1996 Lexus LS400 parking brake

125
SECTION 3 ± 1
STARTING AND DRIVING
Starting and driving
Three±way catalytic converter 126
Engine exhaust caution 127
Before starting the engine 128
Ignition switch with steering lock 128
Parking brake 129
How to start the engine 130
Automatic transmission 131
Cruise control 136
Electronically modulated air suspension 139
Traction control system 141
Brake system 142
Types of tires 145

STARTING AND DRIVING
129 If you leave the key in the ªACCº or ªLOCKº position and
open the driver's door, a buzzer will remind you to remove
the key.
ªLOCKº ± Engine is off and the steering wheel is locked.
The ignition key can be removed only at this position.
To turn the key from ªACCº to the ªLOCKº position, you must
put the transmission selector lever in the ªPº position.
When starting the engine, the key may seem stuck at the
ªLOCKº position. To free it, first be sure the key is pushed all
the way in, and then rock the steering wheel slightly while
turning the key gently.
If, in an emergency, you must turn the engine off while the
vehicle is moving, turn the key only to ªACCº.
PARKING BRAKE

To set: Fully depress the parking brake pedal.
To release: Pull the parking brake release lever.
Before leaving your vehicle, firmly apply the parking brake.
CAUTION!
Before driving, make sure the parking brake is fully
released and that the parking brake reminder light is
off.

STARTING AND DRIVING
130
HOW TO START THE ENGINE
Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3. Put the selector lever in ªPº. If you need to restart the
engine while the vehicle is moving, put the selector lever in
ªNº. A starter safety device will prevent the starter from
operating if the selector lever is in any drive position.
4. Depress the brake pedal and hold it to the floor until you
are ready to drive off.
Starting the engine
Before starting the engine, be sure to follow the instructions
in ªBefore crankingº.
Normal starting procedure
The multiport fuel injection system/sequential multiport fuel
injection system in your engine automatically controls the
proper air±fuel mixture for starting. You can start a cold or hot
engine as follows:
1. With your foot off the accelerator pedal, crank the engine
by turning the key to ªSTARTº. Release it when the engine
starts.
2. After the engine runs for about 10 seconds, you are
ready to drive.If the weather is below freezing, let the engine warm up for
a few minutes before driving. Do not leave the vehicle while
the engine is warming up.
If the engine stalls...
Simply restart it, using the correct procedure given in normal
starting.
If the engine will not start
See ªIf your vehicle will not startº on page 160.
NOTICE
Do not crank for more than 15 seconds at a time.
This may overheat the starter and wiring systems.
Do not race a cold engine.
If the engine becomes difficult to start or stalls
frequently, have the engine checked immediately.

STARTING AND DRIVING
131
AUTOMATIC TRANSMISSION
Your automatic transmission has a shift lock system to
minimize the possibility of incorrect operation. This
means you can only shift out of ªPº position when the
brake pedal is depressed with the ignition switch in
ªONº position. ()
The shift position is displayed on the instrument
cluster.
P:Parking, engine starting and key removal position
R:Reverse position
N:Neutral position
D:Normal driving position (Shifting into overdrive possible)
3:Position for engine braking (Shifting into overdrive not
possible)
When the cruise control is being used, even if you
downshift from ªDº to ª3º, engine braking will not be
applied because the cruise control is not cancelled. For
the operation to decrease the vehicle speed, see page
138.
2:Position for more powerful engine braking
L:Position for maximum engine braking
Correct use of the automatic transmission is explained
in the following parts.
(a) Normal driving
(b) Using engine braking
(c) Using the ª2º and ªLº positions
(d) Backing up
(e) Parking
(f) Good driving practice
(g) If you cannot shift the selector lever

STARTING AND DRIVING
133

ªDº (Drive) positionBrake pedal
4. With your foot holding down the brake pedal, shift
the selector lever to ªDº.
Always use the ªDº position to improve fuel economy and
quiet driving. Only in this position, shifting into the overdrive
gear is possible. However, while the engine coolant
temperature is low, the transmission will not shift into the
overdrive gear even in the ªDº position. (See ª(b) Using
engine brakingº and ª(f) Good driving practiceº for
exceptions.)
CAUTION!
Never put your foot on the accelerator pedal while
shifting.5. Release the parking brake and brake pedal. Depress
the accelerator pedal slowly for smooth starting.
In normal cruising, the vehicle will start in the first gear and
automatically shift to the most suitable gear for the running
conditions.
In ª3º position, the automatic transmission system will select
the most suitable gear for the running conditions such as hill
climbing, hard towing, etc.
If you need to accelerate rapidly while driving, depress the
accelerator pedal to the full throttle position. This provides
more acceleration by automatically downshifting the
transmission to the next lower gear or beyond, depending on
the vehicle speed.
If engine braking is needed, such as in descending a long hill,
see ª(b) Using engine brakingº.

