1996 FORD MUSTANG ECU

138 [FV42300(M )03/93]7. The two pins under the forward edge of the
top should seat themselves in the matching
holes in the header.
[FV42400(M )06/93]
8. To fasten both clamps securely, push the
clamp handles into the header on the top
until they are flush with the header. Pulling
down on the header at the center grip while
closing the latches may assist in fastening
the clamps.
[FV42410(M )03/93]
9. Raise the front and rear side windows.
% [FV42412(M )03/95]
Convertible Top and Padded Molding Care
[FV42414(M )03/95]
To avoid damage to the vinyl top and moldings,
use only an approved Ford cleaner, or
equivalent. Do not use stiff bristle brushes or
abrasive material or cleaners.
[FV42416(M )03/95]
Hot waxes applied by automatic car washes can
affect the cleanability of vinyl material.
[FV42418(M )03/95]
NOTE: Using high water pressure or wand
type car washes against the convertible
top and windows may cause water
leaks and possible seal damage.
File:08rcfvm.ex
Update:Wed Mar 27 09:32:34 1996

149
[AS28650(M )03/95]
Ford Mini Disc Player
[AS28700(M )05/94]
The Ford Mini Disc Player operates when the
Audio System is on and a disc is inserted(label
side up). (Be sure to read and follow all of the
care and cleaning instructions underHow To
Take Care of Your Mini Disc Player and Discsin
this section.)
[AS28800(M )05/94]
The digital display on your Mini Disc player
shows the track (selection) number and the disc
title.
[AS28900(M )05/94]
Once a disc is inserted, operation of the Mini
Disc player will override that of the cassette
player or radio.
[AS29000(M )05/94]
Using the Controls on Your New Mini
Disc Player
[AS29100(M )09/95]
NOTE: The volume, bass, treble, balance and
fader controls on the radio are also
used with the Mini Disc player. Refer
toUsing the Controls on Your New
Radioin this section for operating
instructions on these controls.
*
[AS29200(M )10/95]
How to insert a disc and begin play
[AS29300(M )05/94]
Insert one disc,label side upinto the disc
opening. Arrow on top of disc must point
inward. When inserted, the disc automatically
loads into the unit and play starts at the
beginning of the first track (selection).
*
[AS29400(M )10/95]
When the disc reaches the end, the disc player
automatically returns to the beginning of the
disc and resumes playing.
*
[AS29500(M )09/95]
NOTE: Once a disc is inserted, the disc
opening is secured to prevent the
accidental insertion of a second disc.
File:09rcasm.ex
Update:Wed Mar 27 09:33:20 1996

156
*
[AS38330(M )10/95]
NOTE: Once a disc is inserted, the disc
opening is secured to prevent the
accidental insertion of a second disc.
[AS38340(M )03/95]
NOTE: The CD player has heat protection
circuitry to protect the laser diode. If
the temperature of the player reaches
167ÊF (75ÊC), theheat detection circuit
will shut off the player and ªHOTº
will appear in the display. When the
temperature is within normal operating
range, the ªHOTº indication will turn
off and the CD player will again be
operational.
*
[AS38400(M )10/95]
How to stop and restart the CD player
[AS38450(M )03/95]
When a disc is loaded, the unit automatically
enters the play mode and the play indicator (
a)
illuminates. To stop temporarily, press the
ªPLAY/STOPº button. The stop indicator (
X)in
the display illuminates and operation returns to
the radio or tape mode. To resume CD play,
press this button once again or press any other
function button (except ªEJECTº or
ªCOMPRESSº buttons).
*
[AS38475(M )10/95]
NOTE: If the ignition key is turned OFF
during play and then is set to the ON
or ACCESSORY position, the CD
player will resume playing in the mode
it was in when ignition was turned off.
*
[AS38500(M )03/95]
How to locate a selection on your CD
player using Automatic Music Search (AMS)
*
[AS38510(M )06/95]
An ªAMSº (Automatic Music Search) control on
your CD player allows you to quickly find a
particular selection on the disc. Press the left
fside of the ªAMSº control to locate a
previous selection or the right
eside of the
ªAMSº control to locate a later selection.
File:09rcasm.ex
Update:Wed Mar 27 09:33:20 1996

179 % [DR01200(M )03/93]
half page art:0010306-D
The positions of the console-mounted gearshift
*
[DR01500( ALL)11/94]
Once the gearshift is secure in the desired
position, release the brake pedal and use the
accelerator as necessary.
%*
[DR01700( ALL)01/95]
R (Reverse)
*
[DR01800( ALL)08/95]
With the gearshift in the R (Reverse) position,
the vehicle will move backward. You should
always come to a complete stop before shifting
into or out of R (Reverse).
*
[DR01830( ALL)01/95]
N (Neutral)
[DR01860( ALL)10/95]
As in P (Park), there is no power transferred
through the transmission. However, the final
drive is not locked so the wheels are free to
rotate. The vehicle may be started in the N
position, but the ignition key cannot be
removed.
File:10rcdrm.ex
Update:Wed Mar 27 09:33:56 1996

