1996 FORD EXPLORER fuel

104
*
[LG38450( X)01/95]
Low Fuel Level
*
[LG38500( X)01/95]
This warning message is displayed when you have
approximately 50 miles (80 km) left before you run out of fuel.
*
[LG38550( X)01/95]
Low Oil Level
*
[LG38600( X)01/95]
This warning message is displayed when your engine oil level is
low. If this warning message is displayed, check the level of the
engine oil.
*
[LG38650( X)02/95]
To check your oil:
*
[LG38700( X)05/95]1.
Park your vehicle on level ground, turn off the engine and
wait at least 5 minutes for the oil to drain back into the oil
pan.
*
[LG38750( X)01/95]2.
Use the dipstick to check the oil. If the level is low, add oil,
but do not overfill.
*
[LG38800( X)01/95]
If you are parked on a steep incline, the LOW OIL LEVEL
warning may come on when you start your vehicle, even
though the oil is at the correct level.
*
[LG38850( X)01/95]
For information about adding oil, seeEngine oilin the Index.
%*
[LG38900( X)05/95]
Low Washer Fluid Light
*
[LG38950( X)04/95]
This warning message is displayed when the washer fluid
reservoir is less than one quarter full.
[LG39000( X)01/95]
Check Head Lamps
[LG39050( X)08/94]
This warning message is displayed when you turn on your
headlamps and at least one of them is burned out. A high beam
headlamp burn out is not monitored.
[LG39100( X)04/94]
Check Tail Lamps
[LG39150( X)04/94]
This warning message is displayed when you turn on your rear
parking (tail) lamps and at least one of them is burned out.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

142
[SC08300(ALL)03/95]3.
Press SET ACCEL switch and release it immediately. This
will set your speed. If you keep this switch pressed, your
speed will continue to increase and will not be set until the
switch is released.
*
[SC08500(ALL)08/95]4.
Take your foot off the accelerator pedal. Your vehicle will
maintain the speed you set.
*
[SC08600(ALL)08/95]
If you drive up or down a steep hill, your vehicle may
momentarily slow down or speed up, even though the speed
control is on. This is normal.
[SC08630(ALL)09/95]
NOTE: If your vehicle is equipped with an automatic
transmission, and if your speed increases above your
set speed while driving in
j(Overdrive) on a
downhill grade, you may want to shift to D (Drive) to
reduce vehicle speed. This can be accomplished by
pushing in the Transmission Control switch which is
located on the end of the gearshift lever. The speed
control cannot reduce the vehicle speed if it goes
above your set speed on a downhill grade. For the
best fuel economy during normal driving conditions,
leave the shift select in
j(Overdrive), or resume as
soon as practical.
[SC08675(ALL)03/95]
NOTE: If your vehicle is equipped with a 5 speed manual
transmission, and if your speed increases above your
set speed while driving in 5 (Fifth) gear on a downhill
grade, you may want to shift to 4 (Fourth) gear to
reduce vehicle speed. Depressing the clutch pedal
cancels speed control, therefore speed control must be
reset by pressing the SET ACCEL or RESUME
switches. Speed control cannot reduce the vehicle
speed if it goes above your set speed on a downhill
grade.
File:07unscx.ex
Update:Thu Feb 29 09:06:35 1996

Steering Column Controls
143
*
[SC08700(ALL)08/95]
RWARNING
Do not use the speed control in heavy traffic or on roads
that are winding, slippery, or unpaved.
*
[SC08801(ALL)05/95]
In mountainous areas, at higher elevations, or when pulling a
trailer, the speed control may not be able to maintain the preset
speed with the transmission in
j(Overdrive).
*
[SC08850(ALL)06/92]
If your vehicle comes with a 5-speed manual transmission, you
may prefer to drive in 4 (Fourth) gear, in mountainous areas or
at high altitudes, to improve speed control performance.
*
[SC09275(ALL)12/91]
In order to downshift (with a manual transmission) with the
speed control operating, you must press either the brake or
clutch pedal long enough to disengage the speed control. Wait a
second before depressing the clutch again and making the shift
so that the speed control can fully return to the idle position.
*
[SC09325(ALL)05/95]
RWARNING
Do not shift the transmission into N (Neutral) with the
speed control on.
[SC09350(ALL)03/95]
To maintain a preset speed under the above conditions, with
electronically controlled transmissions Ð press the Transmission
Control Switch (TCS). The indicator light will turn on and
illuminate the words ªO/D OFF.º This will cancel ªOverdrive.º
You can press the Transmission Control Switch (TCS) on or off
at any speed. For the best fuel economy during normal driving
conditions, press the Transmission Control Switch (TCS) to turn
off the light. This allows overdrive operation.
File:07unscx.ex
Update:Thu Feb 29 09:06:35 1996

