1996 LAND ROVER DEFENDER radiator

COOLING SYSTEM
5
REPAIR 28.Secure steering pump and bracket to auxiliary
mounting bracket.
29.Fit steering pump pulley.
30.Fit drive belt
See ELECTRICAL, Repair,
Auxiliary drive belt
.
31.Fit fan cowl
See Fan cowl.
32.Fit viscous fan unit
See Viscous coupling and
fan
.
33.Fit intercooler top hose.
34.Fit radiator top hose.
35.Refill cooling system.
See Adjustment, Drain
and refill cooling system
36.Reconnect battery.THERMOSTAT
Service repair no - 26.45.01
Remove
1.Partially drain cooling system, until coolant level
is below thermostat housing.
2.Disconnect top hose from outlet elbow.
3.Disconnect electrical connections to water
temperature switch.
4.Unscrew 2 bolts and remove outlet elbow.
5.Withdraw thermostat. Note 88°C rating of
thermostat.
6.Place thermostat in a container half full of water.
Heat water and observe temperature at which
thermostat begins to open. Thermostat is
satisfactory if it opens between 85°-89°C.
Refit
7.Fit thermostat with jiggle pin/vent hole upwards.
8.Secure outlet elbow to thermostat housing.
Tighten bolts to
25 Nm (18 lbf/ft).
9.Fit water temperature switch connections.
10.Fit top hose to outlet elbow.
11.Refill cooling system.
See Adjustment, Drain
and refill cooling system

26COOLING SYSTEM
6
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Disconnect radiator bottom hose and drain
cooling system.
See Adjustment, Drain and
refill cooling system
2.Disconnect radiator top hose.
3.Remove viscous fan unit.
See Viscous
coupling and fan
4.Remove fan cowl.See Fan cowl
5.Disconnect oil cooler pipes. Plug all connections
to prevent oil spillage and ingress of dirt.
6.Disconnect top and bottom intercooler hoses.
7.Disconnect bleed hose at radiator.
8.Remove 2 bolts from both sides securing
radiator mounting brackets to bonnet platform.
9.Lift and remove radiator/intercooler assembly
from vehicle.
10.Remove 2 bolts from both sides and detach
radiator top cover from side covers.
11.Lift and remove radiator from intercooler and RH
side frame.
12.Check condition of locating grommets in radiator
top cover and lower mounting bushes. Renew if
necessary.Refit
13.Position radiator between intercooler and RH
side frame.
14.Fit radiator top cover to side covers.
15.Lower radiator/intercooler assembly into
position.
16.Secure radiator mounting brackets to bonnet
platform.
17.Fit radiator bleed hose.
18.Fit top and bottom intercooler hoses.
19.Fit oil cooler pipes.
20.Fit fan cowl
See Fan cowl.
21.Fit viscous fan unit.
See Viscous coupling
and fan
22.Fit radiator top hose.
23.Fit radiator bottom hose and refill cooling
system.
See Adjustment, Drain and refill
cooling system

37MANUAL GEARBOX
2
REPAIR
10.Remove 3 trim studs and lift up handbrake
gaiter.
11.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever. Ensure
handbrake is off.
12.Drain cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
13.Remove viscous fan unit
See COOLING
SYSTEM, Repair, Viscous coupling and fan
.
14.Slacken retaining clip and disconnect radiator
top hose at thermostat housing.
15.Slacken retaining clip and disconnect intake
hose at induction manifold. If EGR system is
fitted, slacken 2 retaining clips and disconnect
intake hose at intercooler.
16.Slacken retaining clip and disconnect hose at
turbocharger.
17.Remove bolt securing transmission breather
pipe clip to rear of engine.
18.Release breather pipes.
19.Release ties securing gearbox harness to
breather pipes.
20.Raise vehicle on ramp.
21.Position a suitable container under transmission
and drain main gearbox and transfer box
See
MAINTENANCE , Under vehicle maintenance
.
22.Mark front propeller shaft drive flange and
transfer box output flange for reassembly.
23.Remove 4 nuts and disconnect propeller shaft
from transfer box.

