1996 FORD E SERIES ECU

323 %
*
[SV33651( ALL)02/95]
Checking the Automatic Transmission
Fluid
*
[SV33701( ALL)05/95]
It is preferable to check the transmission fluid
level at normal operating temperature
150ÊF-170ÊF (66ÊC-77ÊC),after approximately 20
miles (30 km) of driving. However, if necessary,
you can check the fluid level without having to
drive 20 miles (30 km) to obtain a normal
operating temperature if outside temperatures
are above50ÊF (10ÊC).
*
[SV33801( ALL)01/95]
NOTE: If the vehicle has been operated for an
extended period at high speeds or in
city traffic during hot weather, or
pulling a trailer, the vehicle should be
turned off for about 30 minutes to
allow the fluid to cool before checking.
*
[SV33910( ALL)06/95]
With the vehicle on a level surface, start the
engine and move the transmission shift selector
through all of the gear ranges allowing sufficient
time for each position to engage. Securely latch
the transmission shift selector in the P (Park)
position, fully set the parking brake and leave
the engine running.
*
[SV33930( ALL)10/89]
RWARNING
Your vehicle should not be driven if the
fluid level is below the bottom hole on
the dipstick and outside temperatures are
above50ÊF (10ÊC).
*
[SV33940( ALL)02/95]
Wipe off the dipstick cap, pull the dipstick out
and wipe the indicator end clean. Put the
dipstick back into the filler tube and make sure
it is fully seated. Pull the dipstick out and read
the fluid level.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

343
*
[SV46900(BEF )03/95]
Installing the headlamp bulb
*
[SV47000(BEF )02/95]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
*
[SV47100(BEF )02/95]
2. Slip the bulb retaining ring over the plastic
base until it contacts the rear of the socket.
Lock the ring into the socket by rotating it
clockwise until you feel a ªstopº.
[SV47250( E )12/91]
3. Reposition the three adjuster screws into the
retaining holes and hold while pushing the
two black tabs downward to engage the
ends of the adjuster screws. You will hear a
ªsnapº when the tabs are properly engaged.
Make sure lamp is secured properly by
pulling it forward. If it is loose, remove
lamp and reinstall.
*
[SV47300(BEF )02/95]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
*
[SV47406( E )02/95]
High-Mount Brakelamp Bulbs
[SV47410( E )03/91]
E-150 Ð E-350 without cargo lamp attached
[SV47420( E )03/91]
To remove/install or replace a bulb:
[SV47430( E )03/91]
1. Remove the two screws that secure the lamp
and lift up from the vehicle.
[SV47440( E )03/91]
2. Remove the socket that contains the
burned-out bulb and replace the bulb.
[SV47450( E )03/91]
3. To install a bulb, reverse the procedures
above.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

344 [SV47460( E )03/91]E-150 Ð E-350 with cargo lamp attached
[SV47470( E )03/91]
To remove/install or replace a bulb:
[SV47480( E )03/91]
1. Remove the two screws that secure the
Hi-mount stop lamp/cargo lamp and lift the
assembly from the vehicle.
[SV47490( E )03/91]
2. After removing the two screws that secure
the lens, remove the cargo lamp lens.
[SV47501( E )03/91]
3. Remove the two screws attaching the cargo
lamp to the Hi-mount stop lamp.
[SV47510( E )03/91]
4. Remove or replace the burned-out bulb(s) in
the Hi-mount stop lamp.
[SV47520( E )03/91]
5. To install a bulb, reverse the procedures
above.
[SV47530( E )12/91]
half page art:0020852-B
Replacing the stop lamp bulb
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996