1996 LAND ROVER DEFENDER suspension

19FUEL SYSTEM
8
REPAIR REAR MOUNTED FUEL TANK - 110/130
Service repair no - 19.55.26
WARNING: Before any attempt is made to
start the removal procedure it is vital that
the FUEL HANDLING PRECAUTIONS
See
INTRODUCTION, Information, FUEL HANDLING
PRECAUTIONS
are carefully studied and
implemented in the interests of safety.
Remove
1.Disconnect battery.
2.Remove fuel filler cap.
3.Remove tank drain plug, allow fuel to drain into a
clean container, and refit plug.
4.Slacken retaining clips and disconnect fuel filler
hose from rear tank.5.Disconnect breather hose from filler tube.
6.Disconnect electrical plug and fuel supply pipe
from outlet pipe union on fuel gauge unit.
7.If the vehicle is fitted with a tow ball drop-plate
with support bars, the bars must be removed.
8.Remove anti-roll bar chassis mountings.
See
REAR SUSPENSION, Repair, Anti-roll bar
and push roll bar down to provide access to the
tank.
9.Remove LH lashing eye to assist access to tank.
10.Position a support under the tank, preferably one
that can be progressively lowered.

FUEL SYSTEM
9
REPAIR REV: 05/99
11.Remove 2 nuts that secure front fixing assembly
of the tank to chassis mounting bracket.
12.Remove tank rear mounting nuts.
13.With care, lower tank sufficiently to enable nut
and olive of spill return to be disconnected from
elbow in centre of tank.
14.Continue to lower tank until it can be removed
from vehicle.
NOTE: On later vehicles a separate stone
guard is fitted and is attached to the tank
with the existing front and rear fixings.
15.If required, remove tank gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
16.If applicable, locate stone guard under tank.
17.Raise rear tank into position and connect spill
return pipe to the elbow with the nut and olive.
18.Continue to raise tank so that front and rear
mounting bolts locate in respective tank flange
holes.
19.Fit and tighten fixings to
20 Nm (15 lbf/ft).
20.Connect fuel suppnly pipe to the tank unit.
21.Fit fuel filler hose and breather pipe to filler tube
and secure with retaining clips.
22.Fit LH lashing eye to chassis.23.Fit anti-roll bar chassis mountings.
See REAR
SUSPENSION, Repair, Anti-roll bar
24.Check that drain plug is secure and fill fuel tank.
25.Reconnect battery.
26.Prime fuel system.
See Adjustment, Priming
the fuel system
and start engine.
27.Check system for leaks and operation of fuel
gauge.

33CLUTCH
2
FAULT DIAGNOSIS FAULT/SYMPTOM CHART
Symptoms
Slip Spin/Drag Judder/Fierce Fault Item
* * * Worn or oil on clutch linings 2
* * * Mechanical damage45678
* * Distorted clutch plate 2
* Failed or air in hydraulic system 12 13
* * Primary shaft tight fit in crankshaft bush 15 17
* Clutch splines sticking 2 15
* Weak clutch plate springs or insecure/worn
engine/gearbox mountings6
* Insecure/worn propeller shafts
* Insecure/worn suspension components/rubber
bushes
The items refered to in this chart relate to the clutch components shown in J6270 and J6271.See Description
and operation, Description
CLUTCH NOISE - MECHANICAL FAULTS
Noise from clutch or gearbox in neutral, which
disappears when clutch is depressed.
Suspect gearbox input/primary shaft bearings
See MANUAL GEARBOX, Fault diagnosis,
R380 gearbox
.
Noise from clutch or gearbox in neutral, which
changes tone or becomes worse when the clutch
is depressed.
Suspect worn release bearing.
Knocking/rattling from clutch or gearbox in
neutral, which is reduced or disappears when the
clutch is depressed.
Suspect worn/weak release lever retainer or
clutch unit.
Noise from clutch or gearbox in neutral, which
disappears when clutch is depressed.
Suspect gearbox fault
See MANUAL
GEARBOX, Fault diagnosis, R380 gearbox
.HYDRAULIC FAULTS
Unable to dis-engage clutch, little or no pedal
resistance.
1.Check condition, specification and level of fluid.
2.Check pipes and cylinders for leaks.
3.Check that air vent in reservoir lid is clear.
Suspect faulty master cylinder if no fluid leaks
present
See Repair, Master cylinder.
Spongy pedal operation
1.Check condition, specification and level of fluid.
2.Check that air vent in reservoir lid is clear.
Suspect air in fluid
See Repair, Bleed
hydraulic system
.
Clutch is difficult to dis-engage and/or does not
immediately re-engage when pedal is released.
1.Check condition, specification and level of fluid.
2.Check that air vent in reservoir lid is clear.
Suspect pedal pivot, master cylinder or slave
cylinder seizure
See Repair, Master cylinder.

