1996 LAND ROVER DEFENDER torque

ENGINE
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine block
Bearing cap 133...............................................................................................
Blanking plug, oil gallery, rear 37....................................................................
Oil squirt jet assembly 17................................................................................
Drain plug, cylinder block 25...........................................................................
Oil squirt jet, vacuum pump cam 7.................................................................
Connecting rod to cap 59................................................................................
Oil pick up assembly to bearing cap 9...........................................................
Oil pick up assembly to front cover 25............................................................
Camshaft thrust plate 9..................................................................................
Oil drain pipe to block (internal) 25.................................................................
Oil drain pipe to block (external) 25................................................................
Sump to cylinder block and front cover 25......................................................
Drain plug, oil sump 35...................................................................................
Tappet guide 14..............................................................................................
Breather side cover assembly 25....................................................................
Baffle plate to breather side cover 4..............................................................
Vacuum pump 25............................................................................................
Fuel lift pump 25.............................................................................................
Flywheel housing 45.......................................................................................
Flywheel housing clutch cover stud 10...........................................................
Plug, flywheel housing 12...............................................................................
Rear oil seal assembly 25...............................................................................
Oil filter adaptor 45..........................................................................................
Waxstat adaptor to oil filter adaptor 9............................................................
Oil pressure switch 17.....................................................................................
Oil filter, spin on 13.........................................................................................
Oil cooler unions to filter adaptor 45...............................................................
Oil level tube 25..............................................................................................
Engine mounting foot to cylinder block 85......................................................
Engine mounting foot to flywheel housing 45.................................................
Engine mounting foot rubber to mounting foot (bolt and nut) 85.....................
Flywheel to crankshaft 146..............................................................................
Clutch cover plate to flywheel 34....................................................................
Flex drive plate to crankshaft (auto) 146..........................................................
Flex drive plate to ring gear (auto) 25.............................................................
Flex drive plate to torque converter (auto) 45.................................................

12ENGINE
2
SPECIFICATIONS, TORQUE REV: 05/99Nm
Cylinder head
Cylinder head to cylinder block
M10 x 117 40 Nm + 60° ..........................................................................................
M12 x 100 40 Nm + 60° ..........................................................................................
M12 x 140 40 Nm + 60°+20° ......................................................................................
Stub pipe heater feed 22.................................................................................
Water temperature sensor 14.........................................................................
Blanking plug cylinder head 14.......................................................................
Engine lifting brackets 25................................................................................
Electrical harness clip bracket 25...................................................................
Exhaust manifold stud 10................................................................................
Exhaust manifold nut 45.................................................................................
Inlet manifold stud 8.......................................................................................
Inlet manifold nut and bolt 25..........................................................................
Air temperature sensor, inlet manifold 14.......................................................
Blanking plug, inlet manifold 14......................................................................
Heatshield to inlet manifold 6.........................................................................
Glow plug 20...................................................................................................
Glow plug terminal nut 2................................................................................
Injector clamp (stud) 8...................................................................................
Injector clamp (nut) 25....................................................................................
Thermostat housing 25...................................................................................
Water outlet elbow to thermostat housing 25..................................................
Water temperature switch, thermostat housing 11..........................................
Plug thermostat housing 6.............................................................................
Rocker shaft pedestal bolt 5 Nm + 50° ..................................................................
Rocker cover (stud) 8.....................................................................................
Rocker cover (fixing nut) 10............................................................................
Breather cyclone to rocker cover 9................................................................
Tappet adjusting nut 16..................................................................................
Front cover to cylinder block 25......................................................................
Front cover plate to front cover 25..................................................................
Static idler - timing belt (stud) 10.....................................................................
Static idler - timing belt (nut) 45......................................................................
Tensioner (timing belt) 45...............................................................................
Camshaft hub bolt 80......................................................................................
Timing pulley to camshaft hub 25...................................................................
Fuel injection pump (stud) 8...........................................................................
Fuel injection pump (nut) 25...........................................................................
Abutment bracket to injection pump 25...........................................................
Support bracket injection pump to cylinder block 25.......................................
Fuel injection pump access plate to front cover plate 25................................
Timing pulley to injection pump hub 25...........................................................
TV Damper pulley bolt to crankshaft 80 Nm + 90° ..................................................
Fan pulley to hub 25.......................................................................................
Fan and viscous coupling to hub 45...............................................................
Auto tensioner, auxiliary drive (stud) 14..........................................................
Auto tensioner, auxiliary drive (nut) 45...........................................................
Auxiliary mounting bracket to cylinder block (stud) 8.....................................
Auxiliary mounting bracket to cylinder block (bolt and nut) 25........................
Water pump to block and mounting plate 25..................................................
Water pump pulley to hub 25..........................................................................

