1996 LAND ROVER DEFENDER service

HEATING AND VENTILATION
7
REPAIR Refit
14.Fit new control cable through heater duct cover
and secure to vent flap trunnion. Bend over
cable end to fully secure.
15.Fit heater duct cover.
16.Fit lower fascia panel assembly to fascia
bulkhead
See CHASSIS AND BODY, Repair,
lower fascia panel (heater duct) assembly.
17.Route control cable along fascia bulkhead to
contol lever assembly.
18.With control lever in closed position, secure
cable to clevis.
19.Fit outer cable retaining clip to lever assembly.
20.Fit lever assembly to side cover. Ensure screw
spacers are fitted between cover and lever
assembly.
21.Fit side cover to fascia cowl.
22.Fit control lever knobs.
23.Fit instrument panel
See INSTRUMENTS,
Repair, Instrument panel.
24.Fit steering column nacelleSee STEERING,
Repair, Steering column nacelle.
CONTROL CABLE AND BLOWER MOTOR SWITCH
Service repair no - 80.10.17 - Control cable
Service repair no - 80.10.22 - Blower motor switch
Remove
1.Disconnect battery.
2.From inside engine compartment, release outer
cable retaining clip at heater unit.
3.Slacken trunnion fixing and release inner cable
from heater unit flap lever.
4.Release 2 retaining clips securing control cables
to engine bulkhead and heater hoses.
5.Remove 4 screws securing instrument panel to
fascia cowl.
6.Pull instrument panel away from fascia and
disconnect speedometer cable to ease access to
control cable.
7.Remove 2 screws securing control lever
assembly to side of fascia panel cowl. Note
plastic screw spacers fitted between cowl and
lever assembly and retain.

82AIR CONDITIONING
4
ADJUSTMENT 5.Operate the refrigerant recharging system
according to the manufactures instructions.
Refrigerant to charge system is 1.1 kg.
6.If the full charge has not been accepted by the
system, start the engine and run it at 1500
rev/min for a minimum of 2 minutes.
Switch on the air conditioning system, open the
vehicle windows, set the temperature control to
cold and switch the blower to maximum speed.
7.Consult Refrigerant Station Manual for correct
procedure to complete the charge.
8.Carry out the air conditioning system
performance test.LEAK TEST SYSTEM
The following instructions refer to an electronic type
Refrigerant Leak Detector for use with R134a, which
is the safest and most sensitive.
CAUTION: When a major repair has been
carried out, a leak test should be carried
out using an inert gas (see below).
1.Place the vehicle in a well ventilated area but
free from draughts, as leakage from the system
could be dissipated without detection.
2.Follow the instructions issued by the
manufacturer of the particular leak detector
being used.
3.Commence searching for leaks by passing the
detector probe around all joints and components,
refrigerant gas is heavier than air.
4.Insert the probe into an air outlet of the
evaporator or into the evaporator drain tube.
Switch the air conditioning blower on and off at
intervals of ten seconds. Any leaking refrigerant
will be gathered in by the blower and detected.
5.Insert the probe between the magnetic clutch
and compressor to check the shaft seal for
leaks.
6.Check all service valve connections, valve plate,
head and base plate joints and back seal plate.
7.Check the condenser for leaks at the pipe
unions.
8.If any leaks are found, the system must be
discharged before rectification.
9.Rectify any leaks and recheck for leaks during
evacuation prior to charging.
Leak test using inert gas
Use Nitrogen or Helium gas.
1.Connect gas line to recharging station.
2.Pressurise system to 3 bar.
3.Carry out leak test as above.

