1996 FORD MUSTANG lock

35 [SR31400(M )08/93]
5. Allow the belt to retract. A clicking sound
will be heard as the belt retracts. This
indicates the retractor is in the automatic
locking mode, Figure 4.
[SR31405(M )08/93]
half page art:0011236-A
Allowing belt to retract
File:03rcsrm.ex
Update:Wed Mar 27 09:23:48 1996

38 [SR31700(M )08/93]8. Double check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor, if you cannot, the
belt is in the automatic locking mode,
Figure 7.
[SR31705(M )08/93]
half page art:0011237-A
Checking the retractor
[SR31800(M )12/93]
9. Check to make sure that the child seat or
infant carrier is properly secured prior to
each use. If the lap belt is not locked, repeat
steps 4 through 8.
*
[SR31850(M )05/95]
NOTE: To remove the retractor from automatic
lock mode, allow seat belt to retract
fully to its stowed position and the
retractor will automatically switch back
to the vehicle sensitive locking mode
for normal adult usage.
File:03rcsrm.ex
Update:Wed Mar 27 09:23:48 1996

39 % [SR31855(M )12/93]
Installing Safety Seats in the Front Seat
(Coupe only) and Rear Seating Positions
(Coupe and Convertible)
[SR31861( ALL)03/95]
For seating positions equipped with a dual
locking mode retractor, use the following
procedure.
*
[SR31865( ALL)06/95]
If you choose to install a child safety seat or
infant carrier in the front seating positions, move
vehicle seat as far back as possible.
*
[SR31870( ALL)06/95]
1. Position the child seat in the center of the
passenger seat.
*
[SR31875( ALL)09/95]
2. Pull down on shoulder belt, then grasp
shoulder belt and lap belt together. See
Figure 1.
*
[SR31880( ALL)09/95]
half page art:0011238-B
Pulling out belt webbing
File:03rcsrm.ex
Update:Wed Mar 27 09:23:48 1996

41
*
[SR31895( ALL)06/95]
half page art:0011240-B
Buckling the belt
*
[SR31900( ALL)08/95]
5. Grasp the shoulder portion of the belt and
pull downward until all of the belt is
extracted and a click is heard. At this time,
the retractor is in the automatic locking
mode (child seat restraint mode). See
Figure 4.
*
[SR31902( ALL)09/95]
NOTE: The dual-locking mode retractor must
be in the automatic locking mode to
properly restrain a child.
File:03rcsrm.ex
Update:Wed Mar 27 09:23:48 1996

42
*
[SR31905( ALL)06/95]
half page art:0011241-A
Setting the retractor to automatic locking mode
*
[SR31910( ALL)08/95]
6. Allow the belt to retract. Pull up on the
shoulder webbing. A clicking sound will be
heard as the belt retracts. This indicates the
retractor is in the automatic locking mode.
Push down on the child seat while you pull
up on the belt to remove any slack in the
belt. See Figures 5 and 6.
File:03rcsrm.ex
Update:Wed Mar 27 09:23:48 1996

45
*
[SR31935( ALL)08/95]
8. Double check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor. If you cannot, the
belt is in the automatic locking mode. See
Figure 8.
*
[SR31940( ALL)06/95]
half page art:0011245-B
Checking the retractor
*
[SR31945( ALL)06/95]
9. Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 4
through 7.
*
[SR31950(M )06/95]
To remove the retractor from automatic lock
mode, allow webbing to retract fully to its
stowed position and the retractor will
automatically switch back to the vehicle sensitive
locking mode for normal adult usage.
File:03rcsrm.ex
Update:Wed Mar 27 09:23:48 1996

49
Starting Your Mustang
*
[ST03400( ALL)03/95]
Ignition
%*
[ST03500( ALL)01/95]
Understanding the Positions of the Ignition
[ST03750( ALL)12/94]
quarter page art:0010035-B
The positions of the key in the ignition
% [ST03800(M )03/95]
ACCESSORY allows some of your vehicle's
electrical accessories such as the radio and the
windshield wipers to operate while the engine is
not running. You must push the key release
button to turn to the ACCESSORY position if
your vehicle has a manual transmission.
% [ST04001( ALL)12/94]
LOCK locks the steering wheel. It also locks the
automatic transmission gearshift lever.
*
[ST04101( ALL)01/95]
LOCK is the only position that allows you to
remove the key. The LOCK feature helps to
protect your vehicle from theft.
*
[ST04200( ALL)03/95]
OFF allows you to shut off the engine and all
accessories without locking the steering wheel or
the automatic transmission gearshift lever.
File:04rcstm.ex
Update:Wed Mar 27 09:28:42 1996

50
*
[ST04300( ALL)05/95]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[ST04400( ALL)03/95]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
%*
[ST04900( ALL)02/95]
Removing the Key From the Ignition
[ST05700(M )03/95]
1. Put the gearshift in P (Park) (automatic
transmission) or 1 (First) (manual
transmission).
*
[ST05800( ALL)01/95]
2. Set the parking brake fully.
[ST06000(M )03/95]
3. Turn the ignition to the OFF (manual
transmission) or LOCK (automatic
transmission).
[ST06100(M )03/95]
4. Push in the key release button until it
catches and stays in (manual transmission
only).
[ST06250(M )03/95]
quarter page art:0010619-B
Key release button (manual transmission only)
[ST06500(M )03/95]
5. Turn the key to LOCK (manual
transmission).
*
[ST06600(M )05/95]
6. Remove the key.
File:04rcstm.ex
Update:Wed Mar 27 09:28:42 1996