30
seconds and repeat steps 1 through 6.
*
[FV07300(ALL)02/95]
8. Press the door power unlock button.
*
[FV07350(ALL)02/95]
9. Press the door power lock button.
*
[FV07400(ALL)02/95]
10. The horn will chirp once if the Autolock
feature was deactivated, twice (one short
chirp followed by a long chirp) if the
Autolock feature was activated.
*
[FV07450(ALL)02/95]
11. Turn the ignition OFF.
[FV07550(ALL)03/95]
Remote Entry System (If equipped)
*
[FV07600(ALL)02/95]
If your vehicle has the remote entry system, you
can lock or unlock the vehicle doors and liftgate
without using a key. The remote also has a
personal alarm feature. The buttons for the
system are located on the two hand held
transmitters that came with your vehicle.
*
[FV07650(ALL)02/95]
The system will work with up to four
transmitters. Your vehicle came with two
transmitters. Additional transmitters can be
ordered from your dealer.
*
[FV07700(ALL)02/95]
The remote entry features only operate with the
ignition in the OFF position.
File:fcfvs.ex
Update:Wed Dec 20 09:39:11 1995

135
lock again, the horn will chirp and the external
lamps will flash. If a door or the liftgate is open
or ajar, the horn will give two short chirps
warning you that a door or the liftgate is open.
%*
[FV08100(ALL)02/95]
Remote entry personal alarm
*
[FV08151(ALL)02/95]
If you wish to activate the remote entry system
personal alarm, press the PANIC button. This
will honk the horn and flash the lights for
approximately 2 minutes 45 seconds. You can
turn it off by pressing the PANIC button again
from the transmitter or by turning the ignition
to the ON or ACCESSORY position.
*
[FV08200(ALL)02/95]
When you use the remote entry UNLOCK or
PANIC buttons, the illuminated entry system
turns on the vehicle's interior lights for 25
seconds. You can turn these lights off with the
remote entry LOCK button or by turning the
ignition to the ON or ACCESSORY position.
[FV08251(ALL)04/95]
THIS DEVICE COMPLIES WITH PART 15 OF
THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS
DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
%*
[FV08300(ALL)04/95]
Arming and Disarming the Alarm System
with Remote Entry
*
[FV08351(ALL)04/95]
Your Remote Entry System will automatically
arm the factory installed Anti-Theft System when
the doors are locked, and automatically disarm it
when the doors are unlocked. The remote will
also reset the anti-theft alarm (when the driver's
door is unlocked or the PANIC button is pressed
on a programmed remote entry transmitter) if it
was triggered.
File:fcfvs.ex
Update:Wed Dec 20 09:39:11 1995

138 [FV09801(ALL)04/95]Arming the system
*
[FV09851(ALL)04/95]
The system is ready to arm any time the ignition
switch is turned OFF and the alarm is not
triggered or sounding. Any of the following
events will prearm the anti-theft system:
[FV09900(ALL)04/95]
q
Pressing the remote entry transmitter LOCK
button to lock the doors (with the doors open
or closed).
[FV09951(ALL)04/95]
q
Pressing the 7/8 and 9/10 buttons on the
Keyless Entry Keypad at the same time to
lock the doors (with the doors open or
closed).
*
[FV10001(ALL)04/95]
q
Opening a door and pressing the power door
lock button to lock the doors.
[FV10050(ALL)04/95]
q
Turning the driver's or front passenger's door
key to the LOCK position to centrally lock all
doors (with the doors open or closed).
*
[FV10100(ALL)04/95]
If a door or the liftgate is open, the anti-theft
system is prearmed and waiting for all doors to
close. The THEFT indicator in the instrument
panel will light continuously while the system is
prearmed.
*
[FV10201(ALL)04/95]
Once all doors and the liftgate are closed, if any
were open, the system will begin a 30 second
countdown to become armed. The 30 second
countdown allows people who may still be in
the vehicle time to exit without triggering the
alarm. The THEFT indicator will glow steadily
until the system is armed. When the system is
armed, the THEFT indicator will begin to flash
with short flashes every 2 seconds until the
system is triggered or disarmed.
*
[FV10251(ALL)02/95]
Remember, all doors and the liftgate must be
fully closed for the anti-theft system to arm. If a
door or the liftgate has been left open or ajar,
and you press the remote entry transmitter twice
File:fcfvs.ex
Update:Wed Dec 20 09:39:11 1995

172
[AS10600(ALL)04/95]
Stereo and Stereo Cassette Radios
*
[AS10650(ALL)02/95]
Using the Controls on Your New Radio
*
[AS10700(ALL)02/95]
How to turn the radio on and off
[AS10750(ALL)04/95]
Press the ªVOL PUSH ONº button to turn the
radio on. Press again to turn off.
*
[AS10800(ALL)01/95]
How to adjust the volume
[AS10825(ALL)02/95]
Turn the ªVOL PUSH ONº knob to the right to
increase the volume and to the left to decrease
the volume. Dots illuminate in the display to
show relative volume level.
[AS10840(ALL)04/95]
NOTE: If the volume is set above a certain
level when the ignition is turned off,
the volume will come back to a
ªnominalº listening level when the
ignition is turned back on. However, if
the radio power is turned off with the
ªVOL PUSH ONº button, the volume
will not change and will remain at the
level set when the radio is turned back
on.
*
[AS11000(ALL)02/95]
Selecting the AM or FM frequency band
[AS11125(ALL)04/95]
Press the ªAMº or ªFMº button to select the
desired frequency band or to stop/store cassette
tape (when a cassette is playing). Pressing the
ªFMº button more than once will alternate
between FM1 and FM2. These functions are used
with the station memory buttons described
underHow to tune radio stations.
%*
[AS11200(ALL)01/95]
How to tune radio stations
[AS11300(ALL)04/95]
There are four ways for you to tune in a
particular station. You can manually locate the
station using the ªTUNEº button, ªSEEKº to the
station, ªSCANº to the station or select the
station by using the memory buttons. These four
methods are described below.
File:fcass.ex
Update:Wed Dec 20 09:30:38 1995