245
Driving Your Explorer
*
[DR00350(ALL)06/95]
Procedures for driving your vehicle will vary depending on
which type of transmission your vehicle has.
*
[DR00600(ALL)06/95]
n
a manual transmission
[DR05475( X)12/95]
n
an Automatic Overdrive Transmission 4R55E or 4R70W
[DR05700(ALL)1/96]
Automatic Transmission Operation
4R44E/4R55E/4R70W
*
[DR08715(ALL)12/95]
The 4R44E, 4R55E and 4R70W transmissions are electronically
controlled four speed overdrive automatic transmissions with
lockup torque converter. Transmission operation is controlled by
the Powertrain Control Module (PCM).
*
[DR08720(ALL)08/95]
The PCM will automatically adjust transmission operation to
make up for varying conditions. Several sensors located on the
engine and transmission such as throttle position, engine speed,
vehicle speed and transmission temperature are used by the
PCM to shift the transmission into a higher or lower gear when
required for the best performance and fuel economy. For
example, you may notice that the transmission will upshift to a
higher gear more quickly when the vehicle has not reached
normal operating temperature.
*
[DR08730(ALL)08/95]
The PCM also controls the transmission's Torque Converter
Clutch (TCC) to further raise vehicle performance and fuel
economy. The TCC will engage when the transmission operating
temperature and other conditions determined by the PCM have
been met. Engagement of the clutch may be noted as a decrease
in engine speed.
[DR08740(ALL)03/95]
To help in troubleshooting, the PCM continually performs
self-tests on the electronic control system and, if any faults are
detected, stores them in memory. The Overdrive Off Indicator
Light (O/D OFF), which is located on the instrument cluster,
may flash steadily if a malfunction has been detected. If the
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

248
%*
[DR09200(ALL)01/95]
R (Reverse)
*
[DR09300(ALL)08/95]
With the gearshift in the R (Reverse) position, the vehicle will
move backward. You should always come to a complete stop
before shifting into or out of R (Reverse).
*
[DR09350(ALL)01/95]
N (Neutral)
*
[DR09375(ALL)01/95]
With the gearshift in the N (Neutral) position, the vehicle can be
started and is free to roll. Hold the brake pedal down while in
this position.
%*
[DR09400(ALL)01/95]
Driving
%*
[DR09500(ALL)04/95]
When to use
j(Overdrive)
*
[DR09600(ALL)04/95]
This is the normal driving position. As the vehicle picks up
speed, automatic upshifts to second, third and fourth gears will
occur when
jOverdrive is chosen on the selector and the
transmission control switch has not been pressed. The
transmission will shift into the correct gear when the right
speed is achieved, for the accelerator pedal position you have
chosen.
*
[DR09700(ALL)03/94]
When to use Drive
[DR09800(ALL)06/95]
You will note there is not a drive position on your gearshift
indicator. However, you will find a transmission control switch
labeled O/D ON/OFF located on the end of the gearshift lever.
Press this switch and the O/D OFF indicator light will
illuminate on the instrument cluster. With overdrive cancelled
and the O/D OFF indicator light illuminated, the transmission
will operate in gears one through three. This is useful if you
experience frequent downshift/upshift conditions, when
operating with a heavy load or in hilly terrain, or if additional
engine braking is useful. However, shift back to
j(Overdrive)
whenever practical for optimum powertrain cooling and fuel
economy. This can be accomplished by pushing the transmission
control switch again, to cancel the O/D OFF control and light.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

