1996 FORD EXPLORER air condition

24
[SR10040(ALL)06/95]
RWARNING
FAILURE TO REPLACE THE SAFETY BELT ASSEMBLY
UNDER THE ABOVE CONDITIONS COULD RESULT
IN SEVERE PERSONAL INJURIES IN THE EVENT OF
A COLLISION.
%*
[SR10200(ALL)10/95]
All safety belt assemblies, including retractors, buckles, front
seat belt buckle support assemblies (slide bar) (if equipped),
child safety seat tether bracket assemblies (if equipped), and
attaching hardware, should be inspected after any collision. Ford
recommends that all safety belt assemblies used in vehicles
involved in a collision be replaced. However, if the collision was
minor and a qualified technician finds that the belts do not
show damage and continue to operate properly, they do not
need to be replaced. Safety belt assemblies not in use during a
collision should also be inspected and replaced if either damage
or improper operation is noted.
%*
[SR10250(ALL)06/95]
Cleaning the Safety Belts
*
[SR10275(ALL)06/95]
Clean the safety belts with any mild soap solution that is
recommended for cleaning upholstery or carpets. Do not bleach
or dye the belt webbing because this may weaken it.
%*
[SR10300(ALL)06/95]
Air Bag Supplemental Restraint System
(SRS)
*
[SR10800(ALL)05/95]
The driver and right front passenger air bags are Supplemental
Restraint Systems (SRS), provided at these seating positions in
addition to the lap/shoulder belt, and are designed to
supplement the protection provided to properly belted
occupants in moderate to severe frontal collisions. The
supplemental air bag system does not provide restraint to the
lower body.
File:03unsrx.ex
Update:Thu Feb 29 09:02:31 1996

30
*
[SR13030(ALL)07/95]
RWARNING
Air bag system components get hot after inflation. Do
not touch them after inflation.
%*
[SR13050(ALL)05/95]
The air bag system uses a readiness light on the instrument
cluster and a tone to indicate the condition of the system. When
you turn the ignition key to the ON position, this light will
illuminate for approximately six (6) seconds and then turn off.
This indicates that the system is operating normally. NOTE:
Maintenance of the air bag system is not required.
*
[SR13060(ALL)05/95]
17-1/2 pica
art:0050087-A
Inflated driver-side air bag
File:03unsrx.ex
Update:Thu Feb 29 09:02:31 1996

Starting Your Explorer
77
*
[ST10300(ALL)01/95]
Improve your ventilation by keeping all air inlet vents clear of
snow, leaves, and other debris.
*
[ST10400(ALL)08/95]
If the engine is idling while you are stopped in an open area
for long periods of time, open the windows at least one inch
(2.5 cm). Also, adjust the heating or air conditioning system to
bring in outside air.
[ST10650(ALL)03/95]
n
HEATING Ð Set fan speed to medium or high, the function
control knob on any position except OFF and the
temperature control knob on any desired position.
[ST10700(ALL)03/95]
n
AIR CONDITIONING Ð Set fan speed to medium or high
with the function control knob on any position (except OFF
or MAX A/C) and the temperature control knob at a
comfortable level.
File:04unstx.ex
Update:Thu Feb 29 09:22:05 1996

Warning Lights and Gauges
105
[LG39200( X)04/94]
Check Brake Lamps
[LG39250( X)03/95]
This warning message is displayed when you turn on your
brakelamps by pressing the brake pedal and at least one of the
lamps is burned out.
[LG39300( X)04/94]
If you use additional lights, such as trailer lights, or if you
replace the headlamps or bulbs with equipment that is not equal
to the original equipment from Ford, you may get a false
ªCHECK LAMPSº warning or no warning at all.
[LG39350( X)06/94]
Air Ride Switch Off (If equipped)
[LG39400( X)03/95]
This warning message is displayed when the air suspension
switch, located in the rear jack stowage area on the left side, is
off. For information about the operation of the air suspension
switch, seeAutomatic ride control systemin the Index.
[LG39450( X)06/94]
Check Air Ride System (If equipped)
[LG39500( X)03/95]
This warning message is displayed when an air suspension
system fault has been detected. If this warning message is
displayed while driving, safely pull off the road at your earliest
convenience. If the vehicle is loaded beyond the recommended
maximum payload, the CHECK AIR RIDE SYSTEM message
may be displayed. This is a normal condition if the vehicle is
overloaded. To correct this condition, remove or redistribute the
payload per the recommended maximum requirements. Turn the
ignition switch from ON to OFF and ON again. If the warning
message reappears, turn the air suspension switch (located in
the rear jack stowage area on the left side) OFF and take your
vehicle to a dealership for service as soon as possible.
*
[LG39550( X)01/95]
Change Oil Soon or Oil Change Required
*
[LG39600( X)01/95]
One of these warning messages is displayed when the engine oil
life remaining is 5% or less. When Oil Life Left is between 5%
and 0%, the ªCHANGE OIL SOONº message will be displayed.
When Oil Life Left reaches 0%, the ªOIL CHANGE REQUIREDº
message will be displayed.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

