1996 FORD ASPIRE battery

20890ÊF (32ÊC) andmore often in temperatures
above90ÊF (32ÊC).Keep the electrolyte level in
each cell up to the level indicator. Do not
overfill.
[SV29630(ALL)04/95]
If the level gets low, you can add plain tap
water to the battery, provided the water isn't
hard or doesn't have a high mineral or alkali
content. However, if possible, refill with distilled
water. If the battery needs water quite often,
have the charging system checked for a possible
malfunction.
*
[SV29635(ALL)03/95]
Help Us Protect Our Environment
*
[SV29640(ALL)04/95]
Ford Motor Company strongly recommends that
used lead-acid batteries be returned to an
authorized recycling facility for disposal.
*
[SV29645(ALL)03/95]
one inch art:0000983-A
Battery recycling symbol
*
[SV29650(ALL)02/95]
RWARNING
The gases around the battery can explode
if exposed to flames, sparks, or lit
cigarettes. An explosion could result in
injury or vehicle damage.
*
[SV29660(ALL)02/95]
RWARNING
To protect yourself when charging a
battery, always shield your face and eyes.
Make sure that you can breathe fresh air.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

209 %
*
[SV29665(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns
skin, eyes, and clothing.
*
[SV29670(ALL)07/95]
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water
for at least 15 minutes. If someone swallows the
acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or
vegetable oil. Call a doctor immediately.
%*
[SV29675(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns
skin, eyes, and clothing.
%*
[SV29690(ALL)06/95]
RWARNING
Applying too much pressure on the ends
when lifting a battery could cause acid to
spill. Lift the battery with a carrier or
with your hands on the opposite corners.
*
[SV29700(ALL)03/01]
Automatic Transaxle Fluid
*
[SV29800(ALL)03/95]
Under normal circumstances, you do not need to
check the fluid level of the transaxle, since your
vehicle does not use up transaxle fluid. Refer to
theMaintenance Schedule and Recordbooklet for
replacement intervals. However, if the transaxle
is not working properly Ð for instance, the
transaxle may slip or shift slowly, or you may
notice some sign of fluid leakage Ð the fluid
level should be checked.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

216 [SV34500(ALL)07/93]The following charts tell you which fuses protect
each electrical part of your vehicle. If a fuse
blows, all the parts of your car that use the
circuit will not work.
[SV34600(ALL)02/95]
Once you have determined which fuses to check,
follow the procedures underChecking and
replacing fuseslater in this chapter.
[SV35370(ALL)09/93]
Your Aspire has a main fuse block under the
hood and a regular fuse box mounted in the
instrument panel behind a cover.
[SV35390(ALL)05/93]
Main fuse block
[SV35420(ALL)03/94]
If the 80 Amp. fuse is blown, it must be
replaced. To remove the main fuse block and
replace the fuse:
[SV35430(ALL)07/95]
one third page art:0032220-B
Main fuse block location
[SV35440(ALL)05/93]
1. Disconnect the negative battery cable.
[SV35460(ALL)05/93]
2. Remove the nuts on either end.
[SV35480(ALL)05/93]
3. Lift the fuse block and open the flaps on the
side of the fuse block.
[SV35520(ALL)05/93]
4. Remove the bolts on either side of the block.
[SV35540(ALL)05/93]
5. Replace the fuse with a new one of the same
rating.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

217 [SV35550(ALL)07/93]
one third page art:0032234-B
Removing fuse block
[SV35560(ALL)05/93]
To install the fuse block:
[SV35580(ALL)05/93]
1. Place the fuse block cover back in position
and fasten the bolts on both sides.
[SV35620(ALL)05/93]
2. Attach the nuts on both ends of the fuse
block.
[SV35640(ALL)05/93]
3. Connect the negative battery cable.
[SV35680(ALL)07/93]
quarter page art:0032229-A
Main fuse block
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

227
*
[SV41500(ALL)03/95]
Installing the headlamp bulb
[SV41600(ALL)07/93]
1. Insert the glass end of the bulb assembly
into the socket.
[SV41650(ALL)05/93]
2. Secure the bulb assembly in place with the
metal retaining clip.
[SV41675(ALL)05/93]
3. Attach the rubber boot over the bulb
assembly.
[SV41700(ALL)05/93]
4. Slip the bulb retaining ring over the boot
and bulb assembly. Lock the ring into the
socket by rotating it clockwise until you feel
a ªstopº.
[SV41800(ALL)05/93]
5. Push the electrical connector into the rear of
the bulb assembly until it locks into position.
[SV41900(ALL)02/95]
6. Turn the headlamps on and make sure they
work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
*
[SV42000(ALL)02/95]
High-Mount Brakelamp Bulbs
[SV42100(ALL)02/95]
To replace the high-mount brakelamp bulb, refer
to the instructions below or take your vehicle to
your Ford dealer or a qualified technician.
[SV42200(ALL)05/94]
To remove the high-mount brakelamp:
[SV42300(ALL)05/93]
1. Disconnect the negative battery cable.
[SV42400(ALL)05/94]
2. Raise the hatchback.
[SV42450(ALL)05/94]
3. Use a Phillips screwdriver to remove three
attaching screws from the rear wiper motor
cover (if equipped). Lay the cover aside.
[SV42600(ALL)05/94]
4. Gently pull the hatchback trim panel away
from the hatchback.
[SV42700(ALL)05/94]
5. Disconnect the luggage compartment lamp
electrical connector (if equipped) and lay the
trim panel aside.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