37MANUAL GEARBOX
6
REPAIRREV: 05/99 78.Position crossmember and locate over fixing
studs of LH and RH gearbox mounting rubbers.
79.Align crossmember and secure to chassis with 4
nuts and bolts on each side.
NOTE: Fit battery earth strap retaining clip
to LH top bolt.
80.Fit intermediate silencer.
See MANIFOLD AND
EXHAUST SYSTEM, Repair, Intermediate
pipe - 90
orSee MANIFOLD AND EXHAUST
SYSTEM, Repair, Intermediate pipe - 110/130
.
81.Fit front pipe to exhaust manifold
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust front pipe
.
82.Fit rear propeller shaft to transmission brake
drum. Tighten nuts to
47 Nm (33 lbf/ft).
83.Remove 3 bolts securing support cradle to
transmission and remove hoist.
84.Reconnect battery earth strap to transfer box
fixing.
85.Connect speedometer cable to transfer box and
secure with retaining clip.
86.Coat both sides of clutch slave clinder backing
plate with Hylomar P232M waterproof sealant.
87.Locate backing plate on slave cylinder.
88.Fit slave cylinder to bell housing, engaging
push-rod through centre of dust cover, and with
bleed screw uppermost. Tighten bolts to
25 Nm
(18 lbf/ft).
89.Fit front propeller shaft to transfer box. Tighten
nuts to
47 Nm (33 lbf/ft).
90.Refill main gearbox and transfer boxSee
MAINTENANCE , Under vehicle maintenance
.
91.Feed transmission brake cable through heel
board and ensure grommet is correctly located.
NOTE: Apply a soap solution to aid fitment
of cable.
92.Lower vehicle on ramp.
93.Fit ties to secure gearbox harness to
transmission breather pipes.
94.Fit breather pipe retaining clip to rear of engine.
95.Reconnect charge air hose at turbocharger.
96.Reconnect intake hose at induction manifold. If
EGR system is fitted, reconnect intake hose at
intercooler.
97.Reconnect radiator top hose at thermostat
housing.
98.Fit viscous fan unit
See COOLING SYSTEM,
Repair, Viscous coupling and fan
.
99.Reconnect battery.100.Refill cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
101.Connect cable clevis to handbrake lever and fit
handbrake gaiter.
102.Locate insulation pad over gear levers and fit to
tunnel cover.
103.Fit gear lever with gaiter to lower lever spline
and secure with retaining nut.
104.Fit gear lever cover.
105.Fit gear lever and transfer box lever knobs.
106.Fit gearbox cover carpet.
107.Check operation of handbrake and adjust as
necessary
See MAINTENANCE , Under
vehicle maintenance
.

HEATING AND VENTILATION
1
REPAIR HEATER UNIT
Service repair no - 80.20.01
Remove
1.Remove bonnet and disconnect battery.
2.Remove radiator bottom hose at radiator union
and drain cooling system
See COOLING
SYSTEM, Repair, Drain and refill cooling
system
.
3.Slacken clips and remove heater hoses at
heater box unions.
4.Remove outer cable securing clips.
5.Slacken trunnions and remove control cables
from heater vent flap levers.
6.Remove heater wiring harness securing loop.
7.Disconnect harness multi-plug.
8.Remove interior bulkhead trim.
9.Remove lower nuts and bolts securing the
heater unit to the bulkhead.
10.Slacken heater unit upper retaining bolts.
11.Manoeuvre heater unit, complete with blower
motor, clear of air inlet duct and remove from
engine compartment.
12.If existing heater unit is to be refitted, remove
sealing rubber.
For heater matrix removal
See Heater matrix.
For blower motor removal
See Blower motor.
Refit
13.Smear a new heater unit sealing rubber with a
suitable impact adhesive and fit to heater.
14.Manoevre heater unit into position in engine
compartment, fit blower motor to air inlet duct
and locate upper fixing bolts.
15.Loosely fit heater unit lower fixing bolts.
16.Fully tighten upper fixing bolts.
17.Fully tighten lower fixings and refit interior
bulkhead trim.
18.Secure wiring harness and reconnect multi-plug.
19.Fit control cables to vent flap trunnions and
secure with outer cable clips.
20.Connect heater hoses.
21.Fit radiator bottom hose and refill cooling system
See COOLING SYSTEM, Repair, Drain and
refill cooling system
.
22.Fit bonnet and reconnect battery.

