1996 FORD CROWN VICTORIA buttons

124
*
[FV03900( BCGV)04/95]
When you bought your vehicle, you were given
a computer code that operates the system for
your vehicle. For your convenience, we have
duplicated this code in three places.
*
[FV04000( BCGV)02/95]
The code is:
*
[FV04100( BCGV)02/95]
q
on your owner's wallet card found in the
glove compartment
[FV04400( BCGV)02/95]
q
taped to the underside of the trunk lid
[FV04800( GV)10/94]
q
taped to the computer module behind the
driver's door trim panel.
[FV04925( BCGV)05/95]
When you use this entry system, the illuminated
entry system turns on the interior lights for 25
seconds and the buttons on the keypad light up.
Do not push the buttons with a key, ballpoint
pen, pencil, or any other hard object. These
objects could damage the buttons.
%*
[FV04950( BCGV)02/95]
Unlocking the doors with the keyless entry
system
[FV05000( BCGV)02/95]
You must unlock the driver's door before you
unlock any of the other doors or trunk. If you
let more than five seconds pass between pressing
numbers, the system shuts down, and you have
to enter the code again. The system has shut
down if the keypad light is out. If the keyless
entry system does not work properly, use the
key or transmitter(s) to lock and unlock the
doors or unlock the trunk.
*
[FV05100( BCGV)02/95]
1. To unlock the driver's door, enter the factory
code or your personal code. All codes have
five numbers. After you press the fifth
number, the driver's door unlocks.
[FV05140( GV)03/92]
2. To unlock the passenger's doors, press the
3/4 button within five seconds of unlocking
the driver's door or trunk, or re-enter the
code to open the driver's door, then press
3/4.
File:rcfvv.ex
Update:Wed Jan 31 10:27:22 1996

126
*
[FV05901( BCGV)02/95]
If you do not want to use the Autolock feature,
it can be deactivated by using the buttons for
the keyless entry system.
[FV05950( BCGV)02/95]
To deactivate the Autolock feature:
[FV06001( BCGV)02/95]
1. Enter your permanent five-digit entry code
(not the user code you may have set).
*
[FV06051( BCGV)02/95]
2. Within 5 seconds, press and hold 7/8.
*
[FV06101( BCGV)02/95]
3. Within 5 more seconds, press and release
3/4.
*
[FV06200( BCGV)02/95]
4. Release 7/8.
*
[FV06300( BCGV)02/95]
To reactivate the Autolock feature, simply repeat
the instructions for deactivating the system. The
Autolock feature can be turned on and off using
the instructions above.
%*
[FV06800( BCGV)02/95]
Programming your own entry code
*
[FV06900( BCGV)01/95]
You can program a personal code to unlock
your vehicle. This code does not replace the
permanent code that the dealership gave you.
Use your personal code in the same manner as
you would your original code.
*
[FV07000( BCGV)02/95]
To program your own code:
*
[FV07050( BCGV)02/95]
1. Select five digits for your personal code.
[FV07100( BCGV)02/95]
2. Enter the permanent code that the dealership
gave you.
*
[FV07200( BCGV)02/95]
3. Within five seconds, press 1/2.
*
[FV07300( BCGV)02/95]
4. Within five seconds of pressing 1/2, enter
your personal code, pressing each digit
within five seconds of the previous digit.
File:rcfvv.ex
Update:Wed Jan 31 10:27:22 1996

127 [FV07350( GV)10/94]
5. Five seconds after you press the fifth digit,
your door lock system will lock and unlock
the vehicle doors to confirm successful
programming.
*
[FV07400( BCGV)02/95]
The keyless entry system registers this
second code. To open your vehicle, you can
now use either code. The module remembers
only one personal code at a time. Entering a
second personal code will erase the first,
replacing it with the new second one.
*
[FV07500( BCGV)02/95]
To erase your personal code:
*
[FV07600( BCGV)02/95]
1. Enter the original permanent code.
[FV07750( GV)10/94]
2. Press and release 1/2 within five seconds of
Step 1.
[FV07850( GV)10/94]
3. Press the 1/2 button a second time and hold
for two seconds.
*
[FV07900( BCGV)02/95]
The keyless entry system automatically
erases your personal code. The system will
now only respond to the permanent code.
*
[FV07950( BCGV)02/95]
Do not set a code that presents the numbers in
sequential order, such as 1/2, 3/4, 5/6, 7/8, 9/0.
Studies show that people who idly press the
buttons usually press a sequential pattern. Also,
do not select a code that uses the same button
five times. Thieves can easily figure out these
types of codes.
[FV07955( GV)10/94]
Your door lock system will lock and unlock the
vehicle doors to confirm successful erasure. The
system will now only respond to the permanent
code.
File:rcfvv.ex
Update:Wed Jan 31 10:27:22 1996