110
[IP00400( X)03/95]
The main controls for the climate control system, lights, message
center, lamps, clocks and radio are on the instrument panel.
%*
[IP00475(ALL)09/95]
NOTE: Any cleaner or polish that increases the gloss (shine)
of the upper part of the instrument panel should be
avoided. The dull finish in this area is to help protect
the driver from undesirable windshield reflection.
%*
[IP00500(ALL)06/95]
The Climate Control Systems
*
[IP00601(ALL)12/91]
Your vehicle is equipped with a control assembly designed to
handle either a combination A/C-Heater System or a
Heater-Only System.
%*
[IP00801(ALL)10/93]
Instrument Panel Registers
*
[IP00901(ALL)02/95]
There are four registers in the instrument panel. Each of these
registers contains a louver assembly which can be manually
adjusted to direct airflow up, down, left and right. An
illustration of the register locations follows.
[IP01201(ALL)04/94]
7-1/2 pica art:0020099-D
Instrument panel registers
[IP01400(ALL)12/91]
Air Conditioning (A/C) Controls (Manual Air
Conditioning)
*
[IP01450(ALL)02/95]
The control for your air conditioning and heater system is
located at the center of the instrument panel below the radio
and will operate only when the ignition key is turned to the
ON position. Your air conditioner and heater will heat and/or
cool your vehicle interior depending on the function position
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996

Instrument Panel Controls
111 and temperature you select. The function selector control knob
allows you to select heating or cooling and determine where the
air will be directed. The temperature control knob setting
determines the temperature of the air that flows into the vehicle.
[IP01500(ALL)03/95]
10-1/2 pica
art:0020589-G
Climate control knobs
*
[IP01550(ALL)03/95]
To turn your air conditioner and heater system on, select any
position except OFF. This will turn the fan on and allow airflow
into the vehicle. To turn your air conditioner and heater off,
select OFF. This will turn the fan off and stop airflow from
coming into the vehicle.
*
[IP01600(ALL)03/95]
Temperature selection
[IP01650(ALL)03/95]
The temperature control knob is the rotating knob located at the
center of the control with tapered red and blue bands
surrounding most of the knob. The wide red part of the band
(full right) is the heat or warmer area. The wide blue area (full
left) is the cooling or cool temperature area. Any position
selected between full right and full left will give a temperature
between the two extreme temperatures.
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996

Instrument Panel Controls
113
[IP02150(ALL)08/95]
S(Panel and Floor)
[IP02200(ALL)03/95]
SelectSto direct airflow to the floor and through the
instrument panel registers at the same time. This selection can
be used to either heat or cool your vehicle. The air conditioner
will operate to cool the air if the outside temperature is about
50ÊF (10ÊC) orwarmer.
*
[IP02250(ALL)08/95]
R(Floor)
[IP02300(ALL)03/95]
SelectRto direct air to the floor. The air cannot be cooled in
theRposition but can be heated by rotating the temperature
knob into the red area.
[IP02350(ALL)08/95]
P(Floor and Defrost)
[IP02400(ALL)03/95]
SelectPto direct air to the floor and windshield defrosters at
the same time. If the outside temperature is about50ÊF (10ÊC)
or warmer, the air will also be dehumidified to remove
moisture. This feature will help prevent fogging in humid
weather. The air can be cooled or heated.
%*
[IP02450(ALL)08/95]
V(Defrost)
[IP02500(ALL)03/95]
SelectVto obtain maximum airflow to the windshield. Rotate
the temperature knob into the red area for the air temperature
required to defrost. When the outside temperature is about50ÊF
(10ÊC) or warmer, the airwill be dehumidified to remove
moisture. Rotate the
Hknob to increase the airflow.
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996

114
*
[IP02550(ALL)04/95]
Operating tips
*
[IP02600(ALL)02/95]
The following tips will help you to get the most satisfaction
from your air conditioning and heater system.
[IP02650(ALL)03/95]
n
In humid weather, selectVbefore starting your engine.
This will help to prevent windshield fogging. After a few
minutes of operation, you may select another function.
[IP02700(ALL)03/95]
n
To prevent humidity buildup inside your vehicle, always
drive with the air conditioner or heater system turned on.
*
[IP02750(ALL)03/95]
n
Do not put objects under the front seats that interfere with
the flow of air to the back seat area.
[IP02800(ALL)03/95]
n
Remove any snow, ice, or leaves from the air intake area of
your air conditioner and heater system that could block the
air intake. The intake area is located at the bottom of the
windshield.
[IP04500( X)03/95]
Electronic Automatic Temperature Control
(If equipped)
[IP04600( X)03/95]
The control for your Electronic Automatic Temperature Control
(EATC) is located at the center of the instrument panel below
the radio and will operate only when the ignition key is turned
on to the ON position.
[IP04700( X)03/95]
The EATC feature will maintain the temperature you select and
automatically control the airflow for your comfort. It also allows
you to override the automatic operation with manual override
buttons.
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996