ENGINE
3
SPECIFICATIONS, TORQUENm
Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor 25........................................................
Oil feed pipe to turbocharger 19.....................................................................
Turbocharger to cylinder head (stud) 10.........................................................
Turbocharger to cylinder head (nut) 45...........................................................
Turbocharger to blanking plate 25..................................................................
Turbocharger to EGR valve 25.......................................................................
EGR delivery tube to valve 25........................................................................
EGR delivery tube to mixing tube 25..............................................................
Fuel lift pump to filter (union) 15.....................................................................
Fuel filter from lift pump (banjo bolt) 33...........................................................
Fuel filter to fuel injection pump (banjo bolt) 33..............................................
Fuel injection pump from fuel filter (banjo bolt) 25..........................................
Injector pipes to injectors and fuel injection pump 29.....................................
Spill rail to injectors (banjo bolt) 10.................................................................
Spill rail to injection pump (banjo bolt) 25.......................................................
Boost pipe injection pump (banjo bolt) 10.......................................................
Plug, rear of injection pump 29.......................................................................
PAS pump to mounting plate 25.....................................................................
PAS pump mounting plate to auxiliaries mounting bracket 25........................
PAS pump pulley to hub 25............................................................................
Starter motor (bolt and nut) 45........................................................................
Air conditioning compressor
Compressor mounting bracket to front cover 45.............................................
Compressor to mounting bracket (stud) 8......................................................
Compressor to mounting bracket (nut) 25......................................................
Belt tensioner pulley to tensioner arm 45........................................................
Belt tensioner assembly to front cover plate 25..............................................
Idler pulley to front cover plate 45...................................................................
Compressor belt guard (nut) 25......................................................................
Sensors to water outlet elbow (air/con) 25......................................................
Blanking plug, water outlet elbow (air/con) 25................................................
Generator
Generator mounting bracket to front cover 45................................................
Generator to mounting bracket 85..................................................................
Generator pulley to hub 95.............................................................................
Generator belt guard 25..................................................................................
Generator to auxiliaries mounting bracket 25.................................................
Tachometer electrical connection 4...............................................................

12ENGINE
4
SPECIFICATIONS, TORQUEMETRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................
NOTE: Torque values above are to be used as a guide where no torque is specified.

26COOLING SYSTEM
4
DESCRIPTION AND OPERATION Operation
To engage and disengage the fan drive the bi-metal
coil senses air temperature behind the radiator. When
a pre-determined temperature is reached, the coil
opens a valve (5) which allows fluid to enter the drive
area and, due to centrifugal force, circulates to the
annular drive area.
There are two sets of annular grooves (3), one in the
drive clutch and the other in the drive body, a specific
clearance being provided between the two sets of
grooves.
Viscous unit disengaged (engine at normal
running temperature)
1.Input (drive) member
2.Output (driven) member
3.Running clearance
4.Pump plate
5.Valve (closed)
6.Sensing mechanism (bi-metal coil)
7.Fluid seal
8.Bearing, input member
9.Fluid chamber
10.Fluid reservoirWhen this clearance is filled with viscous fluid, a
shearing action, caused by the speed differential
between the two drive components, transmits torque
to the fan. The fluid is thrown to the outside of the unit
by centrifugal force from where it is recirculated to the
reservoir (10) via the pump plate (4) adjacent to the
drive member.
If the engine speed is increased the amount of slip will
also increase to limit the maximum fan speed.
When the air temperature from the radiator drops
sufficiently, the bi-metal coil closes the valve and
prevents fluid entering the drive area. The fluid that is
in the drive area will gradually pump out into the
reservoir (10) and the fan will return to an idle
condition.
Viscous unit engaged (hot running temperature)
Bi-metal coil (6) expanded, valve (5) open.

COOLING SYSTEM
1
REPAIR VISCOUS COUPLING AND FAN
Service repair no - 26.25.19 - Viscous coupling
Service repair no - 26.25.05 - Fan
Remove
NOTE: The viscous coupling has a LH
thread.
1.Disconnect battery.
2.Using special pulley restraining toolLRT-12-094
and special spannerLRT-12-093unscrew
viscous coupling from pulley hub adaptor thread.
3.Remove viscous coupling and fan from vehicle.
NOTE: If air conditioning is fitted, the fan
cowl will also need removing,
See Fan
cowl
, with the viscous fan unit.
4.If required, remove 4 screws and release
viscous unit from fan blade.
Refit
5.Fit viscous unit to fan blades.
6.If applicable, fit fan cowl.
See Fan cowl
7.Carefully position viscous coupling and fit onto
pulley hub adaptor thread.
8.Using special pulley retaining tool, spanner and
a suitable torque wrench, tighten assembly to
45
Nm (33 lbf/ft).

MANUAL GEARBOX
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Slave cylinder to bell housing 25....................................................................
Breather 15.....................................................................................................
Bell housing to cylinder block 40.....................................................................
High/low level to shaft 2.................................................................................
Transfer box to gearbox 45.............................................................................
NOTE: Torque values below apply to all screws and bolts used unless otherwise specified.
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................

TRANSFER GEARBOX
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Transfer gearbox
Pinch bolt - operating arm to crank arm 9......................................................
End cover gear change housing 9.................................................................
Bottom cover to transfer case 25....................................................................
Front output housing to transfer case 25........................................................
Cross shaft housing to front output housing 25...............................................
Gear change housing 25.................................................................................
Pivot shaft to link arm 25.................................................................................
Connecting rod to adjustable clevis 25...........................................................
Anti-rotation plate intermediate shaft 25.........................................................
Front output housing cover 25........................................................................
Pivot bracket to extension housing 25............................................................
Finger housing to front output housing 25......................................................
Bearing housing to transfer case 25...............................................................
Brake drum to coupling flange 25...................................................................
Bearing housing cover to transfer gearbox 45................................................
Rear output speedometer housing to transfer gearbox 45..............................
Selector finger to cross shaft high/low 25.......................................................
Selector fork, high/low to shaft 25...................................................................
Transmission brake to speedometer housing 72............................................
Gate plate to grommet plate 9.......................................................................
Gearbox to transfer case 45...........................................................................
Oil drain plug 30..............................................................................................
Oil filler/level plug 30.......................................................................................
Differential case (front to rear) 60...................................................................
Output flanges 162...........................................................................................
Differential case rear stake nut 72..................................................................
Transfer breather 15.......................................................................................
Transfer box front drive flange to drive shaft 45..............................................
Transfer box rear drive flange to drive shaft 45..............................................
Transfer gearbox mounting brackets to chassis 30........................................
Mounting brackets to transfer gearbox 55......................................................
Mounting rubbers to mounting brackets 21.....................................................