AIR CONDITIONING
1
DESCRIPTION AND OPERATION AIR CONDITIONING SYSTEM
Description
Air conditioning is an optional system which provides
fully integrated climate control for the vehicle interior.
The air conditioning system comprises four major
units as follows:- An evaporator matrix and expansion
valve (1), housed in the heater/ cooler unit (3), an
engine mounted compressor (4), a condenser (5),mounted in front of the radiator, and a receiver/drier
(7) located to the right of the condenser.
Ancillary components in the system comprise a blower
motor (2), also housed in the heater/cooler unit, and
condenser cooling fan motors (6), mounted on a
support frame. The four major units are interconnectd
by preformed metal and flexible refrigerant pipes as
illustrated below (RH drive installation shown).
Coolant flow to a heater matrix, housed in the heater
cooler unit, is controlled by a water valve (8) from a
combined air conditioning panel on the vehicle fascia.
1.Evaporator matrix and expansion valve
2.Blower motor
3.Heater/cooler unit
4.Compressor
5.Condenser6.Condenser fan motors
7.Receiver/drier
8.Water valve
9.Heater matrix feed and return hoses

82AIR CONDITIONING
2
DESCRIPTION AND OPERATION Operation
Evaporator unit and expansion valve
High pressure liquid refrigerant is delivered to the
expansion valve which is the controlling device for the
air conditioning system. A severe pressure drop
occurs across the valve and as the refrigerant flows
through the evaporator it picks up heat from the
ambient air, boils and vaporizes. As this change of
state occurs, a large amount of latent heat is
absorbed. The evaporator is therefore cooled and as
a result heat is extracted from the air flowing across
the evaporator. The refrigerant leaves the evaporator,
on its way to the compressor, as a low pressure gas.
An evaporator sensor measures the air temperature at
the evaporator and engages or disengages the
compressor clutch to prevent icing of the air ways.
Compressor
The compressor, a pump specially designed to raise
the pressure of the refrigerant, is mounted on the front
of the engine and is driven by an independent drive
belt from the crankshaft pulley. The compressor draws
vaporized refrigerant from the evaporator. It is
compressed with a resulting rise in temperature and
passed on to the condenser as a hot, high pressure
vapour.
Condenser
The condenser is mounted directly in front of the
radiator and consists of a refrigerant coil mounted in a
series of thin cooling fins to provide the maximum
heat transfer. Air flow across the condenser is induced
by vehicle movement and assisted by two electric fans
attached to the frame of the condenser. The
refrigerant high pressure vapour enters the condenser
inlet on the RH side. As the vapour passes through
the condenser coils the air flow, assisted by the two
fans, carries the latent heat away from the condenser.
This induces a change of state resulting in the
refrigerant condensing into a high pressure warm
liquid. From the condenser, the refrigerant continues
to the receiver/ drier.
Receiver/drier
This component acts as a reservoir and is used to
hold extra refrigerant until it is needed by the
evaporator. The drier within the receiver unit contains
a filter and dessicant (drying material) which absorb
moisture and prevent dessicant dust from being
carried with the refrigerant into the system.AIR CONDITIONING AND HEATER CONTROLS -
LH DRIVE
1. Temperature control
Move the lever upwards (RED) to increase air
temperature, or downwards (BLUE) to reduce air
temperature.
2. Air conditioning switch
Press the switch (indicator lamp illuminates) to
activate the air conditioning. Press again to switch off.
3. Air recirculation control
Move the lever fully upwards to activate air
recirculation. Move the lever fully downwards to
cancel recirculation.
NOTE: Prolonged recirculation may cause
the windows to mist up.
4. Air distribution control
Lever fully up - air to windscreen vents (also provides
some air to the footwell).
Lever midway - air to fascia vents (also provides some
air to the footwell).
Lever fully down - air to footwell vents (also provides
some air to the windscreen).

