1996 FORD ASPIRE heater

51 %
*
[ST08700(ALL)06/95]
Using the Engine Block Heater
(If equipped)
*
[ST08900(ALL)03/95]
Engine block heaters are strongly recommended
if you live in a region where temperatures reach
-10ÊF (-23ÊC) orbelow. An engine block heater
warms the engine coolant, which improves
starting, warms up the engine faster, and allows
the heater-defrost system to respond quickly.
*
[ST09100(ALL)02/95]
To turn the heater on, simply plug it into a
grounded 110-volt outlet. Ford recommends that
you use a 110-volt circuit that is protected by a
ground fault circuit interrupter.
*
[ST09200(ALL)05/95]
RWARNING
To prevent electrical shock, do not use
your heater with ungrounded electrical
systems or two-pronged (cheater) adapters.
*
[ST09300(ALL)03/95]
For best results, plug the heater in at least three
hours before you start your vehicle. Using the
heater for longer than three hours will not
damage the engine, so you can plug it in at
night to start your vehicle the following
morning.
*
[ST09400(ALL)03/95]
If the Engine Cranks but Does
Not Start or Does Not Start After
a Collision
*
[ST09450(ALL)07/95]
Fuel Pump Shut-Off Switch
*
[ST09460(ALL)10/95]
If the engine cranks but does not start or does
not start after a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device intended to stop the fuel
pump when your vehicle has been involved in a
major jolt.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996

54
*
[ST12000(ALL)05/95]
RWARNING
If you smell exhaust fumes inside your
vehicle, have your dealer inspect your
vehicle immediately. Do not drive if you
smell exhaust fumes.
*
[ST12100(ALL)01/95]
Have the exhaust and body ventilation systems
checked whenever:
*
[ST12200(ALL)02/95]
q
your vehicle is raised for service
*
[ST12300(ALL)02/95]
q
the sound of the exhaust system changes
*
[ST12400(ALL)01/95]
q
your vehicle has been damaged in a collision
*
[ST12500(ALL)01/95]
Improve your ventilation by keeping all air inlet
vents clear of snow, leaves, and other debris.
[ST12600(ALL)02/95]
If you must allow your engine to idle for long
periods of time, be sure you are in an open area
and open the windows at least one inch
(25 mm). Also, adjust the heating or air
conditioning to bring in outside air.
[ST12700(ALL)02/95]
If you are using the heater, set the fan speed on
1, 2, or 3 with the function lever on the position
of your choice and the air door control lever in
the fresh (outside air) position.
[ST12900(ALL)02/95]
If you are using the air conditioner, set the fan
speed on 1, 2, or 3 with the function lever in the
position of your choice. Set the air door control
lever in the fresh (outside air) position.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996

69
*
[IP00900(ALL)06/95]
The Climate Control Systems
*
[IP01000(ALL)02/91]
Heating Only System (Without Air
Conditioning)
[IP01100(ALL)01/92]
Function selector
[IP01200(ALL)07/95]
The heater controls in your car use levers to
control air direction and temperature. Fan speed
is controlled by a separate knob in the control
panel. The function selector lever lets you
control the direction of airflow.
[IP01500(ALL)07/95]
half page art:0032166-B
Heating only system control panel
[IP01600(ALL)05/93]
The symbols above the function selector lever
tell you where the air is being directed when the
lever is set to that position on the heater control
panel.
File:06icipf.ex
Update:Wed Jan 24 14:47:07 1996

74
*
[IP06600(ALL)06/93]
Air Conditioning System (If equipped)
[IP06700(ALL)08/91]
Air distribution is controlled the same way as in
the heater system described above.
[IP06800(ALL)02/92]
The air conditioner switch is located on the
climate control panel. To turn on the air
conditioner, push the A/C button. An indicator
light will come on. To turn off the air
conditioner, push the button again. The fan must
also be on for the A/C to operate.
[IP07100(ALL)09/93]
one third page art:0032165-C
Air conditioning system control panel
[IP07200(ALL)08/91]
To get maximum cooling from the air
conditioner:
[IP07225(ALL)07/95]
1. Move the function selector lever to theQ
(panel) position.
[IP07250(ALL)08/91]
2. Set the temperature control lever all the way
to the blue area.
[IP07275(ALL)07/95]
3. Close the air door by moving the air door
control lever to theM(recirculate)
position.
[IP07300(ALL)08/91]
4. Push the A/C button.
[IP07325(ALL)07/95]
5. Set the
Hspeed on its highest setting.
File:06icipf.ex
Update:Wed Jan 24 14:47:07 1996

