1996 LAND ROVER DEFENDER engine

FUEL SYSTEM
1
ADJUSTMENT THROTTLE CABLE
Adjust
1.Slacken throttle cable adjustment ferrule.
2.Hold throttle lever in fully closed position.
3.Adjust outer cable, by rotating ferrule, to give
1,57 mm (1/16 in) of deflection in the inner cable.
4.Check that throttle opens fully when the throttle
is depressed.EGR THROTTLE POSITION SENSOR
Check
1.Run engine until normal operating temperature is
reached.
2.Switch off engine and disconnect throttle position
sensor multi-plug.
3.Connect an Ohmmeter across pins 1 and 3 of
multi-plug. Ohmmeter should read between 1K
and 1.05K ohms.
4.Connect Ohmmeter across pins 1 and 2 of
multi-plug. Ohmmeter should read between 850
and 900 ohms.
5.If readings are correct, reconnect multi-plug.
6.If readings are not obtained slacken 2 torx
screws securing sensor.
7.Rotate sensor to obtain correct Ohmmeter
reading, then tighten torx screws.
8.Re-check readings and fit multiplug.
9.If, after adjustment, Ohmmeter readings cannot
be achieved, fit new sensor.
See Repair, EGR
throttle position sensor

19FUEL SYSTEM
2
ADJUSTMENT LOW AND HIGH IDLE SPEED ADJUSTMENT
NOTE: The high idle speed (cold start idle)
is automatically set by the setting of the
low idle speed and cannot be adjusted
individually.
1.Check and adjust throttle cable.
See Throttle
cable
2.Start engine and run it until normal operating
temperature is reached.
3.Using a suitable tachometer, check the engine
idle speed,
See ENGINE TUNING DATA,
Information, 300Tdi
4.If adjustment is necessary, first slacken the
locknut on injection pump.
5.Turn adjustment screw clockwise to increase
engine speed or anti-clockwise to decrease the
speed. Run engine at an increased speed for a
few seconds then check idle speed again.
6.When correct speed has been achieved, hold
adjuster screw steady while tightening locknut.
NOTE: The low idle speed control is the
only permitted adjustment in service. Any
additional adjustments required must be
entrusted to authorised Bosch agents.THROTTLE PEDAL ADJUSTMENT
Adjust
1.First ensure that throttle cable is correctly
adjusted
See Throttle cable
2.Depress throttle pedal, by hand, to full extent of
injection pump lever travel. Slacken locknut and
adjust throttle pedal stop screw to take up
clearance between screw and bulkhead. Ensure
no strain is placed upon throttle cable and pump
lever.
3.Retighten locknut.

FUEL SYSTEM
3
ADJUSTMENT INJECTION PUMP TIMING - CHECK AND ADJUST
Service repair no - 19.30.01
1.Viewing the valve mechanism through oil filler
aperture, turn crankshaft clockwise until inlet
valve of No.1 cylinder has just closed. No.1
cylinder is now just before TDC.
2.Remove blanking plug from flywheel housing
and insert timing toolLRT-12-044, locating
centre pin on flywheel.
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
adjustments or remove and refit procedures are
required, it may be necessary to remove the
undertray and/or integral access panels.
See
CHASSIS AND BODY, Repair, Front undertray
or
See CHASSIS AND BODY, Repair, Rear undertray
3.Cearfully rotate crankshaft clockwise until centre
pin engages timing slot in flywheel.
4.Remove injection pump access plate, complete
with gasket, from front cover plate.
5.Fit locking pinLRT-12-045/2to injection pump
gear. If difficulty is experienced in inserting pin,
adjustments will be needed to correctly set
injection pump timing as follows:
6.Support injection pump retaining nut to prevent
strain on timing belt.
7.Slacken the 3 keeper plate retaining bolts.
8.Carefully turn fixing nut and keeper plate until
locking pin can be inserted, without restriction,
into injection pump gear.
9.Tighten keeper plate bolts to
25 Nm (18 lbf/ft)
and remove locking pin.
10.Refit injection pump access plate plate and
gasket.
11.Remove flywheel timing tool and refit blanking
plug.
12.Run engine until normal operating temperature is
reached and check that idle speed adjustment,
See low and high idle speed adjustmentand
throttle cable adjustment
See Throttle cable
are correct.

