1996 Mercury Mystique jump cable

160
*
[RE00850(ALL)06/95]
If the acid touches someone's skin, eyes, or clothing,
immediately flush the area with water for at least 15 minutes. If
someone swallows the acid, have him or her drink lots of milk
or water first, then Milk of Magnesia, a beaten egg, or vegetable
oil. Call a doctor immediately.
*
[RE00900(ALL)03/95]
To avoid damaging your vehicle or your battery, and to avoid
injury to yourself, follow these directions for preparing your
vehicle to jump-start and connecting the jumper cables in the
order they are given. If in doubt, call for road service.
*
[RE01000(ALL)03/95]
Preparing Your Vehicle
*
[RE01100(ALL)03/95]1.
Your vehicle has a 12-volt starting system, so you need to
use a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you
connect them to a 24-volt power supply (either two 12-volt
batteries in series or a 24-volt generator set).
*
[RE01200(ALL)03/95]2.
Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
*
[RE01300(ALL)04/95]3.
Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set
the parking brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[RE01400(ALL)03/95]4.
Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[RE01600(ALL)03/95]5.
Turn on the heater fan in both vehicles. Press the DEFROST
button. Turn off all other switches and gauges.
File:cdrez.ex
Update:Fri Feb 23 11:03:34 1996

Roadside Emergencies
161
%*
[RE01700(ALL)05/95]
Connecting the jumper cables
*
[RE02500(ALL)03/95]1.
Connect one end of the first jumper cable to the positive (+)
terminal of the discharged battery. (You can connect either
jumper cable to the positive (+) terminal, as long as you use
the same cable for both positive terminals.) Most jumper
cables have a red cable and a black cable. The red cable is
generally used for the positive terminals and the black for
the negative ones.
*
[RE02600(ALL)04/95]2.
Connect the other end of the first cable to the positive (+)
terminal of the booster battery.
*
[RE02700(ALL)05/95]3.
Connect one end of the second cable to the negative (s)
terminal of the booster battery Ð NOT to the discharged
battery.
*
[RE02800(ALL)04/95]4.
Connect the other end of the second cable to a good metallic
surface on the engine or frame of the disabled vehicle.
*
[RE02900(ALL)05/95]
RWARNING
Do not connect the end of the second cable to the
negative (s) terminal of the battery to be jumped. A
spark may cause an explosion of the gases that surround
the battery.
File:cdrez.ex
Update:Fri Feb 23 11:03:34 1996

162
[RE02975(ALL)01/95]
27-1/2 pica art:0001006-E
Sequence for connecting jumper cables
File:cdrez.ex
Update:Fri Feb 23 11:03:34 1996

Roadside Emergencies
163
*
[RE03400(ALL)03/95]
Jump-Starting
*
[RE03600(ALL)03/95]1.
Make sure that the jumper cables are not in the way of
moving engine parts, then start the booster vehicle. Run the
engine at a moderate speed.
*
[RE03700(ALL)03/95]2.
Let the discharged battery charge for a few minutes and then
start the disabled vehicle. It may take a couple of tries before
the vehicle starts. If the vehicle does not start after several
attempts, there may be a different problem.
*
[RE03800(ALL)03/95]3.
When both vehicles are running, let them idle for a few
minutes to charge the discharged battery.
*
[RE03900(ALL)03/95]
Removing jumper cables
*
[RE04000(ALL)03/95]1.
Always remove the jumper cables in the reverse order.
Remove the negative (±) end of the jumper cable from the
metallic surface on the engine or frame of the disabled
vehicle.
*
[RE04100(ALL)05/95]2.
Remove the negative (±) cable from the booster battery.
*
[RE04200(ALL)03/95]3.
Remove the positive (+) cable from the booster battery.
*
[RE04300(ALL)05/95]4.
Remove the other end of the positive (+) cable from the
discharged battery.
*
[RE04400(ALL)04/95]
After the vehicle is started, let it idle for a while to let the
engine ªrelearnº its idle conditions. Drive it around for a while
with all electrical accessories turned off to let the battery
recharge.You may need to use a battery charger to fully
recharge the battery.
*
[RE04450(ALL)03/95]
If you need to replace your battery, seeBatteryin theServicing
Your Vehiclechapter.
File:cdrez.ex
Update:Fri Feb 23 11:03:34 1996

282 Hood
latch location.................... 198
lubrication specifications............... 254
release lever.................... 198
working under the hood............... 196
Horn.......................... 84
I
Identification Number, Vehicle (VIN)........177, 182
Idle
relearning..................... 163
speed........................ 48
Ignition
chime........................ 43
positions of the ignition................ 41
removing the key................... 42
Indicator lights and chimes (see Lights).......... 67
Infant seats (see Safety seats)............... 24
Instrument cluster.................... 53
Instrument panel
lighting up panel and interior............. 77
location of components................ 67
Interval wipers..................... 82
J
Jack
operation...................... 167
positioning..................... 167
Jump-starting your vehicle
attaching cables................... 161
disconnecting cables................. 163
K
Keys
key in ignition chime................. 43
positions of the ignition................ 41
removing from the ignition.............. 42
stuck in lock position................. 41
File:cdixz.ex
Update:Fri Feb 23 10:58:07 1996