1996 FORD EXPLORER ignition

164
*
[FV17505( X)02/95]5.
Press the door power unlock button 3 times.
*
[FV17510( X)02/95]6.
Turn the ignition key back to RUN within 30 seconds of
step 2.
*
[FV17515( X)02/95]7.
The horn should chirp once. If not, wait 30 seconds and
repeat steps 1 through 6.
[FV17520( X)06/04]8.
Press the door power unlock button twice.
*
[FV17525( X)02/95]9.
Press the door power lock button.
[FV17530( X)03/95]10.
The horn will chirp twice if the remote Memory Seat feature
was deactivated, three times (two short chirps followed by a
long chirp) if the remote Memory Seat feature was activated.
*
[FV17535( X)02/95]11.
Turn the ignition OFF.
[FV17540( X)03/95]12.
The horn will chirp once to confirm that you activated or
deactivated the remote Memory Seat feature.
[FV17542( X)03/95]
To reactivate the remote Memory Seat system, simply repeat the
instructions for deactivating the system. By reentering the code
that deactivates the remote Memory Seat, the keyless entry
system reinstates the feature.
[FV17545( X)09/95]
NOTE: The Memory Seat function will continue to work from
the door switch even when deactivated at the remote
keyless entry module. Only remote Memory Seat
recall can be deactivated.
%*
[FV17551(ALL)02/95]
Replacing the batteries
*
[FV17601(ALL)02/95]
The remote entry transmitter is powered by two coin type
three-volt lithium 2016 batteries (included) that should last for
several years of normal use. If you notice a significant decrease
in operating range, the batteries should be replaced.
Replacement batteries can be purchased at most pharmacies,
watch stores or at your Ford or Lincoln-Mercury dealer.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

166
%*
[FV18101(ALL)02/95]
Replacing lost transmitters
[FV18200(ALL)07/95]
In the event a transmitter is lost, you should take your vehicle's
transmitters to your dealer to have the remote entry system
deprogrammed for the lost transmitter. This is necessary to
prevent further unauthorized use of the lost transmitter.
*
[FV18301(ALL)02/95]
You can also purchase additional transmitters (up to 4
transmitters can be used) from your dealer. You will need to
take all your transmitters to the dealer so they can program
them to the remote entry system all at the same time.
%*
[FV18601(ALL)04/95]
Illuminated Entry System (If equipped)
*
[FV18701(ALL)06/95]
This system will provide illumination of the vehicle's interior
courtesy lamps when either outside front door handle is pulled
or when the remote entry system is used to unlock the door or
sound the personal alarm. The system will automatically turn
off after approximately 25 seconds or when the ignition is
turned to the RUN or ACC position.
*
[FV18801(ALL)09/95]
NOTE: The inside lights will not turn off if you have turned
them on with the dimmer thumbwheel or if any door
is open.
[FV18810( X)10/94]
Delayed Accessory
[FV18815( X)08/94]
This feature provides power to operate the power windows and
power moon roof for 10 minutes after the ignition switch is
turned from the RUN to the OFF position.
[FV18820( X)06/94]
If either front door is opened during the 10 minute period the
delayed accessory feature will be disabled.
%*
[FV18900(ALL)08/94]
Battery Saver
*
[FV19000(ALL)03/95]
When the ignition is turned off, the vehicle will turn off battery
voltage to all of these lights after 40 minutes: glove box, engine
compartment, overhead console, mirror, courtesy and
interior (including cargo) lamps.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

