1996 LAND ROVER DEFENDER warning

ELECTRICAL
7
DESCRIPTION AND OPERATION ALARM SYSTEM FUSES
When the vehicle immobilisation and alarm system is
fitted, three fuses are used to protect the circuit:
·Alarm system 15 amp fuse, main harness, located
behind instrument binnacle.
·Alarm sounder 20 amp fuse No.10, located in main
fuse box.
·Alarm system 5 amp fuse No.20, located in main
fuse box.
The main fuse box is positioned in the centre of the
fascia, in front of the main gear lever. A label in the
fuse box cover shows the circuits protected, the fuse
rating and their locations. They are also listed below.
MAIN FUSE BOX
Fuse No. Value (amps) Electrical circuit
1 15 Hazard warning lights
2 20 Interior lamp, horn
3 15 Wipers & washers - rear
4 10 Wipers & washers - front
5 15 Heater
6 7.5 Rear fog guard lamps
7 5 Radio/cassette player
8 15 Heated rear window
9 10 Cigar lighter
10 20 Alarm sounder
11 7.5 Headlamp - RH, dipped beam
12 7.5 Headlamp - LH, dipped beam
13 7.5 Headlamp - RH, main beam
14 7.5 Headlamp - LH, main beam
15 5 Side lamps - LH
16 5 Side lamps - RH
17 15 Stop & reverse lamps
18 20 Air conditioning
19 5 Air conditioning
20 5 Alarm system

ELECTRICAL
9
DESCRIPTION AND OPERATION IMMOBILISATION AND ALARM SYSTEM CIRCUIT
DIAGRAM
1.Anti-theft alarm indicator light (LED)
2.Engine immobilisation warning light
3.Alarm system fuse - 15 amp
4.Alarm sounder relay
5.Under bonnet lighting fuse
6.Alarm sounder (without battery back-up)
7.Alarm system fuse - 5 amp (position 20)
8.Electronic control unit (ECU)
9.Bonnet switch
10.Alarm sounder protection fuse - 20 amp
(position 10)
11.Starter switch
12.Under bonnet ignition fuse
13.Driver's door switch
14.Vehicle horn switch
15.Vehicle horn
16.Passive coil
17.Starter switch relay
18.Front passenger door switch
19.Hazard warning light fuse - 15 amp (position 1)
20.Ultrasonic sensor
21.Interior lamp and horn fuse - 20 amp (position 3)
22.Alarm sounder (with battery back-up)
23.LH direction indicator lamps
24.RH direction indicator lamps
25.Interior lamp
26.Immobilisation spider
27.Rear side doors and rear door switches
28.Diagnostic connector
29.Diagnostic fuse - 7.5 amp
30.Starter solenoid
31.Fuel switch-off solenoid (injection pump)
32.Generator
33.AerialKey to cable colours
B-Black
G-Green
K-Pink
LG-Light Green
N-Brown
O-Orange
P-Purple
R-Red
S-Slate
U-Blue
W-White
Y-Yellow
The last letter of a colour code denotes the tracer
colour

ELECTRICAL
11
DESCRIPTION AND OPERATION IMMOBILISATION AND ALARM SYSTEM CIRCUIT
DIAGRAM - WITH DDS
1.Anti-theft alarm indicator light (LED)
2.Engine immobilisation warning light
3.Alarm system fuse - 15 amp
4.Alarm sounder relay
5.Under bonnet lighting fuse
6.Alarm sounder (without battery back-up)
7.Alarm system fuse - 5 amp (position 20)
8.Electronic control unit (ECU)
9.Bonnet switch
10.Alarm sounder protection fuse - 20 amp
(position 10)
11.Starter switch
12.Under bonnet ignition fuse
13.Driver's door switch
14.Vehicle horn switch
15.Vehicle horn
16.Passive coil
17.Starter switch relay
18.Front passenger door switch
19.Hazard warning light fuse - 15 amp (position 1)
20.Ultrasonic sensor
21.Interior lamp and horn fuse - 20 amp (position 3)
22.Alarm sounder (with battery back-up)
23.LH direction indicator lamps
24.RH direction indicator lamps
25.Interior lamp
26.Digital diesel shut-off valve (DDS)
27.Rear side doors and rear door switches
28.Diagnostic connector
29.Diagnostic fuse - 7.5 amp
30.Starter solenoid
31.Fuel shut-off solenoid (injection pump)
32.Generator
33.AerialKey to cable colours
B-Black
G-Green
K-Pink
LG-Light Green
N-Brown
O-Orange
P-Purple
R-Red
S-Slate
U-Blue
W-White
Y-Yellow
The last letter of a colour code denotes the tracer
colour