82AIR CONDITIONING
6
ADJUSTMENT SYSTEM TEST
1.Place the vehicle in a ventilated, shaded area
free from excessive draught, with the doors and
windows open.
2.Check that the surface of the condenser is not
restricted with dirt, leaves, flies, etc. Do not
neglect to check the surface between the
condenser and the radiator. Clean as necessary.
3.Switch on the ignition and the air conditioner air
flow control. Check that the blower is operating
efficiently at low, medium and high speeds.
Switch off the blower and the ignition.
4.Check that the evaporator condensate drain
tubes are open and clear.
5.Check the tension of the compressor driving belt,
and adjust if necessary.
6.Inspect all connections for the presence of
refrigerant oil. If oil is evident, check for leaks,
and repair as necessary.
NOTE: The compressor oil is soluble in
Refrigerant R134a and is deposited when
the refrigerant evaporates from a leak.
7.Start the engine.
8.Set the temperature controls to cold and switch
the air conditioner blower control on and off
several times, checking that the magnetic clutch
on the compressor engages and releases each
time.
9.With the temperature control at maximum
cooling and the blower control at high speed,
warm up the engine and fast idle at 1000
rev/min.
10.Repeat at 1800 rev/min.
11.Gradually increase the engine speed to the high
range and check the sight glass at intervals.
12.Check for frosting on the service valves.
13.Check the high pressure hoses and connections
by hand for varying temperature. Low
temperature indicates a restriction or blockage at
that point.
14.Switch off the air conditioning blower and stop
the engine.
15.If the air conditioning equipment is still not
satisfactory, carry out a pressure test as
previously described in this section.PRECAUTIONS IN HANDLING REFRIGERANT
LINES
WARNING: Wear eye and hand protection
when disconnecting components
containing refrigerant. Plug all exposed
connections immediately.
1.When disconnecting any hose or pipe
connection the system must be discharged of all
pressure. Proceed cautiously, regardless of
gauge readings. Open connections slowly,
keeping hands and face well clear, so that no
injury occurs if there is liquid in the line. If
pressure is noticed, allow it to bleed off slowly.
2.Lines, flexible end connections and components
must be capped immediately they are opened to
prevent the entrance of moisture and dirt.
3.Any dirt or grease on fittings must be wiped off
with a clean alcohol dampened cloth. Do not use
chlorinated solvents such as trichloroethylene. If
dirt, grease or moisture cannot be removed from
inside the hoses, they must be replaced with
new hoses.
4.All replacement components and flexible end
connections must be sealed, and only opened
immediately prior to making the connection.
5.Ensure the components are at room temperature
before uncapping, to prevent condensation of
moisture from the air that enters.
6.Components must not remain uncapped for
longer than 15 minutes. In the event of delay, the
caps must be fitted.
7.Receiver/driers must never be left uncapped as
they contain Silica Gel crystals which will absorb
moisture from the atmosphere. A receiver/ drier
left uncapped must not be used, fit a new unit.
8.The compressor shaft must not be rotated until
the system is entirely assembled and contains a
charge of refrigerant.
9.A new compressor contains an initial charge of
refrigerant oil. The compressor also contains a
holding charge of gas when received which
should be retained by leaving the seals in place
until the pipes are re-connected.
10.The receiver/drier should be the last component
connected to the system to ensure optimum
dehydration and maximum moisture protection of
the system.