1996 FORD RANGER ECO mode

Electronic Sound Systems
141
*
[AS29905(ALL)04/95]
Operating the CD Compression feature
[AS29910(ALL)04/94]
Because of the wide dynamic range of Ford's 6-CD Changer
System, soft passages may be difficult to hear under certain
driving conditions while maintaining a reasonable volume level
in the louder passages. The compression feature will bring these
soft and loud passages closer together for a more consistent
listening level.
*
[AS29915(ALL)01/95]
To turn the compression on, press the ªCOMPRESSº/#5 button.
When the compression feature is activated, the display will
indicate ªCº.
*
[AS29916(ALL)02/95]
Operating the Shuffle feature
*
[AS29917(ALL)01/95]
While in the CD mode, pressing the ªSHUFFLEº/#6 button will
randomly select a track from the disc currently being played.
The display will indicate ªSHFº followed by the disc and track
number (dd-tt).
*
[AS29918(ALL)01/95]
The CD Changer will continue to randomly select tracks for
play until the shuffle feature is turned off by pressing the
ªSHUFFLEº button a second time.
*
[AS29919(ALL)02/95]
HowtostopCDplay
*
[AS29920(ALL)01/95]
While in the CD mode, press the ªAM/FMº button to stop CD
play and resume radio play. Also, loading a cassette into the
cassette deck will stop CD play and begin cassette play.
*
[AS29935(ALL)02/95]
CD Error Messages
*
[AS29936(ALL)01/95]
Your system is equipped to diagnose certain problems you may
experience. The error codes are:
*
[AS29937(ALL)01/95]
ÐCD E1Ð Mechanism error.
*
[AS29938(ALL)01/95]
ÐCD E2Ð Focus error.
*
[AS29939(ALL)01/95]
ÐBAD CDÐ Disc unreadable.
File:09unasr.ex
Update:Wed May 1 13:49:43 1996

Electronic Sound Systems
147
*
[AS30010(ALL)09/95]
n
Using the ºTUNEª function
*
[AS30015(ALL)03/95]
You can change the frequency up or down one increment at
a time by pressing and releasing either the left (
b) or right
(
a) side of the ºTUNEª button.
*
[AS30020(ALL)10/95]
Manual tuning adjusts your radio to any allowable broadcast
frequency, whether or not a station is present on that
frequency. (SeeAll About Radio Frequenciesin this section.)
*
[AS30025(ALL)10/95]
n
Using the ºSEEKª function
*
[AS30030(ALL)09/95]
This feature on your radio allows you to automatically select
listenable stations up or down the frequency band. Press the
right (
a) side of the ºSEEKª button to select the next
listenable station up the frequency band. Press the left (
b)
side of the button to select the next listenable station down
the frequency band. By holding the button down, listenable
stations can be passed over to reach the desired station.
*
[AS30035(ALL)01/95]
n
Using the ºSCANª function
*
[AS30040(ALL)04/95]
Pressing the ºSCANª button will begin the scan mode up
the frequency band, stopping on each listenable station for
approximately five seconds.
*
[AS30045(ALL)02/95]
To stop the scan mode on the presently sampled station,
press the ºSCANª button again.
*
[AS30050(ALL)10/95]
n
Setting the Station Memory Preset buttons
*
[AS30055(ALL)10/95]
Your radio is equipped with 6 station memory buttons.
These buttons can be used to select up to 6 preset AM
stations and 12 FM stations (6 in FM1 and 6 in FM2).
File:09unasr.ex
Update:Wed May 1 13:49:43 1996

150
*
[AS30200(R )08/95]
n
Using the ºSEEKª function with your cassette tape player
*
[AS30205(R )08/95]
While in the tape mode, push the right (
a) side of the
ºSEEKª button to seek forward to the next selection on the
tape. Push the left (
b) side to seek the previous tape
selection.
*
[AS30210(R )08/95]
n
Using the ºSCANª function with your cassette tape player
*
[AS30215(R )01/95]
Press the ºSCANª button to begin the forward scan mode on
the tape currently playing, stopping on each tape selection
for approximately an eight-second sampling (display
indicates ºSCª).
*
[AS30220(R )01/95]
To stop the scan mode on the presently sampled tape
selection, press ºSCANª a second time.
*
[AS30225(R )08/95]
n
How to change the side of the tape being played
*
[AS30230(R )01/95]
The alternate side of the tape can be selected by pressing the
ºSIDE 1-2ª button.
*
[AS30235(R )08/95]
How to eject the tape
*
[AS30240(R )01/95]
To stop the tape and eject the cassette, press the ºEJª button.
The radio will resume playing if the radio power is on. The
tape cartridge can be ejected with radio power (and/or ignition)
on or off.
[AS30245(R )06/95]
HowtoswitchfromtapetoAM/FMmode
*
[AS30247(R )01/95]
Press the ºAM/FMª button to stop the tape player and resume
radio play.
*
[AS30250(R )08/95]
Using the DolbyHB noise reduction feature
*
[AS30255(R )08/95]
NOTE: Noise reduction system manufactured under license
from Dolby Labs Licensing Corporation. ºDolbyª and
double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
File:09unasr.ex
Update:Wed May 1 13:49:43 1996