181
*
[DR02200( ALL)01/95]
However, Overdrive also shifts into a fourth
gear Ðan overdrive gear Ð when your vehicle
cruises at an appropriate consistent speed for
any length of time. This fourth gear will increase
your fuel economy when you travel at cruising
speeds.
[DR02500(MBC )05/95]
When to use D (Overdrive) Ð with
transmission control switch activated (O/D
OFF light illuminated)
*
[DR02600(MBC )01/95]
Overdrive may not be appropriate for certain
terrain. If the transmission shifts back and forth
between Third and Fourth gears while you are
driving on hilly roads or if your vehicle does
not have adequate power for climbing hills,
depress the TCS.
[DR02606(M )06/93]
You can depress the TCS marked ªODº at any
speed.
*
[DR02610( ALL)01/95]
When to use 2 (Second)
*
[DR02620( ALL)01/95]
Use 2 (Second) for start-up on slippery roads or
to give you more engine braking to slow your
vehicle on downgrades.
*
[DR02700( ALL)01/95]
When to use 1 (Low)
*
[DR02800( ALL)03/95]
Use 1 (Low) when driving down steep grades. It
gives more engine braking to slow your vehicle
than 2 (Second) on the downgrades. You can
upshift from 1 (Low) to 2 (Second) or from 1
(Low) to Overdrive at any speed.
*
[DR03000( ALL)01/95]
P (Park)
*
[DR03100( ALL)01/95]
Always come to a complete stop before you shift
into P (Park). Make sure that the gearshift is
securely latched in P (Park). This locks the
transmission and prevents the rear wheels from
rotating.
File:10rcdrm.ex
Update:Wed Mar 27 09:33:56 1996

182
*
[DR03200( ALL)06/95]
RWARNING
Always set the parking brake fully and
make sure the gearshift is securely latched
in P (Park).
*
[DR03225( ALL)06/95]
RWARNING
Never leave your vehicle unattended
while it is running.
*
[DR03400(MBC )01/95]
You can tell a console-mounted gearshift is
securely latched in P (Park) if the lever is
adjacent to the P (Park) and you cannot move it
without pushing in the thumb button.
%
*
[DR06100(M )03/95]
Driving with a Manual
Transmission
%*
[DR06200(M )03/95]
Using the Clutch
[DR06300(M )03/95]
After starting the engine with the clutch pedal
pushed to the floor, allow it to idle for a few
seconds. Then, hold your right foot on the brake
pedal. Release the hand brake. Move the
gearshift into 1 (First) or R (Reverse) gear.
[DR06400(M )03/95]
To move the vehicle, pull your right foot off the
brake pedal and then slowly release the clutch
pedal. (You may need to press down slowly on
the accelerator at the same time that you release
the clutch pedal.)
*
[DR06500(M )03/95]
Do not drive with your foot resting on the
clutch pedal and do not use the clutch to hold
your vehicle at a standstill while waiting on a
hill. These actions will seriously reduce clutch
life.
*
[DR06600(M )03/95]
Driving with your foot resting on the clutch may
cause the vehicle to jerk sharply when pressing
or removing your other foot from the
accelerator.
File:10rcdrm.ex
Update:Wed Mar 27 09:33:56 1996

189
*
[DR13700(M )03/95]
RWARNING
When parking, do not use the gearshift in
place of the parking brake. Turn the key
to LOCK whenever you leave your
vehicle. Always set the parking brake
fully and make sure that the gearshift is
securely latched in P (Park) (automatic
transmission) or in 1 (First) (manual
transmission). Never leave your vehicle
unattended while it is running. If you do
not take these precautions, your vehicle
may move unexpectedly and injure
someone.
[DR13900(M )10/95]
To release the parking brake, pull the handle
upward, push in the button, then lower the
handle. The Brake System warning light will
glow if the parking brake is not fully released
when the engine is running.
*
[DR14200( ALL)03/95]
Always check the Brake Warning Light each
time you start your engine. Driving with the
parking brake on will cause the brakes to wear
out quickly and will reduce the fuel economy.
*
[DR14300( ALL)01/93]
RWARNING
If the parking brake is fully released, but
the Brake System light remains on, have
the brakes checked immediately. They
may not be working properly.
[DR14400( ALL)07/93]
The parking brake system is designed for static
parking only and is not designed to stop a
moving vehicle, but you can use the parking
brake to stop your vehicle in an emergency if
the normal brakes fail. However, since the
parking brake applies only the rear brakes, the
stopping distance will increase greatly and the
handling of your vehicle will be adversely
affected.
File:10rcdrm.ex
Update:Wed Mar 27 09:33:56 1996

211
*
[RE08980( ALL)01/95]
6. Remove the jack and fully tighten the lug
nuts in the order shown in the following
illustration. As soon as possible, have your
dealer or a qualified service technician check
the lug nuts for proper torque specifications.
% [RE09100( ALL)03/93]
quarter page art:0010350-A
The lug nuts on the wheel
*
[RE09400( ALL)01/95]
7. Place any wheel covers and ornaments in the
trunk.
*
[RE09500( ALL)03/95]
8. Put the tire, jack, and wrench away. Make
sure the jack is securely fastened so it does
not rattle when you drive.
*
[RE09600( ALL)06/95]
9. Unblock the wheels.
% [RE10600(MBC )12/94]
Aluminum Road Wheel Ornaments
(If equipped)
[RE10700(MBC )03/93]
To remove the ornament, stick the tapered end
of the jack handle between the ornament and
wheel and pry off the ornament.
[RE10800(MBC )03/93]
To replace the ornament, stick one side of the
ornament into the center of the wheel and strike
the other side with the palm of your hand.
[RE11838(M GV)03/93]
Remove the wheelcover from the wheel using
the flanged end of the wheel nut wrench by
inserting the handle and then prying against the
inner wheelcover flange.
[RE11842(M GV)10/95]
Install the wheelcover on the wheel with the
valve stem in the wheel matching the hole in the
wheelcover. Push by hand on the outside edges
File:12rcrem.ex
Update:Wed Mar 27 09:34:49 1996