1996 FORD WINDSTAR ESP

116
[IP02318(ALL)06/94]
NOTE: The compressor will not operate when the outside
temperature is less than about45ÊF (7ÊC).
% [IP02322(ALL)04/95]
Rear Climate Control System (If equipped)
[IP02332(ALL)04/95]
If your vehicle is equipped with a rear climate control system,
the rear seat occupants can select their own personal fan speed
settings.
[IP02342(ALL)05/95]
The rear seat climate control system is controlled from the main
climate control system on the instrument panel. If the rear
passenger compartment climate control knob in the front climate
control panel is set in OFF, the fan in the rear seat climate
control system will also be off. If the knob is set in any of the
fan speed positions (Medium Low, Medium High, or High), air
will be discharged from the rear seat vents at the corresponding
speed. However, when the knob is set at REAR CTRL, rear seat
passengers can control their own fan speed.
[IP02362(ALL)05/95]
7-1/2 pica art:0050048-D
Rear fan control knob
[IP02366(ALL)05/95]
The rear passenger compartment climate control panel has a Fan
Speed Knob which controls the speed (Low, Medium Low,
Medium High, or High) at which air is discharged from the
registers whenever the Rear Control Knob on the front panel
climate control panel is in REAR CTRL.
[IP02380(ALL)05/95]
Front passengers determine the temperature and location of the
airflow for rear passengers by setting the Function Selector
Knob in the front climate control panel in either a heat or A/C
mode.
File:wnips.ex
Update:Tue Mar 19 08:23:17 1996

Steering Column Controls
139
[SC09010(ALL)05/95]
NOTE: On a downhill grade, if your speed increases above
your set speed while driving inj(Overdrive) on a
downhill grade, you may want to downshift to Third
(3) gear to reduce vehicle speed. To do this, push the
Overdrive ON/OFF button on the end of the gearshift
lever. The OVERDRIVE OFF lamp will illuminate
when you press the switch.
[SC09020(ALL)05/95]
You may want to drive in 3 (Third) when driving in hilly
terrain, at high altitudes, or when pulling a trailer. This will
improve speed control performance.
[SC09030(ALL)06/94]
NOTE: When driving uphill, especially with a heavy load,
you may notice your speed decreasing even if you
have the speed control set. If the speed drops more
than 8 to 14 mph (13-23 km/h) it is normal for the
automatic speed control feature to be cancelled. You
may need to use the accelerator pedal to help your
vehicle maintain the selected speed when driving up
steep grades.
*
[SC09100(ALL)05/95]
RWARNING
Do not use the speed control in heavy traffic or on roads
that are winding, slippery, or unpaved.
[SC09200(ALL)09/93]
Accelerating With the Speed Control On
[SC09300(ALL)03/94]
If you want to speed up momentarily, or regain preset speed on
hills when the speed control is on, accelerate using the
accelerator pedal. Manually accelerating to a higher speed does
not interfere with the speed control. When you take your foot
off the accelerator, your vehicle returns to the set speed.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

150
*
[FV06901(ALL)02/95]
To erase your personal code:
*
[FV07001(ALL)02/95]1.
Enter the original permanent code.
[FV07101(ALL)04/95]2.
Press the 1/2 button within five seconds of step #1.
*
[FV07201(ALL)02/95]3.
Wait six seconds.
[FV07250(ALL)11/93]4.
The keyless entry system automatically erases your personal
code. The system will now only respond to the permanent
code.
[FV07270(ALL)10/93]
Do not set a code that presents the numbers in sequential order,
such as 1/2, 3/4, 5/6, 7/8, 9/0. Studies show that people who
idly press the buttons usually press a sequential pattern. Also,
do not select a code that uses the same button five times.
Thieves can easily figure out these types of codes.
%*
[FV07300(ALL)01/93]
Unlocking the Doors with the Keyless Entry System
[FV07401(ALL)05/95]
You must unlock the driver's door before you unlock any of the
other doors. If you let more than five seconds pass between
pressing numbers, the system shuts down and you have to
enter the code again. The system has shut down if the keypad
light is out. If the keyless entry system does not work properly,
use the key or Remote Entry transmitter(s) to lock and unlock
the doors or liftgate until the system can be serviced.
[FV07501(ALL)02/95]1.
To unlock the driver's door, enter the code. All codes have 5
numbers. After you press the fifth number, the driver's door
unlocks.
[FV07601(ALL)06/94]2.
To unlock the passenger's door, sliding door and liftgate,
press 3/4 within five seconds of step #1, or re-enter the code
to open the driver's door then press 3/4.
*
[FV07701(ALL)02/95]
Locking the doors with the keyless entry system
*
[FV07801(ALL)03/94]
Along with unlocking your doors, you can use the keyless entry
system to lock the doors.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996

