66 %
*
[ST06625(ALL)01/95]
NOTE: Your vehicle is equipped with a
brake-shift interlock feature. This
feature prevents you from shifting
from P (Park) unless you have the
brake pedal depressed. (The ignition
must be in the ON position.) If you
cannot shift from P (Park) with the
brake pedal depressed:
*
[ST06627(ALL)01/95]
1. Apply the parking brake.
*
[ST06629(ALL)01/95]
2. Remove the key.
*
[ST06631(ALL)08/95]
3. Insert the key and rotate it one position
clockwise (ignition in the OFF position).
*
[ST06633(ALL)08/95]
4. Apply the brake pedal and shift to N
(Neutral). (If the vehicle is shifted back to P
[Park], you must repeat the previous steps.)
*
[ST06635(ALL)01/95]
5. Start the vehicle.
*
[ST06637(ALL)07/95]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Aerostar
in this Owner Guide for instructions on checking
and replacing fuses.
*
[ST06640(ALL)05/95]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995
123
*
[FV04301(ALL)01/89]
Liftgate opening procedure
[FV04401(ALL)07/95]
1. Insert the key into the lock and turn it
counterclockwise. You can also unlock the
latch (but not release it) with the power door
lock system (if equipped).
*
[FV04500(ALL)01/89]
2. Reach under the license plate light shield
and release the liftgate latch by squeezing
the paddle handle rearward.
[FV04600(ALL)03/94]
3. To make the gate swing up to the fully
opened position, pull back and upward on
the latch paddle handle.
[FV04800(ALL)10/90]
one third page art:0020190-B
Opening the liftgate
*
[FV05300(ALL)10/89]
Make certain that you close the liftgate door and
window before driving your vehicle. If you do
not, possible damage may occur to the liftgate
door lift cylinders and attaching hardware.
*
[FV05400(ALL)08/95]
RWARNING
When driving your vehicle make sure that
the liftgate door and window are closed to
prevent exhaust fumes from being drawn
into the vehicle. This will also prevent
cargo from falling out.
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995
124
*
[FV05500(ALL)01/89]
Liftgate closing procedure
*
[FV05600(ALL)01/89]
1. To make the liftgate swing downward, reach
up and pull the lower edge of the liftgate (or
the loop handle on the inner trim panel of
vehicles with this option) and pull
downward.
*
[FV05700(ALL)01/89]
2. When you have pulled down the liftgate
enough so that you can reach the license
plate light shield, push the shield down and
forward to close the latch and liftgate. At
this point, the latch is not locked.
[FV05800(ALL)07/95]
3. You can lock the liftgate latch by pushing
down the lock button before you pull down
and close the liftgate. You can also lock the
liftgate latch by inserting your vehicle's door
key and turning it clockwise after you have
closed the liftgate, or by using the power
door locks (if equipped).
*
[FV05900(ALL)12/93]
The liftgate area is only intended for cargo, not
passengers. You can open and close the liftgate
from outside the vehicle. It cannot be opened
from inside the cargo area.
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995
152
*
[AS01100(ALL)08/95]
q
Using the ªSCAN/TUNEº button to scan
radio stations
[AS01150(ALL)08/95]
Pressing the ªSCAN/TUNEº button once
enters the scan mode (display will indicate
ªSCNº). Pushing the top (
a) half of the
ªSEEKº button will begin the scan mode up
the frequency band, stopping on each
listenable station for approximately five
seconds. Pushing the bottom (
b) half of the
ªSEEKº button will begin the scan mode
down the frequency band, again stopping on
each listenable station for approximately five
seconds.
*
[AS01200(ALL)08/95]
To stop the scan mode on the presently
sampled station press the ªSCAN/TUNEº
button again.
*
[AS01250(ALL)08/95]
q
Setting the Station Memory Preset buttons
%*
[AS01300(ALL)08/95]
Your radio is equipped with 5 station
memory buttons. These buttons can be used
to select up to 5 preset AM stations and 10
FM stations (5 in FM1 and 5 in FM2). Follow
the easy steps below to set these buttons to
the desired frequencies.
*
[AS01350(ALL)08/95]
1. Select a band, then select a frequency.
*
[AS01400(ALL)08/95]
2. Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now held in memory on that
button.
*
[AS01450(ALL)08/95]
3. Follow the two steps above for each station
memory preset button you want to set.
*
[AS01500(ALL)08/95]
NOTE: If the vehicle's battery is disconnected,
the clock and station memory preset
buttons (if programmed in auto mode)
will need to be reset.
File:09cpasa.ex
Update:Tue Aug 29 17:42:51 1995
155
*
[AS02200(ALL)08/95]
q
Adjusting speaker fader
*
[AS02250(ALL)08/95]
Fade control allows you to adjust the sound
distribution between the front and rear
speakers. Push the ªAUDIOº button
repeatedly until the display reads ªFADE.º
Push the ª+º side of the ªVOLº button to
shift the sound to the front speakers, and
push the ª-º side to shift the sound to the
rear speakers.
*
[AS02275(ALL)08/95]
NOTE: Illuminated bars in the display show
relative levels of bass and treble and
positions of speaker balance and fader
functions after adjustments are made,
then revert to volume level set.
%*
[AS02300(ALL)08/95]
Clock operation
[AS02325(ALL)08/95]
When in the radio mode, push the ªCLOCKº
button to switch from radio frequency to clock.
Only the clock numerals will be displayed in the
clock mode Ð there is no AM/PM indication.