19FUEL SYSTEM
4
ADJUSTMENT TURBOCHARGER BOOST PRESSURE - CHECK
Service repair no - 19.42.06
1.Disconnect actuator hose from turbocharger and
insert a suitable 'T' piece connector.
2.Connect a short length of suitable hose to
turbocharger and 'T'piece.
3.Connect further hose to 'T' piece and pressure
gaugeLRT-12-011. The pressure gauge hose
must be long enough to reach into the vehicle
cab so that the gauge can be observed by driver
or passenger.
4.To check maximum boost pressure, drive
vehicle normally, but in such a manner that full
throttle can be maintained whilst climbing a hill
with engine speed held steady between 2,500
and 3,000 rev/min. Under these circumstances
boost pressure should read 0,95 - 1,09 Kgf/cm
2
(13.5 - 15.5 lb/in2).PRIMING THE FUEL SYSTEM
Service repair no - 19.50.01
NOTE: If the fuel system has been
completely drained carry out the
procedures for priming both the
sedimentor, if fitted, and fuel filter and injection
pump.
Sedimentor and fuel filter
If the sedimentor or fuel filter have been dismantled
and air has entered the fuel system carry out the
following procedure:
1.Slacken fuel filter bleed screw.
2.Operate hand priming lever on fuel lift pump until
fuel, free from air, emerges from filter.
NOTE: Ensure that the fuel pump lever is
on the bottom of operating cam when
priming, otherwise maximum movement of
the lever cannot be achieved.
3.Tighten filter bleed screw whilst fuel is still
emerging.

FUEL SYSTEM
5
ADJUSTMENT Fuel injection pump
If the fuel injection pump has been removed or
renewed carry out the following:
1.Slacken fuel inlet pipe banjo bolt at injection
pump.
2.Operate hand priming lever on fuel lift pump until
fuel, free from air, emerges from injection pump.
3.Tighten banjo bolt whilst fuel is still emerging.
4.Crank engine until fuel is drawn through the
system and engine starts.
5.Check fuel connections for leaks.

FUEL SYSTEM
3
REPAIR FUEL INJECTORS
Service repair no - 19.60.10
Remove
NOTE: When a fuel injector is considered
to be the cause of irregular running and
loss of power it will be necessary to fit a
donor set of injectors to determine which injector
is at fault. DO NOT attempt to dismantle or carry
out spray tests on the fuel injectors. This work
can only carried out by authorised Bosch dealers.
1.Remove oil filler cap and release sound
insulation cover from top of engine.
2.Disconnect high pressure fuel supply pipes from
injectors and injection pump. Remove in pairs.
3.Disconnect spill return hose(s) from injectors.
4.Plug pipes and injector connections to prevent
the ingress of dirt and foriegn matter.5.Remove retaining nut and release each injector
clamp plate from cylinder head.
6.Remove injector and discard copper washer.
Refit
7.Ensure injectors and seating in cylinder head are
clean.
8.Lightly grease a new copper sealing washer and
position on each injector.
9.Fit injectors in cylinder head with spill return
outlets facing outward.
10.Secure injector with clamp plate and nut. Tighten
nut to
25 Nm (18 lbf/ft).
NOTE: The clamp plates are slightly
curved and should be fitted with the
convex side uppermost.
11.Fit the spill return pipe with a single copper
washer under the head of the banjo bolt and 2
copper washers fitted between the injector and
the banjo. Tighten banjo bolt to
10 Nm (7 lbf/ft).
12.Fit high pressure pipes to injectors and injection
pump. Tighten union nuts to
28 Nm (21 lbf/ft).
13.Fit sound insulation cover and oil filler cap.