82AIR CONDITIONING
6
ADJUSTMENT SYSTEM TEST
1.Place the vehicle in a ventilated, shaded area
free from excessive draught, with the doors and
windows open.
2.Check that the surface of the condenser is not
restricted with dirt, leaves, flies, etc. Do not
neglect to check the surface between the
condenser and the radiator. Clean as necessary.
3.Switch on the ignition and the air conditioner air
flow control. Check that the blower is operating
efficiently at low, medium and high speeds.
Switch off the blower and the ignition.
4.Check that the evaporator condensate drain
tubes are open and clear.
5.Check the tension of the compressor driving belt,
and adjust if necessary.
6.Inspect all connections for the presence of
refrigerant oil. If oil is evident, check for leaks,
and repair as necessary.
NOTE: The compressor oil is soluble in
Refrigerant R134a and is deposited when
the refrigerant evaporates from a leak.
7.Start the engine.
8.Set the temperature controls to cold and switch
the air conditioner blower control on and off
several times, checking that the magnetic clutch
on the compressor engages and releases each
time.
9.With the temperature control at maximum
cooling and the blower control at high speed,
warm up the engine and fast idle at 1000
rev/min.
10.Repeat at 1800 rev/min.
11.Gradually increase the engine speed to the high
range and check the sight glass at intervals.
12.Check for frosting on the service valves.
13.Check the high pressure hoses and connections
by hand for varying temperature. Low
temperature indicates a restriction or blockage at
that point.
14.Switch off the air conditioning blower and stop
the engine.
15.If the air conditioning equipment is still not
satisfactory, carry out a pressure test as
previously described in this section.PRECAUTIONS IN HANDLING REFRIGERANT
LINES
WARNING: Wear eye and hand protection
when disconnecting components
containing refrigerant. Plug all exposed
connections immediately.
1.When disconnecting any hose or pipe
connection the system must be discharged of all
pressure. Proceed cautiously, regardless of
gauge readings. Open connections slowly,
keeping hands and face well clear, so that no
injury occurs if there is liquid in the line. If
pressure is noticed, allow it to bleed off slowly.
2.Lines, flexible end connections and components
must be capped immediately they are opened to
prevent the entrance of moisture and dirt.
3.Any dirt or grease on fittings must be wiped off
with a clean alcohol dampened cloth. Do not use
chlorinated solvents such as trichloroethylene. If
dirt, grease or moisture cannot be removed from
inside the hoses, they must be replaced with
new hoses.
4.All replacement components and flexible end
connections must be sealed, and only opened
immediately prior to making the connection.
5.Ensure the components are at room temperature
before uncapping, to prevent condensation of
moisture from the air that enters.
6.Components must not remain uncapped for
longer than 15 minutes. In the event of delay, the
caps must be fitted.
7.Receiver/driers must never be left uncapped as
they contain Silica Gel crystals which will absorb
moisture from the atmosphere. A receiver/ drier
left uncapped must not be used, fit a new unit.
8.The compressor shaft must not be rotated until
the system is entirely assembled and contains a
charge of refrigerant.
9.A new compressor contains an initial charge of
refrigerant oil. The compressor also contains a
holding charge of gas when received which
should be retained by leaving the seals in place
until the pipes are re-connected.
10.The receiver/drier should be the last component
connected to the system to ensure optimum
dehydration and maximum moisture protection of
the system.

AIR CONDITIONING
1
REPAIR COMPRESSOR
Service repair no - 82.10.20
Remove
1.Disconnect battery.
2.Recover refrigerant from air conditioning system
See Adjustment, Refrigerant recovery,
recycling, recharging.
3.Remove compressor drive belt.See
Compressor drive belt
4.Disconnect high pressure pipe from compressor.
5.Disconnect low pressure pipe from compressor.
6.Remove 'O' ring from each flange.
7.Disconnect compressor clutch harness
multi-plug.
8.Remove compressor from mounting bracket
studs.Refit
9.If a new compressor is to be fitted first drain oil
from new compressor. Drain and measure oil
from old compressor. Measure new oil equal to
amount from old compressor, add 30 ml extra to
this amount and refill new compressor through
outlet port.
10.Locate compressor over mounting bracket studs.
11.Reconnect compressor clutch harness
multi-plug.
12.Fit new 'O' rings to high and low pressure hose
flanges, lubricate with refrigerant oil.
13.Fit high and low pressure hoses.
14.Fit compressor drive belt
See Compressor
drive belt.
15.Evacuate and recharge air conditioning system
See Adjustment, Refrigerant recovery,
recycling, recharging.
16.Reconnect battery.
17.Perform a leak test on disturbed joints.
18.Carry out a functional check.

82AIR CONDITIONING
2
REPAIR COMPRESSOR DRIVE BELT
Service repair no - 82.10.02
Remove
1.Disconnect battery.
2.Remove auxiliary drive belt
See ELECTRICAL,
Repair, Auxiliary drive belt.
3.Remove 3 nuts securing drive belt guard to
compressor retaining studs.
4.Slacken 3 belt tensioner retaining bolts.
5.Remove compressor drive belt. Mark direction
on belt if refitting.Refit
6.Fit compressor drive belt.
7.Fit drive belt guard.
8.Fit torque meter to centre of tensioner, apply and
hold a torque of
35 Nm (26 lbf/ft).
9.Tighten tensioner retaining bolts.
10.Rotate crankshaft 2 full turns.
11.Reapply and hold a torque of
35 Nm (26 lbf/ft)
to tensioner, then fully slacken and retighten
tensioner retaining bolts to
25 Nm (18 lbf/ft).
12.Fit auxiliary drive beltSee ELECTRICAL,
Repair, Auxiliary drive belt.
13.Reconnect battery.