254
*
[DR15100(ALL)03/95]
When you slow down or climb a steep hill, always downshift
before the engine starts to lose power. Downshifting reduces the
chance of stalling and gives your vehicle better acceleration to
increase speed again.
*
[DR15200(ALL)03/95]
When you drive down steep hills, downshifting helps you keep
a safe speed and helps prevent unnecessary wear on the brakes.
*
[DR15300(ALL)03/95]
When you come to a stop, do not downshift through each gear.
Disengage the clutch and use the brake as necessary.
Downshifting through the gears decreases your vehicle's fuel
economy.
*
[DR15400(ALL)05/95]
RWARNING
Continued use of a damaged or worn clutch, prolonged
clutch slippage or downshifting at excessive speeds can
result in a failure of the engine, transmission or clutch
components.
*
[DR15500(ALL)03/91]
Transmission Function
[DR15600(ALL)10/94]
Upshift at the speeds specified in the chart. All forward gears
are synchronized allowing you to shift into them with your
vehicle in motion. The clutch pedal should be fully depressed
when shifting.
*
[DR15625(ALL)04/94]
NOTE: Shifting during extremely low rpm's can result in a
momentary audible rattle which disappears as vehicle
rpm's are increased. Shifting at higher speeds will
eliminate this sound.
*
[DR15700(ALL)03/95]
Parking
*
[DR15800(ALL)01/95]
To park your vehicle, apply the service brake pedal, and shift
into N (Neutral) while still maintaining pressure on the service
brake. Set the parking brake fully. Shift into first and turn off
the ignition.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

256
%*
[DR16101(ALL)03/95]
Four-Wheel Drive (4WD) System
(If equipped)
[DR16130(ALL)10/94]
When you select the 4WD mode, your vehicle uses all four
wheels to power itself. This increases traction, enabling you to
drive your 4x4 over terrain and road conditions not travelled
normally by two-wheel drive vehicles.
*
[DR16160(ALL)10/94]
Power is supplied to all four wheels through a transfer case that
allows you to select four-wheel drive when necessary. Methods
for engaging and disengaging 4WD and low range will depend
on which system your vehicle has.
[DR17585( X)01/95]
4WD Systems Ð Control Trac
[DR17615( X)01/95]
The Control Trac 4WD system functions in three modes. In
two-wheel drive mode, power is delivered only to the rear axle.
The 4WD AUTO position provides four-wheel drive with full
power delivered to the rear axle, and to the front axle as
required for increased traction. The 4WD LOW position
provides four-wheel drive with full power delivered to the front
and rear axles when above average power is required at
reduced speeds.
[DR17645( X)01/95]
Four-wheel drive operation (4WD LOW) on dry pavement is not
recommended. Operating the vehicle in 4WD LOW on dry
pavement will increase noise, vibration, tire wear, and decrease
fuel economy.
[DR17690( X)08/94]
Control Trac system indicator lights
[DR17735( X)03/95]
A 4WD indicator light and a 4WD LOW indicator light are
located in the instrument cluster. If either light flashes, take
your vehicle in for service.
[DR17750(ALL)01/95]
n
Two-Wheel Drive mode Ð Neither the 4WD nor the 4WD
LOW lights are lit.
[DR17790( X)1/96]
n
4WD Auto mode Ð Only the 4WD light is lit.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
275
*
[DR30310(ALL)06/92]
n
GCWR (Gross Combined Weight Rating)
*
[DR30320(ALL)06/92]
n
Maximum Trailer Weight Rating
*
[DR30330(ALL)06/92]
n
Maximum Trailer Weight
*
[DR30340(ALL)06/92]
n
Trailer Weight Range
*
[DR30351(ALL)03/91]
Base Curb Weight
*
[DR30401(ALL)03/94]
The Base Curb Weight is the weight of the vehicle including
fuel, coolants, lubricants, emergency tools, spare wheel and tire.
It also includes any equipment that isstandardon that model. It
does not include passengers, cargo or optional equipment
installed by factory, dealer, aftermarket supplier or customer.
*
[DR30451(ALL)03/91]
Payload
*
[DR30501(ALL)03/91]
Payload is the combined, maximum allowable weight of cargo,
occupants and optional equipment that the truck is designed to
carry. It is Gross Vehicle Weight Rating minus the base curb
weight.
*
[DR30550(ALL)03/91]
Gross Vehicle Weight (GVW)
*
[DR30601(ALL)05/95]
If you add base curb weight and the weight of a load (including
passengers, cargo and optional equipment) being carried at a
particular time, you get the Gross Vehicle Weight (GVW).
*
[DR30650(ALL)08/95]
It is important to remember that GVWis not a limit or a
specification.If an owner loads up a vehicle and weighs it, that's
the GVW at that moment. If the owner piles on more of a load
and weighs it again, that becomes the GVW.
%*
[DR30701(ALL)03/91]
Gross Vehicle Weight Rating (GVWR)
*
[DR30750(ALL)10/94]
To avoid overloading a vehicle, the owner should observe the
manufacturer's specified Gross Vehicle Weight Rating. The
GVWR is the maximum total weight of base vehicle, passengers,
optional components and cargo that a particular vehicle was
designed to carry.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996