FUEL SYSTEM
7
REPAIR REV: 05/99
13.Remove single bolt fixing assembly securing
front of tank to chassis mounted bracket.
14.Remove 3 bolts securing tank mounting bracket
to chassis and release bracket.
15.Lower front of tank while turning anti-clockwise
and remove from vehicle.
16.If required, remove tank gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
17.Fit filler hose and clip to tank but do not fully
tighten. Position clip screw so that it is
accessible when tank is fitted.
18.Fit breather hose and secure with clip.
19.Position fuel tank in vehicle and loosely secure
front mounting bracket to tank with special bolt
and rubber bushes.
20.Secure mounting bracket to chassis with 3 bolts
and fully tighten to
20 Nm (15 lbf/ft).
21.Secure rear of tank to chassis mounting and
tighten captive bolt plate fixings to
20 Nm (15
lbf/ft).
22.Fully tighten front fixing bolt assembly to20 Nm
(15 lbf/ft).
23.Fit spill return and fuel supply pipes and secure
union connections.
24.Fit fuel level unit electrical plug.
25.Fit hose to filler tube and tighten upper and lower
clips.
26.Check that drain plug is secure and fill fuel tank.
27.Reconnect battery.
28.Prime fuel system
See Adjustment, Priming
the fuel system
and start engine.
29.Check system for leaks and operation of fuel
gauge.
30.Fit seat base cover and seat cushion.SIDE MOUNTED FUEL TANK - 5 DOOR VEHICLES
Service repair no - 19.55.01
NOTE: This fuel tank is used on 110/130 5
door vehicles fitted with a twin tank
option.
WARNING: Before any attempt is made to
start the removal procedure it is vital that
the FUEL HANDLING PRECAUTIONS,
See
INTRODUCTION, Information, Fuel handling
precautions
are carefully studied and
implemented in the interests of safety.
Remove
1.Disconnect battery.
2.Remove tank drain plug, allow fuel to drain into a
clean container, and refit plug.
3.Remove RH seat cushion.
4.Remove retaining catch and remove seat base
cover to gain access to fuel tank.
5.Disconnect electrical plug from fuel gauge unit.
6.Disconnect fuel supply pipe from tank.
7.Disconnect spill return pipe from tank.
8.Remove 3 bolts securing tank to front mounting
bracket.
9.Support front of tank and remove single fixing
assembly securing tank to rear mounting
bracket.
10.Remove tank from vehicle.
11.If required, remove fuel gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
12.Position fuel tank in vehicle and loosely secure
to rear mounting bracket with special bolt and
rubber bushes.
13.Secure tank to front mounting bracket and
tighten fixings to
20 Nm (15 lbf/ft).
14.Fully tighten rear fixing bolt assembly to20 Nm
(15 lbf/ft).
15.Fit spill return and fuel supply pipes to fuel tank
and securely tighten union connectios.
16.Fit electrical plug to fuel gauge unit.
17.Check that drain plug is secure and fill fuel tank.
18.Reconnect battery.
19.Prime fuel system.
See Adjustment, Priming
the fuel system
and start engine.
20.Check system for leaks and operation of fuel
gauge.
21.Fit seat base cover and seat cushion.

FUEL SYSTEM
9
REPAIR REV: 05/99
11.Remove 2 nuts that secure front fixing assembly
of the tank to chassis mounting bracket.
12.Remove tank rear mounting nuts.
13.With care, lower tank sufficiently to enable nut
and olive of spill return to be disconnected from
elbow in centre of tank.
14.Continue to lower tank until it can be removed
from vehicle.
NOTE: On later vehicles a separate stone
guard is fitted and is attached to the tank
with the existing front and rear fixings.
15.If required, remove tank gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
16.If applicable, locate stone guard under tank.
17.Raise rear tank into position and connect spill
return pipe to the elbow with the nut and olive.
18.Continue to raise tank so that front and rear
mounting bolts locate in respective tank flange
holes.
19.Fit and tighten fixings to
20 Nm (15 lbf/ft).
20.Connect fuel suppnly pipe to the tank unit.
21.Fit fuel filler hose and breather pipe to filler tube
and secure with retaining clips.
22.Fit LH lashing eye to chassis.23.Fit anti-roll bar chassis mountings.
See REAR
SUSPENSION, Repair, Anti-roll bar
24.Check that drain plug is secure and fill fuel tank.
25.Reconnect battery.
26.Prime fuel system.
See Adjustment, Priming
the fuel system
and start engine.
27.Check system for leaks and operation of fuel
gauge.