STARTING AND DRIVING
135
Do not continue hill climbing or hard towing for a
long time in the ª2º or ªLº position. This may cause
severe automatic transmission damage from
overheating. To prevent such damage, ª3º position
should be used in hill climbing or hard towing.
(d) Backing up

ªRº (Reverse) positionBrake pedal
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the
selector lever to the ªRº position.
NOTICE
Never shift into reverse while the vehicle is moving.
(e) Parking

ªPº (Park) positionBrake pedal
Parking brake pedal
1. Bring the vehicle to a complete stop.
2. Depress the parking brake pedal fully.
3. With the brake pedal held down with your foot, shift the
selector lever to the ªPº position.
CAUTION!
While the vehicle is moving, never attempt to move
the selector lever into ªPº under any circumstances.
Serious mechanical damage and loss of vehicle
control may result.

STARTING AND DRIVING
136
(f) Good driving practice

If the transmission repeatedly upshifts and downshifts
between the third and overdrive gears when climbing a
gentle slope, shift the selector lever to the ª3º position. Be
sure to shift the selector lever to the ªDº position after
climbing the slope.
When towing a trailer, in order to maintain efficient engine
braking and electrical charging performance, do not use
overdrive. The selector lever must be in the ª3º position.
CAUTION!
Always keep your foot on the brake pedal while
stopped with the engine running. This prevents the
vehicle from creeping.
NOTICE
Do not hold the vehicle on an upgrade with the
accelerator pedal. This can cause the transmission
to overheat. Always use the brake pedal or parking
brake.
(g) If you cannot shift the selector lever
If you cannot shift the selector lever even though the brake
pedal is depressed, use the shift lock override button. For
instructions, see ªIf you cannot shift automatic transmission
selector leverº on page 175.
CRUISE CONTROL
The cruise control allows you to cruise the vehicle at a
desired speed over 40 km/h (25 mph) with your foot off
the accelerator pedal.
Your cruising speed can be maintained although a slight
speed change may occur when driving up or down a
gradient, within the limits of engine performance. On steeper
hills, a great speed change will occur so it is better to drive
without the cruise control.
When the cruise control is on, the driving pattern of the
automatic transmission is fixed in the normal position,
regardless of the position of the selector switch.
CAUTION!

To help maintain maximum control of your vehicle,
do not use the cruise control when driving in heavy
or varying traffic, or on slippery (rainy, icy or
snow±covered) or winding roads.
Avoid vehicle speed increases when driving
downhill. If the vehicle speed is too fast in relation
to the cruise control set speed, cancel the cruise
control then downshift the transmission to use
engine braking to slow down.

STARTING AND DRIVING
144ªABSº warning light
This light comes on when the ignition key is turned to
the ªONº position. After about 3 seconds, the light will
go off.
If either of the following conditions occurs, this indicates a
malfunction somewhere in the parts monitored by the
warning light system. Contact your Lexus dealer as soon as
possible to service the vehicle.
The light does not come on as described above, or remains
on.
The light comes on while driving.
Even if the anti±lock brake system should fail, the brake
system will still operate conventionally. Have your vehicle
checked by your Lexus dealer as soon as possible.
Drum±in±disc type parking brake system
Your vehicle has a drum±in±disc type parking brake system.
This type of brake system needs bedding±down of the brake
shoes periodically or whenever the parking brake shoes
and/or drums are replaced.
Have your Lexus dealer perform the bedding±down.
Brake pad wear limit warning light
When your brake pads are worn enough to require
replacement, the brake pad wear limit warning light in
the instrument cluster comes on.
If the warning light comes on while driving, have the brake
pads checked and replaced by your Lexus dealer as soon as
possible. Expensive rotor damage can result if the pads are
not replaced when needed.