Features
167
[FV19100( X)03/95]
This will prevent draining of the battery if these lights have
been left on inadvertently or if a door or the liftgate is not
completely closed. Battery voltage to these lamps will be
restored when the remote entry transmitter is used, any door is
opened, the liftgate is opened, or the ignition key is turned ON
again.
%*
[FV19104(ALL)09/95]
Anti-Theft Alarm System (If equipped)
*
[FV19106(ALL)05/95]
When armed, this system helps protect your vehicle against
break-ins or theft.
%*
[FV19109(ALL)05/95]
When an unauthorized entry occurs, the system triggers and
will:
*
[FV19112( X)02/95]
n
flash the headlamps, parking lamps, and theft indicator lamp
*
[FV19115(ALL)06/95]
n
honk the horn
*
[FV19118(ALL)05/95]
n
disable the starting circuit to prevent the vehicle from being
started
% [FV19121(ALL)02/95]
Arming the System
*
[FV19124(ALL)04/95]
The system is ready to arm any time the ignition switch is
turned OFF and the alarm is not triggered or sounding. Any of
the following events will prearm the anti-theft system:
[FV19130(ALL)04/95]
n
Pressing the remote entry transmitter LOCK button to lock
the doors (with the doors open or closed),
[FV19133( X)04/95]
n
Pressing the 7/8 and 9/0 buttons on the keyless entry
keypad at the same time to lock the doors (with the doors
open or closed), or
*
[FV19136(ALL)04/95]
n
Opening a door and pressing the power door lock button to
lock the doors.
*
[FV19140( X)04/95]
If a door, liftgate or liftgate window is open, the anti-theft
system is prearmed and waiting for all doors to close. The
THEFT indicator in the instrument panel will light continuously
while the system is prearmed.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

168
[FV19145( X)04/95]
n
Close all doors, liftgate and liftgate window
*
[FV19149( X)04/95]
Once all doors, liftgate and liftgate window are closed, if any
were open, the system will begin a 30 second countdown to
become armed. The 30 second countdown allows people who
may still be in the vehicle time to exit without triggering the
alarm. The THEFT indicator will glow steadily until the system
is armed. When the system is armed, the THEFT indicator will
begin to flash with short flashes every 2 seconds until the
system is triggered or disarmed.
*
[FV19153( X)02/95]
Remember, all doors, the liftgate and liftgate window must be
fully closed for the anti-theft system to arm. If a door, the
liftgate or liftgate window has been left open or ajar, and you
press the remote entry transmitter twice to confirm the doors
are locked, two short horn chirps will warn you that the
anti-theft system is not arming.
*
[FV19155(ALL)02/95]
When you get a single horn chirp by pressing the LOCK button
twice within 5 seconds on your remote entry transmitter, you
can be assured that all doors are locked and the anti-theft
system is arming.
% [FV19157(ALL)02/95]
Disarming the System
*
[FV19160(ALL)10/95]
An armed or activated system can be disarmed if you:
*
[FV19162(ALL)04/95]
n
Unlock the doors by pressing the remote entry transmitter
UNLOCK button.
*
[FV19163( X)04/95]
n
Unlock the doors by entering the unlock code on the keyless
entry keypad.
*
[FV19187( X)02/95]
n
Unlock any door or the liftgate with a key.
*
[FV19190(ALL)02/95]
n
Turn ignition to the ON or ACC position.
*
[FV19196(ALL)04/95]
n
Pressing the remote entry PANIC button will disarm the
anti-theft system only when the anti-theft alarm is triggered
and sounding.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

170
[FV19224( X)03/95]
In 4WD Low, the automatic ride control system raises the
vehicle approximately two inches above its lowest height. Shock
dampening is locked in firm mode. The height change improves
body clearance. The combination of firm dampening and the
height change also provides maximum suspension feedback for
improved off-road safety and performance.
[FV19226( X)03/95]
The vehicle will drop to its lowest position when the ignition is
turned OFF to provide ease of entry and exit of the vehicle.
[FV19229( X)03/95]
As a safety consideration, whenever a door is opened, including
the liftgate and liftgate glass, the system memorizes and
maintains the height at the moment the door was opened. The
system will maintain this height until either the doors are all
closed or vehicle speed exceeds 10 mph (16 km/h).
[FV19234( X)03/95]
An on-board air compressor and solenoids are used to raise and
lower the vehicle. It is normal to occasionally hear a buzz or
clicking from the vehicle even when the ignition is turned off.
The system stays energized for forty minutes after ignition is
turned off to compensate for any load changes made after the
vehicle is parked.
[FV19237( X)05/95]
The automatic ride control system operation can be monitored
through the message center. Refer toMessage Centerin the
Warning Lights and Gaugeschapter for more details.
[FV19240( X)08/94]
Service Switch
[FV19243( X)08/94]
The automatic ride control service switch is mounted in the jack
storage area. The switch should be turned off to disable the
automatic ride control system during jacking, hoisting, towing,
or transport of the vehicle to avoid unexpected vehicle
movement.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