Electronic Sound Systems
151
*
[AS30260(R )04/95]
Push thekbutton to activate Dolby B Noise Reduction. Push
again to deactivate.
*
[AS30345(R )08/95]
Tips on Caring for the Cassette Player and Tapes
*
[AS30350(R )08/95]
In order to keep your cassette tape player performing the way it
was meant to, read and follow these simple precautions:
*
[AS30355(R )08/95]
n
Using a Ford Cassette Cleaning Cartridge to clean the tape
player head after 10-12 hours of play will help maintain the
best playback sound and proper tape operation.
*
[AS30360(R )08/95]
n
Only cassettes that are 90 minutes long or less should be
used. Tapes longer than 90 minutes are thinner and subject
to breakage or may jam the tape player mechanism.
*
[AS30365(R )08/95]
n
Protect cassettes from exposure to direct sunlight, high
humidity and extreme heat or cold. If they are exposed to
extreme conditions, allow them to reach a moderate
temperature before playing.
*
[AS30370(R )08/95]
n
If a tape is loose inside the cassette, tighten it before playing
by putting your finger or a pencil into one of the holes and
turning the hub until the tape is tight.
*
[AS30375(R )08/95]
n
Loose labels on cassette tapes can become lodged in the
mechanism. Remove any loose label material before inserting
cassette.
*
[AS30380(R )08/95]
n
Do not leave a tape in the cassette tape player. High heat in
the vehicle can cause the cassette to warp.
%*
[AS30401(ALL)08/95]
Clock Operation
*
[AS30411(ALL)08/95]
How to view the clock mode
[AS30421(ALL)09/94]
Press the ºCLKª button to display time. The time will continue
to be displayed until a radio or tape function is chosen. After
approximately 10 seconds, the time will again appear in the
display. To display radio or tape information only, press the
ºCLKª button a second time.
File:09unasr.ex
Update:Wed May 1 13:49:43 1996

Driving Your Ranger
159
[DR09850(ALL)01/95]
quarter page
art:0021255-A
Transmission control switch (located on the end of the gearshift lever)
*
[DR09900(ALL)05/95]
To return the transmission to the normal
jOverdrive
operation, press the transmission control switch again. The
Transmission Control Indicator Light will not be illuminated
when Overdrive operation resumes. This switch may be used to
select O/D ON or O/D OFF any time the vehicle is being
driven.
*
[DR09950(ALL)05/94]
When starting your vehicle, the overdrive system will
automatically be in the normal overdrive mode.
*
[DR10100(ALL)01/95]
When to use 2 (Second)
*
[DR10200(ALL)01/95]
Use 2 (Second) to start-up on slippery roads or to provide
additional engine braking on downgrades. This position
provides 2 (Second) gear operation only.
*
[DR10300(ALL)01/95]
When to use 1 (Low)
*
[DR10400(ALL)04/95]
Use 1 (Low) to provide maximum engine braking on steep
downgrades. Upshifts from 1 (Low) can be made by manually
shifting to 2 (Second) or
j(Overdrive). Selection of 1 (Low)
gear provides only low gear operation from start-up. Selection
of 1 (Low) while at higher speeds provides a shift to second
gear, and a shift to first gear will occur after the vehicle
decelerates to the proper speed.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
171
*
[DR17500(R )05/95]
With the transfer case in N (Neutral), the vehicle is free to move
with either the automatic transmission in P (Park) or with the
manual transmission in any driving gear.
*
[DR17510(R )05/95]
RWARNING
Do not leave the vehicle unattended with the transfer
case in the N (Neutral) position. Always set the parking
brake fully and turn off the ignition when leaving the
vehicle.
*
[DR17540(R )01/95]
To shift from N (Neutral) to either 4H or 4L, stop the vehicle
and engage the parking brake. Place the automatic transmission
into N (Neutral) or depress the clutch on manual transmission
vehicles. Push the transfer case shift lever to the desired
position. If it is difficult to shift into either 4H or 4L, it may be
necessary to let the vehicle roll slightly and/or turn off the
engine (particularly on vehicles equipped with automatic
transmissions).
[DR17570(R )01/95]
4WD Systems Ð Select Drive Electric Shift
[DR17601(R )01/95]
The select drive electric shift system functions in three modes.
In two-wheel drive mode, power is delivered only to the rear
axle at normal road speed. The 4x4 HIGH position provides
four-wheel drive with power delivered to the front and rear
axles for increased traction. The 4x4 LOW position provides
four-wheel drive with power delivered to the front and rear
axles when above average power is required at reduced speeds.
[DR17630(R )01/95]
Four-wheel drive operation (4x4 HIGH or 4x4 LOW) on dry
pavement is not recommended. Operating the vehicle in
four-wheel drive on dry pavement will increase noise, vibration,
tire wear, decrease fuel economy, and make four-wheel drive
disengagement difficult for the transfer case.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