128 % [FV08007( GV)10/94]Battery Saver
*
[FV08012( GV)01/95]
When the ignition is turned off, the vehicle will
turn off battery voltage to the vehicle lamps as
follows:
*
[FV08016( GV)01/95]
q
Courtesy lights (lights which come on when a
door is opened): after 10 minutes.
[FV08020( GV)10/94]
q
Map/Glove compartment/Trunk/Hood
lamps: after 30 minutes.
[FV08023( GV)10/94]
q
Headlamps/Park lamps (only if headlamp
switch is left in Headlamp position): after 10
minutes.
*
[FV08027( BCGV)02/95]
This will prevent draining of the battery if those
lights have been left on inadvertently or if a
door is not completely closed. Battery voltage to
these lamps will be restored when the outside
front door handles are lifted, the keyless entry
keypad is used, the remote entry transmitter is
used, any door is opened, the trunk is opened,
or the ignition key is turned to the ON position.
%
*
[FV08030( ALL)02/95]
Remote Entry System
(If equipped)
*
[FV08036( ALL)03/94]
If your vehicle has the remote entry system, you
can lock and unlock the vehicle doors and open
the trunk without using a key. The remote also
has a personal alarm feature. The buttons for the
system are located on the hand held
transmitter(s) that came with your vehicle.
*
[FV08040( ALL)02/95]
The system will work with up to four
transmitters. Your vehicle came with two
transmitters. Additional transmitters can be
ordered from your dealer.
[FV08047( GV)10/94]
The remote entry features only operate with the
transmission in P (Park) or N (Neutral).
File:rcfvv.ex
Update:Wed Jan 31 10:27:22 1996

130 [FV08111( GV)10/94]To reactivate the Horn Chirp feature, simply
repeat the instructions for deactivating the
feature.
*
[FV08114( ALL)02/95]
Activating the remote personal alarm
*
[FV08120( ALL)02/95]
If you wish to activate the remote personal
alarm, press the PANIC button. This will honk
the horn and flash the low beam headlamps and
tail lamps for approximately two minutes and
forty-five seconds. You can turn it OFF by
pressing the PANIC button again or by turning
the ignition key to the RUN position.
[FV08125( ALL)05/94]
When you use the remote entry UNLOCK,
TRUNK or PANIC buttons, the illuminated entry
system turns on the interior lights for 25
seconds. You can turn these lights off with the
LOCK button or by turning the ignition to the
RUN position. The interior lights will not turn
off if you have turned them on manually or if a
door is open.
%*
[FV08725( ALL)02/95]
Replacing the batteries
*
[FV08760( GV)01/95]
The remote entry transmitter is powered by two
coin type three-volt lithium 1616
batteries (included) that should last for several
years of normal use. If you notice a significant
decrease in operating range, the batteries should
be replaced. Replacement batteries can be
purchased at most pharmacies, watch stores or
at your Ford or Lincoln-Mercury dealer.
*
[FV08775( ALL)02/95]
NOTE: The operating range of the remote
entry system can also be affected by
weather conditions (such as very cold
temperatures) or structures around the
vehicle (buildings, other vehicles, radio
and TV towers, etc.). Typical operating
range will allow you to be up to 33
feet (10 meters) away from your
vehicle.
File:rcfvv.ex
Update:Wed Jan 31 10:27:22 1996