REAR AXLE AND FINAL DRIVE
1
REPAIR REAR AXLE
Service repair no - 51.25.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
the axle when lowering or repositioning
axle.
1.Drain brake system.
2.Support chassis rear.
3.Remove road wheels.
4.Support axle weight with hydraulic jack.
5.Disconnect shock absorbers.
6.Disconnect flexible brake hose at RH chassis
side member and breather hose at banjo
connection on axle casing.
7.Disconnect lower links at axle.8.Mark differential and propeller shaft flanges with
identification marks for assembly.
9.Remove 4 nuts and bolts, lower propeller shaft
and tie to one side.
10.Disconnect pivot bracket ball joint at axle
bracket.
11.Release bolts and remove coil spring retaining
plates.
12.Lower axle and remove road springs.
13.If applicable, remove anti-roll bar links at axle
See REAR SUSPENSION, Repair, anti-roll
bar
.
14.Remove axle assembly.

51REAR AXLE AND FINAL DRIVE
2
REPAIRREV: 05/99 Refit
15.Position axle and fit lower links. Tighten fixings
to
176 Nm (130 lbf/ft).
16.If applicable, fit anti-roll bar links to axleSee
REAR SUSPENSION, Repair, Anti-roll bar
links
.
17.Raise axle and locate road springs.
18.Fit coil spring retaining plates and secure with
fixing bolts.
19.Secure pivot bracket ball joint to axle bracket.
Tighten fixing to
176 Nm (130 lbf/ft).
20.Align propeller shaft to differential drive flange
and tighten fixings to
47 Nm (35 lbf/ft).
21.Reconnect flexible brake hose and axle breather
hose.
22.Refit shock absorbers.
23.Fit road wheels and tighten to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy Duty wheels -170 Nm (125 lbf/ft)
24.Remove rear chassis support.
25.Bleed brake system
See BRAKES, Repair,
brake system bleed
.

FRONT AXLE AND FINAL DRIVE
1
REPAIR REV: 05/99 FRONT AXLE ASSEMBLY
Service repair no - 54.10.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
axle when lowering or repositioning axle.
1.Support chassis front.
2.Remove road wheels.
3.Support axle weight with hydraulic jack.
4.Remove radius arms to chassis frame nuts.
5.Disconnect steering damper from track rod.
Using a extractor remove track rod links from
swivel pin arms.
6.Remove four nuts and bolts securing radius
arms to axle bracket.
7.Remove radius arms.
8.Remove bolts securing brake hose brackets .
Refit bolts to prevent oil leakage.
9.Remove bolts from brake calipers and tie to one
side.
10.Remove nuts and washers securing shock
absorbers to axle.
11.Disconnect drag link from swivel pin housing
arm.
12.Remove two nuts and bolts securing panhard
rod to axle bracket. Lift rod clear of axle.
13.Mark for reassembly drive shaft flanges.
Remove four nuts and bolts, tie propeller shaft to
one side.
14.Release axle ventilation pipe banjo and lower
axle assembly. Remove road springs.
15.Disconnect anti-roll bar link
See FRONT
SUSPENSION, Repair, Anti-roll bar ball
.
16.Remove axle assembly.
Refit
17.Position axle under vehicle, supporting left side
of axle, and fit anti-roll bar links
See FRONT
SUSPENSION, Repair, Anti-roll bar links
.
18.Fit propeller shaft. Tighten bolts to
47 Nm (35
lbf/ft).
19.Fit panhard rod to axle bracket. Tighten bolts to
88 Nm (65 lbf/ft).
20.Fit drag link to swivel pin arm. Tighten fixings to
40 Nm (30 lbf/ft).
21.Fit shock absorbers to axle.
22.Fit brake calipers. Tighten bolts to
82 Nm (60
lbf/ft).
23.Tighten upper swivel pin bolts to78 Nm (58
lbf/ft).
24.Fit radius arms to axle brackets. Tighten bolts to
197 Nm (145 lbf/ft).
25.Fit steering damper to track rod.
26.Fit radius arms to chassis side member. Tighten
fixings to
197 Nm (145 lbf/ft).
27.Tighten track rod end to40 Nm (30 lbf/ft)and fit
new split pin.
28.Remove chassis supports, fit road wheels and
tighten to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)