228 [SV42800(ALL)05/94]6. Rotate the high-mount lamp socket
counterclockwise and remove it from the
housing.
[SV42900(ALL)05/94]
7. Carefully remove the bulb by gently pulling
it straight from the socket.
*
[SV43000(ALL)03/95]
To install a bulb:
[SV43100(ALL)05/94]
1. Firmly install the replacement bulb into the
socket.
[SV43200(ALL)05/94]
2. Place the socket assembly in the high-mount
stoplamp housing and turn clockwise to lock
into position.
[SV43300(ALL)05/94]
3. Position the hatchback trim panel and
connect the luggage compartment lamp
electrical connector (if equipped).
[SV43400(ALL)05/94]
4. Insert the trim panel retaining clips into the
locating holes in the hatchback and push
each clip firmly into position.
[SV43500(ALL)05/94]
5. Install the rear wiper motor cover (if
equipped).
[SV43600(ALL)05/94]
6. Close the hatchback and reconnect the
negative battery cable.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

232
*
[SV48700(ALL)02/92]
Never use a metal exhaust collector when you
service your vehicle. If the metal collector
contacts any of your vehicle's plastic trim or
bumper parts they could melt or deform.
*
[SV48800(ALL)01/95]
Do not drive your vehicle if it does not operate
properly. See your dealer if the engine runs on
for more than five seconds after you shut it off
or if it misfires, surges, stalls, or backfires.
%*
[SV48900(ALL)05/95]
Information about your vehicle's emission
control system is on the Vehicle Emission
Control Information decal located on or near the
engine. This decal identifies engine displacement
and gives some tune-up specifications.
%*
[SV48910(ALL)07/95]
Readiness for Inspection/Maintenance
Testing
*
[SV48920(ALL)07/95]
In some localities it may become a legal
requirement to pass an Inspection/
Maintenance (I/M) test of the On-Board
Diagnostic (OBD) II system. If the vehicle's
powertrain system or its battery has just been
serviced, the OBD II system is reset to a not
ready for I/M testing condition. To prepare for
I/M testing, the law specifies a ªneed for
additional mixed city and highway driving to
complete the checkº of the OBD II system. As
soon as all of the OBD II system checks are
successfully completed, the OBD II system is set
to the ready condition. The amount of driving
required to reach the ready condition varies with
individual driving patterns. To complete this
requirement in the minimum amount of time,
refer to the OBD II Drive Cycle defined below. If
the vehicle owner cannot or does not want to do
the additional driving required by law, a service
center can perform this drive cycle as it would
any other type of repair work.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

239 %
*
[SV52200(ALL)01/95]
Engine
*
[SV52300(ALL)01/95]
q
Start engine every 15 days. Run at fast idle
until it reaches normal operating temperature.
*
[SV52400(ALL)01/95]
q
With your foot on the brake, shift through all
the gears while the engine is running.
%*
[SV52500(ALL)01/95]
Fuel system
%*
[SV52600(ALL)07/94]
q
Fill fuel tank with high-quality unleaded fuel
until the first automatic shutoff of the fuel
pump nozzle.
*
[SV52800(ALL)03/95]
NOTE: During extended periods of vehicle
storage (60 days or more), fuel may
deteriorate due to oxidation. This can
damage rubber and other polymers in
the fuel system and may also clog
small orifices.
*
[SV52900(ALL)01/95]
Ford Gas Stabilizer should be added whenever
actual or expected storage periods exceed 60
days. Follow the instructions on the label. The
vehicle should then be operated at idle speed to
circulate the additive throughout the fuel system.
*
[SV53000(ALL)01/95]
A volatile corrosion inhibitor added to the fuel
system will protect the fuel system's inner
surfaces from corrosion. Follow the instructions
packaged with the product.
%*
[SV53100(ALL)01/95]
Cooling system
*
[SV53200(ALL)01/95]
q
Protect against freezing temperatures.
%*
[SV53300(ALL)01/95]
Battery
*
[SV53400(ALL)01/95]
q
Check and recharge as necessary.
*
[SV53500(ALL)01/95]
q
Keep connections clean and covered with a
light coat of grease.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996