ELECTRICAL
1
REPAIR ELECTRICAL PRECAUTIONS
The following guidelines are intended to ensure the
safety of the operator whilst preventing damage to
electrical and electronic components fitted to the
vehicle.
Polarity
Never reverse connect the vehicle battery and always
observe the correct polarity when connecting test
equipment.
High voltage circuits
WARNING: Before commencing work on
an ignition system, all high tension
terminals, adaptors and diagnostic
equipment for testing should be inspected to
ensure that they are adequately insulated and
shielded to prevent accidental personal contacts
and minimize the risk of shock. Wearers of
surgically implanted pacemaker devices should
not be in close proximity to ignition circuits or
diagnostic equipment.
Whenever disconnecting live high tension circuits
always use insulated pliers and never allow the open
end of a high tension lead to come into contact with
other components particularly electronic control units.
Exercise caution when measuring the voltage on the
coil terminals while the engine is running, since, high
voltage spikes can occur on these terminals.
Connectors and harness
Always ensure that these items are dry and oil free
before disconnecting and connecting test equipment.
Never force connectors apart either by using tools or
by pulling on the wiring harness. Always ensure
locking tabs are disengaged before removal and note
orientation to enable correct reconnection. Ensure that
any protective covers and substances are replaced if
disturbed. Having confirmed a component to be faulty
switch-off the ignition and disconnect the battery.
Remove the component and support the disconnected
harness. When replacing the component keep oily
hands away from electrical connection areas and
push connectors home until any locking tabs fully
engage.Battery disconnecting
Before disconnecting the battery, switch off all
electrical equipment.
Battery charging
Recharge the battery out of the vehicle and keep the
top well ventilated. While being charged or
discharged, and for approximately 15 minutes
afterwards, batteries emit hydrogen gas which is
flammable. Always ensure any battery charging area
is well ventilated and that every precaution is taken to
avoid naked flames and sparks.
GENERAL PRECAUTIONS
Switch-off ignition prior to making any connection or
disconnection in the system as electrical surge
caused by disconnecting 'live' connections can
damage electronic components.
Ensure hands and work surfaces are clean and free of
grease, swarf, etc. as grease collects dirt which can
cause tracking or high-resistance contacts.
When handling printed circuit boards, treat them as
you would a disc - hold by the edges only.
Prior to commencing a test, and periodically during a
test, touch a good earth, for instance, a cigar lighter
socket, to discharge body static as some electronic
components are vulnerable to static electricity.

86ELECTRICAL
2
REPAIR BATTERY
Service repair no - 86.15.01
NOTE: If the vehicle is fitted with a battery
backed-up alarm sounder, disconnecting
the vehicle battery will cause the alarm to
sound unless the following procedure is followed:
1.Remove LH front seat cushion.
2.Release retaining clip and remove battery
access cover.
3.Slacken battery negative lead clamp bolt.
4.Turn starter switch 'on'.
5.Turn starter switch 'off' and remove key.
6.Disconnect battery WITHIN 15 SECONDS.
If alarm is accidentally activated, ensure sounder is
connected and silence by turning the starter switch to
position 'II'.Remove
WARNING: During battery removal or
before carrying out any repairs or
maintenance to electrical components
always disconnect negative lead first. If positive
lead is disconnected with negative lead in place,
accidental contact of a wrench to any grounded
metal part could cause a severe spark, possibly
resulting in personal injury. Upon installation of
battery always connect positive lead first.
1.Remove LH front seat cushion.
2.Release retaining clip and remove battery
access cover.
3.Disconnect both battery leads, negative first.
4.Slacken securing nuts and move battery clamp,
with 'J' bolts aside.
5.Remove battery.
NOTE: Coat battery clamps and terminals
with petroleum jelly before refitting.
Refit
6.Position battery and secure with clamp. Ensure
'J' bolts are hooked correctly under retaining
brackets on base of battery box.
7.Reconnect battery leads, positive lead first.
8.Fit battery access cover.
9.Fit seat cushion.