STEERING
3
FAULT DIAGNOSIS STEERING DAMPER
The power steering system, as well as reducing the
effort required to manoeuvre the vehicle when
parking, also helps to dampen any deflections of the
road wheels, being transmitted back to the steering
wheel.
When operating the vehicle off road, the road wheels
are often deflected by ruts and boulders causing the
steering wheel to turn left and right. This phenomenon
is known as 'steering kickback'. To subdue the effects
of 'steering kickback', a hydraulic damper is fitted in
the steering linkage between the track rod and the
differential casing. The damper, which offers the same
resistance in extension and compression, is sealed for
life.
Steering damper check
Check the condition operation of the hydraulic
steering damper as follows:
Check procedure
1.Inspect damper for casing damage or leaks.
2.Clamp one end of the damper horizontally in a
vice using soft jaws. Compress and extend the
unit by hand. Resistance should be equal in both
directions.
3.If it is felt that the unit is outside acceptable
limits, fit a new steering damperSTEERING FAULTS
Symptom:-
Excessive kickback through steering wheel - when
driven on rough terrain.
1.Is the steering damper in good working order?
See Steering Damper.
NO - Renew unit
See Repair, Steering
Damper
.
YES - Continue.
2.Is there any looseness or free play in the
steering ball joints and linkage?
YES -
See Steering Linkage Inspect.
NO - Continue.
3.Is there any looseness or worn bushes in front
suspension?
YES -
See FRONT SUSPENSION, Repair,
Radius Arm
.
NOTE: When replacing suspension bushes
ALL bushes and fixings must be replaced.
NO - Continue.
4.Is the steering exceptionally light/sensitive when
driven on good road surface?
YES - See fault symptom -Steering
excessively light/sensitive and freeplay at
steering wheel.
NO - Suspect axle swivel resistance.
5.Check the resistance of the axle swivels
See
FRONT AXLE AND FINAL DRIVE, Overhaul,
Front Stub Axle, Constant Velocity Joint and
Swivel Pin Housing
.

STEERING
5
FAULT DIAGNOSIS REV: 05/99 Symptom :-
Steering excessively light/sensitive. Excessive
freeplay at steering wheel.
1.Are steering box adjustments correct?
NO -
See Adjustment, Power Steering Box.
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is within warranty, it must be
returned to manufacturer. No attempt must be
made to introduce backlash.
YES - Suspect worn panhard rod or radius arm
bushes. Check condition of ball joints and the
lower steering column shaft universal joints for
wear
See Repair, Lower Steering Shaft and
Universal Joints
.
Symptom :-
Steering vibration, road wheel shimmy - wobble.
Vibration through the steering linkage powerful
enough to induce high frequency oscillation of the
steering wheel, is generally caused by out of balance
road wheels. However there are a number of other
possible causes of this symptom which if severe, may
be described as shimmy or wobble. Regardless of the
terminology used by the owner/driver to describe the
symptoms, the following diagnostic checks should be
carried out in the order presented.
1.Check the tyres and balance of the road wheels
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres
,See
WHEELS AND TYRES, Fault diagnosis, Fault
- Symptoms See WHEELS AND TYRES,
Repair, Wheel Balancing .
2.Check the steering hydraulic damper function
See Steering Damper.
3.Check steering column universal joints for wear
and correct alignment
See Repair, Lower
Steering Shaft and Universal Joints
.4.Check steering linkage ball joints for wear,
correct alignment and security, including steering
box and tie rod
See Steering Linkage Inspect
.
5.Check all front suspension rubbers for wear.
Check all fixing torques, including radius arm
bushes, panhard rod and anti-roll bar
See
FRONT SUSPENSION, Repair, Panhard Rod
,
See FRONT SUSPENSION, Repair, Radius
Arm
,See FRONT SUSPENSION, Repair,
Anti-Roll Bar
,See FRONT SUSPENSION,
Repair, Front Shock Absorber
.
6.Fit new radius arm bushes using NTC 6781. Fit
new nuts, bolts and washers.
7.If problem persists fit damper kit STC 288 - 90,
STC 290 - 110/130 (2 off front) and STC 289 -
90, STC 291 - 110 levelled, STC 292 - 110
unlevelled, STC 293 - 130 (2 off rear). Road test
vehicle.
8.Check the power steering box adjustments and
operation
See Overhaul, Power Steering Box.
9.Check the hub bearing end floats and determine
the condition of the hub bearings as applicable
See FRONT AXLE AND FINAL DRIVE, Repair,
Front Hub Assembly
.
10.Check the resistance and condition of the
swivels
See FRONT AXLE AND FINAL DRIVE,
Description and operation, Description
.
If problem is not diagnosed: Repeat checks
starting at 1.
11.Carry out a full steering geometry check
See
GENERAL SPECIFICATION DATA,
Information, Steering
.