198
*
[AS02600(ALL)04/95]
n
Using the ªSCAN/TUNEº button to scan radio stations
*
[AS02700(ALL)04/95]
Pressing the ªSCAN/TUNEº button once enters the scan
mode (display will indicate ªSCNº). Pushing the top
ahalf
of the ªSEEKº button will begin the scan mode up the
frequency band, stopping on each listenable station for
approximately five seconds. Pushing the bottom
bhalf of
the ªSEEKº button will begin the scan mode down the
frequency band, again stopping on each listenable station for
approximately five seconds.
*
[AS02800(ALL)04/95]
To stop the scan mode on the presently sampled station
press the ªSCAN/TUNEº button again.
*
[AS03000(ALL)01/95]
n
Setting the station MEMORY PRESET buttons
%*
[AS03100(ALL)04/95]
Your radio is equipped with 5 station memory buttons.
These buttons can be used to select up to 5 preset AM
stations and 10 FM stations (5 in FM1 and 5 in FM2). Follow
the easy steps below to set these buttons to the desired
frequencies.
*
[AS03200(ALL)04/95]1.
Select a band, then select a frequency.
*
[AS03400(ALL)04/95]2.
Press one of the memory buttons and hold the button until
the sound returns. That station is now held in memory on
that button.
*
[AS03500(ALL)04/95]3.
Follow the two steps above for each station memory preset
button you want to set.
[AS03600(ALL)04/92]
Using the Automatic Memory Load and Automatic
Memory Store features
[AS03700(ALL)10/94]
NOTE: If no stations are in memory presets, you can activate
the feature by pressing and holding the ªAUTO
PRESETº button for approximately three seconds.
Auto Memory Load sets all memory buttons in AM,
FM1 and FM2 sequentially by seeking out the first
five strong stations for the respective band and storing
them in memory buttons 1-5. (FM2 will store the
second set of strong stations from the FM band.)
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

Electronic Sound Systems
199
*
[AS03800(ALL)05/95]
With Auto Memory Store, you can continually set strong
stations into your memory buttons without losing your
existing memory presets, which is especially handy while
traveling. Your radio will automatically set your memory
buttons to the strong local stations so you don't have to
continually manually tune to existing stations.
[AS03900(ALL)10/94]
Activate Auto Memory Store by pushing the ªAUTO
PRESETº button once. Your radio will set the first five
strong stations of the band you are in (AM, FM1 or FM2)
into the memory buttons. The display will show ªAUTOº,
then run through the frequencies, stopping momentarily on
the stations being set into the memory buttons. The radio is
now in the ªAUTOº mode and this display will show
ªAUTOº each time a preset is activated.
*
[AS04000(ALL)05/95]
NOTE: If there are fewer than five strong stations in the
frequency band, the remaining unfilled buttons will
store the last strong station detected on the band.
*
[AS04100(ALL)05/95]
After all stations have been filled, the radio will begin
playing the station stored on memory button 1.
[AS04200(ALL)04/95]
To deactivate the Auto Memory Store mode and return to
the manually-set memory button stations (or those stations
set using Auto Memory Load), simply push the ªAUTO
PRESETº button. Display will show ªAUTOº then ªOFFº.
The next time Auto Memory Store is activated on that band,
the radio will store the next set of five strong stations.
*
[AS04400(ALL)04/95]
Using the ªAUDIOº button to adjust the tone balance
and speaker output
*
[AS04500(ALL)04/95]
n
Increasing or decreasing bass response
*
[AS04600(ALL)04/95]
Push the ªAUDIOº button repeatedly until the display reads
ªBASS.º Push the ª+º side of the ªVOLº button to increase
bass (more ªlowsº), and push the ª-º side to decrease bass
(less ªlowsº).
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