138 %
*
[FV19000( V)05/95]
Programmable Memory Ð Seat and
Mirrors (If equipped)
*
[FV19025( V)01/95]
If your vehicle is equipped with this option, you
can store settings for three seat and mirror
positions. This allows you to get into your
vehicle and simply push the preset button(s) to
automatically have your seat and mirrors in the
proper position.
[FV19050( V)03/94]
one third page art:0011290-A
Setting the programmable memory seat switch
[FV19075( V)06/94]
1. Adjust your seat to the desired position.
[FV19100( V)06/94]
2. Press the ªSETº button. A small lamp inside
the button will light up. This tells you that
you have five seconds to program your seat
position.
[FV19125( V)06/94]
3. Press ª1º button within five (5) seconds. You
now have set in memory the first seat
position. Set the second seat position by
adjusting the seat, pressing the SET button
and pushing the ª2º button within five (5)
seconds. A third seat position can be set in
the same manner as above by pushing ª1º
and ª2º buttons simultaneously.
File:rcfvv.ex
Update:Wed Jan 31 10:27:22 1996

151
*
[AS10319( GV)03/95]
Luxury Audio System
*
[AS10320( GV)02/95]
Using the Controls on Your New Radio
*
[AS10330( GV)04/95]
How to turn the radio on and off
*
[AS10340( GV)01/95]
Press the ªVOL/PUSH ONº knob to turn the
radio on. Press again to turn it off.
*
[AS10351( GV)04/95]
How to adjust the volume
*
[AS10352( GV)05/95]
Turn the ªVOL/PUSH ONº knob to the right to
increase the volume and to the left to decrease
the volume.
[AS10353( V)04/94]
NOTE: If the volume level is set above a
certain listening level when the
ignition switch is turned off, when the
ignition switch is turned back on, the
volume will come back to a ªnominalº
listening level. However, if the radio
power is turned off (with the
ªVOL/PUSH ONº button), the volume
will remain in the position it was set
at when radio power is switched back
on (digital systems only).
*
[AS10354( GV)04/95]
Selecting the AM or FM frequency band
*
[AS10355( GV)04/95]
Push the ªAM/FMº button to select the desired
frequency band. Pushing the ªAM/FMº button
causes the frequency band to switch from ªAMº
to ªFM1º to ªFM2º to ªAMº, changing one band
to the next each time the button is pressed.
These functions are used with the station
memory buttons described underHow to tune
radio stations.
%*
[AS10356( GV)05/95]
How to tune radio stations
*
[AS10357( GV)01/95]
There are four ways for you to tune in a
particular station. You can use the ªTUNEº,
ªSEEKº, ªSCANº or memory buttons.
File:rcasv.ex
Update:Thu Feb 15 08:03:35 1996

152
*
[AS10358( GV)05/95]
q
Using the ªTUNEº function
[AS10359( GV)03/95]
You can change the frequency up or down
one increment at a time by pressing and
releasing either the left
bor right
aside of
the ªTUNEº button. To change frequencies
quickly, press and hold down either the right
or left side of the ªTUNEº button.
*
[AS10360( GV)04/95]
Manual tuning adjusts your radio to any
allowable broadcast frequency, whether or
not a station is present on that frequency.
(SeeAll About Radio Frequenciesin this
section.)
*
[AS10361( GV)04/95]
q
Using the ªSEEKº function
*
[AS10362( GV)03/95]
Press the right
aside of the ªSEEKº button
to select the next listenable station up the
frequency band. Press the left
bside of the
button to select the next listenable station
down the frequency band. By holding the
button down, listenable stations can be
passed over to reach the desired station.
*
[AS10363( GV)01/95]
q
Using the ªSCANº function
*
[AS10364( GV)04/95]
Pressing the ªSCANº button will begin the
scan mode up the frequency band, stopping
on each listenable station for approximately
five seconds.
*
[AS10365( GV)02/95]
To stop the scan mode on the presently
sampled station, press the ªSCANº button
again.
*
[AS10366( GV)01/95]
q
Setting the station MEMORY PRESET buttons
*
[AS10367( GV)01/95]
Your radio is equipped with 6 station
memory buttons. These buttons can be used
to select up to 6 preset AM stations and 12
FM stations (6 in FM1 and 6 in FM2)
[AS10368( GV)05/95]
Follow the easy steps below to set these buttons
to the desired frequencies:
*
[AS10369( GV)04/95]
1. Select a band, then select a frequency.
File:rcasv.ex
Update:Thu Feb 15 08:03:35 1996