ELECTRICAL
3
REPAIR ELECTRONIC CONTROL UNIT (ECU)
Service repair no - 86.55.85
Remove
1.Remove LH front seat cushion.
2.Release retaining clip and remove battery
access cover.
3.Slacken battery negative lead clamp bolt.
4.Turn starter switch 'on'.
5.Turn starter switch 'off' and remove key.
6.Disconnect battery negative lead.
NOTE: Operation 6 needs to be carried out
within 15 seconds to avoid activating
battery backed-up alarm sounder, if fitted.
7.Remove steering wheel
See STEERING,
Repair, Steering wheel.
8.Remove 4 screws securing instrument panel to
fascia cowl
See INSTRUMENTS, Repair,
Instrument panel.
9.Pull instrument panel away from fascia cowl and
disconnect speedometer cable, multi-plugs,
alarm LED plug lead, heated rear screen lead,
gearbox oil temperature lead and immobiliser
warning light leads.
10.Remove instrument panel.
11.Remove 2 screws securing ECU to fascia cowl
(LH drive shown). On RH drive vehicles ECU is
positioned lower down, on vertical face of fascia
panel.
12.Release ECU from fascia cowl and disconnect
both multi-plugs.
13.Remove ECU.
NOTE: A new ECU must be initialised
using TestBook.
Refit
14.Position ECU at fascia cowl and reconnect both
multi-plugs.
15.Locate ECU on mounting face of fascia cowl and
secure with 2 screws.
16.Position instrument panel to fascia cowl and
reconnect immobiliser warning light leads,
gearbox oil temperature lead, heated rear screen
lead, alarm LED plug lead, multi-plugs and
speedometer cable.
17.Secure instrument panel to fascia cowl with 4
screws
See INSTRUMENTS, Repair,
Instrument panel.
18.Fit steering wheelSee STEERING, Repair,
Steering wheel.
19.Reconnect battery negative lead.
20.Fit battery access cover.
21.Fit LH seat cushion.

86ELECTRICAL
4
REPAIR HANDSET BATTERY
Service repair no - 86.77.13
Remove
1.Unlock vehicle and disarm alarm system.
2.Turn starter switch to position 'II'.
3.Turn starter switch back to position '0' and
remove key.
4.Carefully prise handset apart, starting from
keyring end, using a coin or small screwdriver.
5.Slide battery out from retaining clip.
6.Press and hold one of the handset buttons for at
least five seconds to drain any residual power
from handset.
NOTE: The engine will immobilise five
minutes after key is removed from starter
switch.Refit
7.Fit new battery into handset retaining clip with
positive side uppermost. Finger marks will
adversely affect battery life; if possible, avoid
touching flat surfaces of battery and wipe clean
before fitting.
8.Reassemble two halves of handset.
9.Press RH (Padlock) button at least four times
within range of vehicle to resynchronise handset.
10.Check operation of alarm system.
WARNING: The handset contains delicate
electronic circuits and must be protected
from impact and water damage, high
temperatures and humidity, direct sunlight and
effects of solvents, waxes and abrasive cleaners.
NOTE: New handsets must be be
initialised using TestBook.

ELECTRICAL
5
REPAIR PASSIVE COIL
Service repair no - 86.77.35
Remove
1.Remove LH front seat cushion.
2.Release retaining clip and remove battery
access cover.
3.Slacken battery negative lead clamp bolt.
4.Turn starter switch 'on'.
5.Turn starter switch 'off' and remove key.
6.Disconnect battery negative lead.
NOTE: Operation 6 needs to be carried out
within 15 seconds to avoid activating
battery backed-up alarm sounder, if fitted.
7.Remove steering wheel
See STEERING,
Repair, Steering wheel.
8.Remove 4 screws securing instrument panel to
fascia cowl
See INSTRUMENTS, Repair,
Instrument panel.
9.Pull instrument panel away from fascia and
disconnect speedometer cable, multi-plugs,
alarm LED plug lead, heated rear screen lead,
gearbox oil temperature lead and immobiliser
warning light leads.
10.Remove instrument panel.
11.Remove 7 screws securing upper and lower
halves of nacelle to steering column mounting
bracket
See STEERING, Repair, Steering
column nacelle.
12.Release multi-switch gaiters from both sides of
nacelle.
13.Remove nacelle upper and lower halves from
steering column; collect blanking grommet from
RH side.
14.Disconnect multi-plug and remove passive coil
from starter switch.
Refit
15.Feed passive coil plug lead into fascia cowl area
and reconnect multi-plug .
16.Fit coil on starter switch.
17.Position nacelle upper and lower halves to
steering column mounting bracket and secure
with 7 screws. Do not fully tighten screws at this
stage
See STEERING, Repair, Steering
column nacelle.
18.Check that passive coil is still fitted correctly on
starter switch.
19.Check fit of nacelle at starter switch and steering
column and fully tighten fixing screws.
20.Fit multi-switch gaiters to both sides of nacelle
and check that blanking grommet is located.
21.Position instrument panel to fascia cowl area
and reconnect immobiliser warning light leads,
gearbox oil temperature lead, heated rear screen
lead, alarm LED plug lead, main harness multi-
plugs and speedometer.
22.Secure instrument panel to fascia cowl with 4
screws
See INSTRUMENTS, Repair,
Instrument panel.
23.Fit steering wheelSee STEERING, Repair,
Steering wheel.
24.Reconnect battery negative lead.
25.Fit battery access cover.
26.Fit LH seat cushion.
27.Test immobilisation and alarm system.