139
*
[RE01700(ALL)03/95]
4. Check all battery terminals and remove any
excessive corrosion before you attach the
jumper cables.
*
[RE01800(ALL)03/95]
5. Turn on the heater fan in both vehicles.
Press the DEFROST button. Turn off all
other switches and gauges.
%*
[RE01900(ALL)05/95]
Connecting the jumper cables
*
[RE02000(ALL)03/95]
1. Connect one end of the first jumper cable to
the positive (+) terminal of the discharged
battery. (You can connect either jumper cable
to the positive (+) terminal, as long as you
use the same cable for both positive
terminals.) Most jumper cables have a red
cable and a black cable. The red cable is
generally used for the positive terminals and
the black for the negative ones.
*
[RE02100(ALL)04/95]
2. Connect the other end of the first cable to
the positive (+) terminal of the booster
battery.
*
[RE02200(ALL)07/95]
3. Connect one end of the second cable to the
negative (S) terminal of the booster battery
Ð NOT to the discharged battery.
*
[RE02300(ALL)03/95]
4. Connect the other end of that cable to a
good metallic surface on the engine or frame
of the disabled vehicle. The following
illustration shows where you can find a
metallic surface.
*
[RE02400(ALL)07/95]
RWARNING
Do not connect the end of the second
cable to the negative (S) terminal of the
battery to be jumped. A spark may cause
an explosion of the gases that surround
the battery.
File:12icref.ex
Update:Wed Jan 24 14:52:09 1996

195
*
[SV21400(ALL)02/95]
Engine coolant refill procedure
*
[SV21500(ALL)03/95]
When the entire engine cooling system is to be
drained and refilled, use the following
procedure:
*
[SV21600(ALL)01/89]
1. Remove the radiator cap.
*
[SV21700(ALL)06/89]
2. With the engine off and cool, add a 50/50
mixture of recommended engine cooling
system fluid and water until the radiator is
full.
*
[SV21800(ALL)07/93]
3. Replace and fully tighten the radiator cap,
then unscrew the cap to the first stop.
*
[SV21900(ALL)06/89]
4. Start and idle the engine until the radiator
upper hose is warm (this indicates the
thermostat is open and engine coolant is
flowing through the entire system).
[SV22000(ALL)03/94]
5. When you are done, stop the engine and
tighten the cap completely.
%*
[SV22100(ALL)11/94]
Checking hoses
*
[SV22200(ALL)01/89]
Check all engine and heater system hoses and
hose connections for deterioration, leaks, and
loose hose clamps as specified in the
maintenance schedule. Repair or replace with
Motorcraft hoses or equivalent as necessary.
*
[SV22300(ALL)03/95]
Windshield Washer Fluid and
Wipers
*
[SV22350(ALL)03/95]
Washer Fluid
*
[SV22500(ALL)01/95]
Check the level of the windshield washer fluid
every time you stop for fuel. The reservoir for
the windshield washer fluid is located in the
engine compartment.
[SV22600(ALL)05/93]
To check the washer fluid level, place your
finger over the hole in the reservoir cap and pull
out the dipstick.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

223 [SV37600(ALL)05/93]
Circuit Breaker
[SV37700(ALL)05/93]
The climate control systems require high
amperage. If the rated amperage is exceeded, a
protective circuit breaker will open.
[SV37800(ALL)07/93]
If the circuit is broken by the circuit breaker,
turn all heater and air-conditioner switches off
and restore the circuit by pushing the reset
button located in the interior fuse panel. If the
circuit breaks again, have it inspected by your
dealer.
[SV37900(ALL)07/93]
one third page art:0032233-B
Reset button for circuit breaker
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996