172
[FV20801( X)05/95]
Flip quarter window (2 door model only)
[FV20900( X)03/91]
To open, press outward on the window latches, then depress
the levers on each side of the latch and pull inward. Move the
latch out and into the open position. To close, depress the levers
on each side of the latch. Lift the latch and pull inward, then
press latch outward to lock the levers.
[FV21000( X)03/90]
10-1/2 pica
art:0020680-B
Flip quarter window
%*
[FV22901(ALL)03/91]
Using the Power Windows (If equipped)
[FV23001(ALL)08/94]
Each door has a power control that opens and closes the
window on that door. The driver's door has a master control
switch that operates all door windows. You must place the
ignition switch in the ON or ACC position to use your power
window controls.
[FV23101( X)02/92]
One touch down driver's power window operation
[FV23201( X)01/95]
The one touch down power window feature allows you to
completely open the driver's window without holding down the
window switch. To open the window completely, press the
window switch to the down position for less than 1/2 second,
then release it. If the switch is pressed while the window is
going down, the window will stop at that position.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

Electronic Sound Systems
209
%*
[AS00600( X)06/95]
Luxury Audio System
*
[AS00700( X)08/95]
Using the Controls on Your New Radio
*
[AS00800( X)08/95]
How to turn the radio on and off
*
[AS00900( X)01/95]
Press the “VOL/PUSH ON” knob to turn the radio on. Press
again to turn it off.
*
[AS01000( X)08/95]
How to adjust the volume
[AS01100( X)06/95]
Turn the “VOL/PUSH ON” knob clockwise to increase the
volume and counterclockwise to decrease the volume.
[AS01200( X)09/95]
NOTE: If the volume level is set above a certain listening
level when the ignition switch is turned off, when the
ignition switch is turned back on, the volume will
come back to a “nominal” listening level. However, if
the radio power is turned off (with the “VOL/PUSH
ON” button) and the volume is at a low level, the
volume will remain in the position it was set at when
radio power is switched back on.
*
[AS01300( X)08/95]
Selecting the AM or FM frequency band
*
[AS01400( X)04/95]
Push the “AM/FM” button to select the desired frequency band.
Pushing the “AM/FM” button causes the frequency band to
switch from “AM” to “FM1” to “FM2” to “AM”, changing one
band to the next each time the button is pressed. These
functions are used with the station memory buttons described
underHow to tune radio stations.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
219
*
[AS08200( X)08/95]


Protect cassettes from exposure to direct sunlight, high
humidity and extreme heat or cold. If they are exposed to
extreme conditions, allow them to reach a moderate
temperature before playing.
*
[AS08300( X)08/95]


If a tape is loose inside the cassette, tighten it before playing
by putting your finger or a pencil into one of the holes and
turning the hub until the tape is tight.
*
[AS08400( X)08/95]


Loose labels on cassette tapes can become lodged in the
mechanism. Remove any loose label material before inserting
a cassette.
*
[AS08500( X)08/95]


Do not leave a tape in the cassette tape player when not in
use. High heat in the vehicle can cause the cassette to warp.
%*
[AS08600( X)08/95]
Clock Operation
*
[AS08700( X)08/95]
How to view the clock mode
[AS08800( X)09/94]
Press the“CLK”button to display time. The time will continue
to be displayed until a radio or tape function is chosen. After
approximately 10 seconds, the time will again appear in the
display. To display radio or tape information only, press the
“CLK”button a second time.
[AS08900( X)09/95]
NOTE: The clock can be displayed or set whether the ignition
is on or off as long as the“CLK”button is depressed.
*
[AS09000( X)08/95]
How to set the clock
*
[AS09100( X)08/95]1.
Turn the radio on.
[AS09200( X)04/00]2.
Press and hold the“CLK”button, press the right (
a) side of
the“SEEK”button to increase hours. Press the left (
b) side
of the button to decrease hours. Press the right (
a) side of
the“TUNE”or“TUNE DISCS”button to increase minutes.
Press the left (
b) side of the button to decrease minutes.
*
[AS09300( X)09/95]
NOTE: The clock displays 12-hour time with no AM/PM
indications.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996