1996 FORD RANGER wheel torque

Introductory Information
5
%*
[IN06000(ALL)01/95]
Breaking Your Vehicle In
*
[IN06100(ALL)03/95]
Your new vehicle goes through an adjustment or break-in
period during the first 1,000 miles (1,600 km) that you drive it.
During the break-in period, you need to pay careful attention to
how you drive your vehicle.
%*
[IN06300(ALL)01/95]
n
Avoid sudden stops.Because your vehicle has new brake
linings, you should take these steps:
*
[IN06400(ALL)01/95]
Ð Watch traffic carefully so that you can anticipate when to
stop.
*
[IN06500(ALL)01/95]
Ð Begin braking well in advance.
*
[IN06600(ALL)01/95]
Ð Apply the brakes gradually.
*
[IN06700(ALL)01/95]
The break-in period for new brake linings lasts for 100 miles
(160 km) of city driving or 1,000 miles (1,600 km) of
highway driving.
*
[IN06750(ALL)12/93]
n
Wheel lug nuts must be retightened to proper torque
specifications at 500 miles/800 km of new vehicle operation.
Proper torque specifications are provided in this guide. Also
retighten to proper torque specification at 500 miles/800 km
after any wheel change or any other time the wheel lug nuts
have been loosened.
%*
[IN06800(ALL)01/95]
n
Use only the type of engine oil that Ford recommends.See
Engine oil recommendationsin the Index. Do not use special
ªbreak-inº oils.
*
[IN07000(ALL)03/95]
Some vehicles are equipped with a Powertrain Control Module
that limits engine speeds with a cut-out mode to promote
durability.
File:02uninr.ex
Update:Wed May 1 13:42:39 1996

Roadside Emergencies
233
*
[RE23800(ALL)06/93]
Retighten the wheel lug nuts to the specified torque at 500 miles
(800 km) of new vehicle operation and at intervals specified in
theMaintenance Schedule and Recordbooklet.
*
[RE24200(ALL)10/89]
Also retighten to the specified torque at 500 miles (800 km) of
operation after any wheel change or any time the lug nuts are
loosened.
*
[RE24301(ALL)05/95]
RWARNING
Failure to retighten wheel lug nuts at mileages specified
could allow wheels to come off while the vehicle is in
motion.
[RE24360(R )04/94]
eight pica
chart:0020316-B[RE24400(ALL)10/94]
The Fuel Pump Shut-off Switch
*
[RE24500(ALL)07/95]
If the engine cranks but does not start or if you have had a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device that stops the fuel
pump when your vehicle has been involved in a substantial jolt.
*
[RE24600(ALL)07/95]
For information on how to check and reset the fuel pump
shut-off switch, seeFuel pump shut-off switchin the Index.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996

236
[RE27600(ALL)12/91]
Recreational Towing Ð All wheels on the ground
[RE27700(ALL)05/91]
Towing your vehicle can be successfully performed by following
the appropriate guidelines for the type of powertrain on the
vehicle to be towed. The following guidelines, by powertrain
combination, are designed to ensure that the transmission is not
damaged due to insufficient lubrication.
[RE27800(ALL)12/91]
4x2ÐAutomatictransmission
*
[RE27900(ALL)03/95]
n
Release the parking brake.
[RE28000(ALL)01/95]
n
Place transmission gearshift in N (neutral).
[RE28100(ALL)10/94]
n
Maximum speed is 35 mph (56 km/h).
[RE28200(ALL)10/94]
n
Maximum distance is 50 miles (80 km).
[RE28300(ALL)06/94]
If a distance of 50 miles (80 km) or speed of 35 mph (56 km/h)
will be exceeded, youmust:
[RE28400(ALL)05/91]
n
Disconnect the driveshaft at the rear differential and properly
support it under the vehicle.
[RE28500(ALL)01/95]
n
Mark the driveshaft and axle flanges to ensure proper
position when reconnecting the driveshaft. Refer to service
manual for proper driveshaft fastener torque specification.
(See theAccessorieschapter for information on ordering
service manuals.)
[RE28600(ALL)05/95]
RWARNING
When disconnecting/installing the driveshaft, the parking
brake must be set and the wheels blocked to ensure the
vehicle does not roll.
[RE28700(ALL)06/94]
n
Maximum speed is 55 mph (88 km/h), unlimited distance.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996

238
[RE30300(ALL)06/94]
n
Mark the driveshaft and transfer case/axle flanges to ensure
proper position when installing the driveshaft. Refer to
service manual for proper driveshaft torque specification.
[RE30400(ALL)05/95]
RWARNING
When disconnecting/installing the driveshaft, the parking
brake must be set and the wheels blocked to ensure the
vehicle does not roll.
[RE30500(ALL)06/94]
n
Maximum speed is 55 mph (88 km/h), unlimited distance.
[RE30525(ALL)10/92]
For manual transmissions:
[RE30550(ALL)06/94]
n
Maximum speed is 55 mph (88 km/h), unlimited distance.
[RE30600(ALL)10/94]
Limited vehicle operation, such as driving the vehicle while at a
campsite, can be accomplished with the rear driveshaftremoved
by using the front drive to propel the vehicle. To operate the
vehicle in this condition, youmustfollow the following
guidelines:
[RE30700(ALL)10/94]
n
Place the transfer case in 4WD by rotating 4WD switch to
4WD HIGH.
[RE30800(ALL)10/94]
n
Drive the vehicleonlyon good surface roads to avoid
excessive loads on the front-wheel drive system.
[RE30900(ALL)10/94]
n
Maximum speed is 35 mph (56 km/h).
[RE31000(ALL)10/94]
n
Maximum distance is 50 miles (80 km).
[RE31100(ALL)10/94]
n
Avoid quick acceleration and steep grades.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996

290
[SV26800(R )04/94]
17-1/2 pica
art:0021191-A
Tire rotation pattern
*
[SV26900(ALL)10/89]
After each rotation, adjust individual tire pressure as specified
on the Safety Compliance Certification Label. Tighten wheel lug
nuts to the required torque specification and retighten again
after 500 miles (800 km).
*
[SV27000(ALL)08/95]
If your vehicle has aluminum wheels, you may demount the full
size, non-temporary spare tire (if so equipped) and remount on
an aluminum wheel to rotate the spare tire into your vehicle's
rotation pattern. Rebalance the wheel.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996