AIR CONDITIONING
3
REPAIR CONDENSER FAN AND MOTORS
Service repair no - 82.15.08
Remove
1.Disconnect battery.
2.Remove 6 screws and lift grille panel from
vehicle.
3.Disconnect fan motor multi-plugs and release
harness retaining clips.
4.Remove nut and washers and withdraw fan
blade from motor drive shaft.
5.Remove 2 retaining screws, release motor fan
from shroud support brackets and feed motor
multi-plug lead through appropriate aperture.
Refit
6.Feed motor lead through fan shroud.
7.Fit motor to fan shroud support brackets.
8.Reconnect fan lead multi-plug and secure with
retaining clips.
9.Fit fan blade to motor drive shaft.
10.Fit grille panel.
11.Reconnect battery.CONDENSER
Service repair no - 82.15.07
Remove
1.Disconnect battery.
2.Recover refrigerant from air conditioning system
See Adjustment, Refrigerant recovery,
recycling, recharging.
3.Remove 6 screws and lift grille panel from
vehicle .
4.Disconnect condenser fan motor lead
multi-plugs.
5.Disconnect receiver/drier dual pressure switch
multi-plug.
6.Disconnect condenser low pressure pipe at
compressor.
7.Disconnect high pressure hose/pipe at
evaporator.

AIR CONDITIONING
5
REPAIR RECEIVER/DRIER
Service repair no - 82.17.01
Remove
1.Disconnect battery.
2.Recover refrigerant from air conditioning system
See Adjustment, Refrigerant recovery,
recycling, recharging.
3.Remove 6 screws and lift grille panel from
vehicle.
4.Disconnect receiver/drier dual pressure switch
multi-plug.
5.Disconnect high pressure pipe at receiver/drier.
6.Disconnect bottom union at condenser.
7.Remove retaining bolts and open clamps.
8.Release receiver/drier from condenser and
discard. It is NOT recommended to refit old unit.
9.Discard all pipe connection 'O' rings. Cap or plug
all connections to prevent ingress of dirt and
moisture.
Refit
10.Coat unions, threads and new 'O' rings with
refrigerant oil prior to reassembly.
11.Secure new receiver/drier in retaining clamp.
12.Fit receiver/drier bottom union connector at
condenser.
13.Fit high pressure pipe to receiver/drier.
14.Fit pressure switch multi-plug.
15.Evacuate and recharge air conditioning system
See Adjustment, Refrigerant recovery,
recycling, recharging.
16.Reconnect battery.
17.Fit grille panel assembly.HEATER/COOLER UNIT - LH DRIVE
Service repair no - 82.25.21
Remove
1.Disconnect battery.
2.Recover refrigerant from air conditioning system
See Adjustment, Refrigerant recovery,
recycling, recharging.
3.Remove expansion tankSee COOLING
SYSTEM, Repair, Expansion tank
to gain
access to air conditioning high and low pressure
pipes.
4.Disconnect high and low pressure pipes. Discard
pipe connection 'O' rings. Cap or plug
connections to prevent ingress of dirt and
moisture.
5.Disconnect compressor clutch switch multi-plug.
6.Remove pipe connector from vacuum switch.
7.Remove retaining clip and disconnect control
cable from evaporator flap operating rod.
8.Remove screw and release outer cable retaining
bracket.

AIR CONDITIONING
7
REPAIR EVAPORATOR - LH DRIVE
Service repair no - 82.25.20
Remove
1.Remove heater/cooler unit
See Heater/cooler
unit.
2.Suitably support unit on a bench to prevent
damage to heater matrix pipes.
3.Release 3 nuts and remove mounting bracket
from underneath unit casing.
4.Remove 7 screws securing outlet duct to
heater/cooler unit.
5.Carefully break sealing compound around edge
of duct and pull ducting from unit.
6.Remove 15 screws located around cover seam.
Break sealing compound from unit body and top
cover.
7.Remove 4 screws and 4 nuts from top of cover.
8.From front of unit remove 2 screws adjacent to
low pressure pipe moulding.
9.At side of unit remove 2 screws adjacent to air
intake aperture.
10.Lift off top cover, release grommet and feed
blower motor wiring and air control flap rod
through respective apertures. Note thermostat
temperature probe which is inserted in
evaporator matrix through top cover.
11.Lift support plate and insulation pad from heater
matrix.
12.From bottom of unit casing, remove 3 screws
adjacent to dump valve outlet, and screws next
to heater matrix pipes.