174
[DR18201(R )06/94]
During axle break-in or operation in extremely cold
temperatures, the automatic locking hubs may not release
completely. It may be necessary to drive the vehicle for 10 to 15
minutes before repeating the release procedure.
[DR18240(R )08/94]
To shift from 4x4 HIGH or 2WD to 4x4 LOW:
[DR18295(R )01/95]
Stop the vehicle, depress the brake and place the automatic
transmission in N (Neutral) or depress the clutch on vehicles
with a manual transmission. Rotate the 4WD switch on the
instrument panel to 4x4 LOW. Both the 4WD and 4WD LOW
lights are now lit.
[DR18350(R )08/94]
To shift from 4x4 LOW to 4x4 HIGH or 2WD:
[DR18380(R )01/95]
Stop the vehicle, depress the brake and place the automatic
transmission into N (Neutral) or depress the clutch on vehicles
with a manual transmission. Rotate the 4WD switch on the
instrument panel to 4x4 HIGH or 2WD.
[DR18500(ALL)03/95]
It is not recommended to operate the vehicle in the 4WD modes
with a temporary spare. If 4WD operation is necessary, do not
operate at speeds above 10 mph or for distances above 50 miles.
Extended operation in 4WD with a temporary spare may result
in damage to drivetrain components.
%*
[DR19200(ALL)01/89]
Driving Off Road with 4-Wheel Drive
*
[DR19300(ALL)11/89]
Most vehicles with four-wheel drive are especially equipped for
driving on sand, snow, mud, or rough terrain and have
operating characteristics that are somewhat different from
conventional vehicles, both off and on the road. The driving tips
below will help you learn to use four-wheel drive.
[DR19500(R )08/94]
n
Do not use four-wheel drive on dry, hard-surfaced roads,
especially with a temporary spare tire in use.
*
[DR19600(ALL)11/89]
n
Special maintenance procedures are necessary after operating
with drive components in water.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
181
%*
[DR23000(ALL)12/89]
If Brakes Do Not Grip Well or Pedal is ªLowº
%*
[DR23200(R )07/95]
If brakes do not grip well, it may indicate the rear drum brakes
need adjustment. To do this, drive the vehicle in reverse at
5 mph (8 km/h) on level, dry pavement. Stop the vehicle by
firmly applying the brakes. Repeat this procedure four or five
times.
*
[DR23250(ALL)11/89]
If during normal operation the brake pedal seems ªlowº, it may
indicate the need for a brake system inspection and/or service.
You should have your brakes checked as soon as possible.
%*
[DR23300(ALL)10/95]
Occasional brake squeal during light to moderate stops does not
affect the function of the brake system and is normal. However,
if the squeal becomes louder or more frequent, have your
brakes inspected by your dealer or a qualified service technician.
*
[DR23400(ALL)11/89]
RWARNING
Modifications to the suspension spring rates and/or
vehicle ride height may adversely affect vehicle stopping
ability.
*
[DR23500(ALL)07/92]
If Brakes Pull
*
[DR23600(ALL)05/95]
n
Check tire pressure.
*
[DR23700(R )07/95]
n
Perform the self-adjustment procedure described underIf
Brakes Do Not Grip Well or Pedal is ªLow.º
*
[DR23800(ALL)05/95]
If pull occurs during the first 500 miles (800 km), make 10
moderately fast stops from 40 mph (65 km/h) and then
perform the self-adjustment procedure above. It may be
necessary to repeat this operation to properly seat new brake
linings and pads.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996