200
*
[AS04700(ALL)04/95]
n
Increasing or decreasing treble response
*
[AS04800(ALL)04/95]
Push the ªAUDIOº button repeatedly until the display reads
ªTREB.º Push the ª+º side of the ªVOLº button to increase
treble (more ªhighsº), and push the ª-º side to decrease
treble (less ªhighsº).
*
[AS05100(ALL)04/95]
n
Adjusting speaker balance
*
[AS05200(ALL)04/95]
Balance control allows you to adjust the sound distribution
between the right and left speakers. Push the ªAUDIOº
button repeatedly until the display reads ªBAL.º Push the
ª+º side of the ªVOLº button to shift the sound to the right
speakers, and push the ª-º side to shift the sound to the left
speakers.
*
[AS05300(ALL)04/95]
n
Adjusting speaker fader
*
[AS05400(ALL)04/95]
Fade control allows you to adjust the sound distribution
between the front and rear speakers. Push the ªAUDIOº
button repeatedly until the display reads ªFADE.º Push the
ª+º side of the ªVOLº button to shift the sound to the front
speakers, and push the ª-º side to shift the sound to the rear
speakers.
[AS05500(ALL)11/93]
NOTE: Illuminated bars in the display show relative levels of
bass and treble and positions of speaker balance and
fader functions for five seconds after adjustments are
made, then revert to volume level set.
%*
[AS05600(ALL)04/95]
Clock operation
*
[AS05700(ALL)04/95]
When in the radio mode, push the ªCLOCKº button to switch
from radio frequency to clock. Only the clock numerals will be
displayed in the clock mode Ð there is no A.M./P.M.
indication. When in the clock mode, the time will be displayed
until the button is pushed again. However, if you retune the
radio while it is in the clock mode, the new radio frequency
will be displayed for approximately ten seconds and then
change back to clock.
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

Electronic Sound Systems
203
*
[AS08400(ALL)05/95]
How to fast forward or reverse your CD player
*
[AS08500(ALL)05/95]
To quickly search for a particular point in a selection, press the
ªFFº button (to fast forward) or the ªREVº button (to reverse).
While either button is pressed, the disc goes forward or
backward at two different speeds depending on how long the
button is held down. (Pressing either button for more than
approximately three seconds will speed up the process.) Release
the button at the desired point (found by watching the elapsed
playing time in the display or by listening to the sound during
fast forward or reverse). When you have reached the beginning
of track 1, the CD player will begin playing.
*
[AS08600(ALL)04/95]
When you have reached the end of the disc by keeping the fast
forward button pressed, the display will show ªENDº and the
player will go into pause mode. Push the ªPLAY/STOPº button
to begin playing the first track of the disc, press the ªREVº
button to back up from the end of the disc, or use the ªSEEKº
function to locate a desired track.
*
[AS08610(ALL)04/95]
Using the ªSEEKº feature
[AS08620(ALL)10/94]
Press the top (
a) of the ªSEEKº button once to repeat the
current playing selection. Press the bottom (
b) of the ªSEEKº
button to advance to the next selection.
[AS08630(ALL)10/94]
Pressing and holding the top (
a) or bottom (
b) of the ªSEEKº
button will scroll backward and forward respectively through
the tracks.
*
[AS08700(ALL)04/95]
Using the ªSCANº function
*
[AS08800(ALL)04/95]
Press the ªSCAN/TUNEº button to enter the scan mode. Once
in the scan mode, press the top (
a) or bottom (
b) half of the
ªSEEKº button to scan forward or reverse, respectively. The CD
player will begin scanning the disc, stopping on each listenable
track for approximately eight seconds. This continues until you
press the ªSCAN/TUNEº button a second time. While in the
scan mode, the display shows the current sampled track
number.
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

Electronic Sound Systems
211
*
[AS10240(ALL)04/95]
n
Using the Automatic Memory Load feature
[AS10250(ALL)10/94]
NOTE: If no stations are in memory presets, you can activate
the feature by pressing and holding the ªAUTO
PRESETº button for approximately three seconds.
Auto Memory Load sets all memory buttons in AM,
FM1 and FM2 sequentially by seeking out the first
five strong stations for the respective band and storing
them in memory buttons 1-5. (FM2 will store the
second set of strong stations from the FM band.)
*
[AS10260(ALL)05/95]
With Auto Memory Store, you can continually set strong
stations into your memory buttons without losing your
existing memory presets, which is especially handy while
traveling. Your radio will automatically set your memory
buttons to the strong local stations so you don't have to
continually manually tune to existing stations.
[AS10270(ALL)07/92]
Activate Auto Memory Store by pushing the ªAUTO
PRESETº button once. Your radio will set the first five
strong stations of the band you are in (AM, FM1 or FM2)
into the memory buttons. The display will show ªAUTOº,
then run through the frequencies, stopping momentarily on
the stations being set into the memory buttons. The radio is
now in the ªAUTOº mode for the selected band and this
display will show ªAUTOº each time a preset is activated.
*
[AS10280(ALL)05/95]
NOTE: If there are fewer than five strong stations in the
frequency band, the remaining unfilled buttons will
store the last strong station detected on the band.
*
[AS10290(ALL)05/95]
After all stations have been filled, the radio will begin
playing the station stored on memory button 1.
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996