When in the clock mode, the time will be
displayed until the button is pushed again.
However, if you retune the radio while it is in
the clock mode, the new radio frequency will be
displayed for approximately ten seconds and
then change back to clock display.
*
[AS02350(ALL)08/95]
When in the CD mode, push the ªCLOCKº
button to change the display from elapsed time
mode to track number mode to clock mode. If
the CD track selection is changed when you are
in the clock or elapsed time mode, the new track
number will be displayed for approximately ten
seconds and then revert back to the previous
mode.
*
[AS02375(ALL)08/95]
The clock can also be viewed with the ignition
off. Push the ªCLOCKº button and the time will
be displayed momentarily.
File:09cpasa.ex
Update:Tue Aug 29 17:42:51 1995
156
*
[AS02400(ALL)08/95]
To set the clock, simultaneously press the
ªCLOCKº button and either the bottom (
b) half
of the ªSEEKº button to set hours, or the top
(
a) half of the ªSEEKº button to set minutes.
%*
[AS02425(ALL)08/95]
Using the Controls on Your New Compact
Disc Player
*
[AS02450(ALL)08/95]
Your new Ford Compact Disc Player is capable
of playing 12 cmor8 cm discs, without an
adapter. The Player operates when the power is
on and a disc is inserted (label side up). Handle
the disc by its edge only. (Be sure to read and
follow all of the care and cleaning instructions
underHow To Take Care of and Clean Your CD
Player and Discs.)
*
[AS02475(ALL)08/95]
NOTE: If after you insert a disc, the disc is
ejected and ªERRORº begins scrolling
in the display, remove the disc and
reinsert it right side up (label side up).
*
[AS02500(ALL)08/95]
The digital display on your CD player will
either show the track (selection) number or the
elapsed time. (The display mode can be selected
by pressing the ªCLOCKº button.) Indicators for
play (
a), stop (
X) and compression on (ªCº)
are also in the display. (These features are
described later.)
*
[AS02525(ALL)08/95]
Once a disc is inserted, operation of the CD
player will override that of the radio.
[AS02550(ALL)08/95]
NOTE: The volume, bass, treble, balance and
fader controls on the radio are also
used with the CD player. Refer to
earlier operating instructions about
these controls.
File:09cpasa.ex
Update:Tue Aug 29 17:42:51 1995
171
*
[AS05325(ALL)08/95]
How to eject the tape
*
[AS05350(ALL)08/95]
To stop the tape and eject the cassette, press the
ªEJCTº button. The radio will resume playing if
the radio power is on. The tape cartridge can be
ejected with radio power (and/or ignition) on or
off.
*
[AS05375(ALL)08/95]
How to store the tape
*
[AS05400(ALL)08/95]
Press the ªAM/FMº button to stop the tape
player and resume radio play. The cassette will
be stored in the tape player and the
Xsymbol
in the display will be lit until you push the
ªPLAY PROGº button to resume tape play. Fast
forward and fast rewind can be used while the
tape is in storage mode without interrupting
radio play.
*
[AS05425(ALL)08/95]
Using the DolbyHB noise reduction feature
*
[AS05450(ALL)08/95]
NOTE: Noise reduction system manufactured
under license from Dolby Labs
Licensing Corporation. ªDolbyº and
double-D symbol are trademarks of
Dolby Laboratories Licensing
Corporation.
*
[AS05475(ALL)08/95]
Push thekbutton to activate. When on, the
ksymbol above the button will be lit.
%*
[AS05500(ALL)08/95]
Clock Operation
*
[AS05525(ALL)08/95]
How to view the clock mode
*
[AS05550(ALL)08/95]
Press the ªCLOCKº button to alternate the
frequency and time in the display. In the clock
mode, pressing any radio function will
automatically display the radio frequency for
approximately ten seconds before changing back
to the clock mode.
File:09cpasa.ex
Update:Tue Aug 29 17:42:51 1995
172
*
[AS05575(ALL)08/95]
How to set the clock
*
[AS05600(ALL)08/95]
1. Turn the radio on.
*
[AS05625(ALL)08/95]
2. Press and hold in the ªCLOCKº button,
press the ªSEEKº button left (
b) to advance
the hours and right (
a) to advance the
minutes.
*
[AS05650(ALL)08/95]
NOTE: The clock displays 12-hour time with
no AM/PM indications.
*
[AS05675(ALL)08/95]
NOTE: On the High-Level Audio System, the
clock can be set with the radio power
on or off.
*
[AS05700(ALL)08/95]
Tape error messages
*
[AS05725(ALL)08/95]
Your cassette tape player is equipped to
diagnose certain problems you may experience.
Error codes are as follows:
*
[AS05750(ALL)08/95]
Error 0Ð Communication error between the
radio controller and the tape controller. The
cassette player will eject the tape. Insert the tape
again. If the same error code appears, turn the
ignition off, then back on again and insert the
tape.
*
[AS05775(ALL)08/95]
Error 1Ð Possible problem cartridge. The
cassette tape player will eject the tape. Insert the
tape again. If the same error code appears in the
display, try a different cartridge.
*
[AS05800(ALL)08/95]
Error 2Ð Tape eject or load failure. Your
cassette tape player will go into the pause mode.
Push ªEJCTº to eject the tape. If the tape doesn't
eject, refer the problem to qualified personnel for
service.
File:09cpasa.ex
Update:Tue Aug 29 17:42:51 1995