1996 CHRYSLER VOYAGER wiper fluid

CAUTION: When installing the primary and second-
ary brake tubes on master cylinder, be sure brake
tubes do not contact any other components within
the vehicle and that there is slack in the flexible
sections of the tubes. This is required due to the
movement between the ABS hydraulic control mod-
ule (HCU) and the master cylinder, when the vehicle
is in motion.
(4) Connect the primary and secondary brake
tubes to master cylinder primary and secondary
ports (Fig. 99). Brake tubes must be held securely
when tightened to control orientation of flex section.
Then fully tighten the tube nuts to a torque of 17
N´m (145 in. lbs.).
(5) Install the vehicle wiring harness connector, on
the brake fluid level sensor in the master cylinder
brake fluid reservoir (Fig. 98).
(6) Install filler tube into the master cylinder fluid
reservoir (Fig. 97).
VACUUM BOOSTER 2.4 LITER ENGINE
REMOVE
CAUTION: Reserve vacuum in the vacuum booster
must be pumped down (removed) before removing
master cylinder from vacuum booster. This is nec-
essary to prevent the vacuum booster from sucking
in any contamination as the master cylinder is
removed. This can be done simply by pumping the
brake pedal, with the vehicle's engine not running,
until a firm feeling brake pedal is achieved.
(1) With engine not running, pump brake pedal
until a firm pedal is achieved (4-5 strokes).
(2) Remove both battery cables from battery.
(3) Remove the battery thermal guard and the bat-
tery from the battery tray.
(4) Remove the air inlet resonator and hoses as an
assembly from the throttle body and air cleaner
housing (Fig. 104)
(5) If vehicle is equipped with speed control,
unplug wiring harness connector from the speed con-
trol servo. Then disconnect vacuum lines from the
speed control servo and vacuum reservoir on battery
tray.
(6) Remove bolt attaching the speed control servo
bracket to the battery tray. Slide the bracket forward
to unhook it from the battery tray and remove.
(7) Remove the 2 bolts and the nut (Fig. 105)
attaching the battery tray to the body.
(8) Remove wiring harness connector from brake
fluid level sensor in master cylinder fluid reservoir
(Fig. 106).
(9) Clean the area where the master cylinder
assembly attaches to the power brake booster. Useonly a solvent such as Mopar Brake Parts Cleaner or
an equivalent.
(10) Remove clip attaching drain hose for wiper
module to brake tube at master cylinder. Remove
Fig. 104 Air Inlet Resonator
Fig. 105 Battery Tray Mounting Locations
Fig. 106 Fluid Level Sensor Electrical Connection
NSBRAKES 5 - 47
REMOVAL AND INSTALLATION (Continued)

(7) Install aNEWvacuum seal on mounting flange
of master cylinder (Fig. 110).
(8) Position master cylinder on studs of vacuum
booster aligning push rod on vacuum booster with
master cylinder piston.
(9) Install the 2 nuts (Fig. 107) mounting the mas-
ter cylinder to the vacuum booster. Tighten the
mounting nuts to a torque of 25 N´m (225 in. lbs.).
(10) Install the wiper module drain hose (Fig. 107)
on the wiper module. Install the tie strap attaching
the wiper module drain hose to the brake tube at the
master cylinder.Tie strap should be loosely tight-
ened so as not to collapse the wiper module
drain hose.
(11) Install the wiring harness connector on the
brake fluid level sensor in the master cylinder fluid
reservoir (Fig. 106).
(12) Install the battery tray in the vehicle. Install
the 2 bolts and the nut (Fig. 105) attaching the bat-
tery tray. Tighten the 2 bolts and the nut to a torque
of 14 N´m (125 in lbs.).(13) If vehicle is equipped with speed control,
install the speed control servo and bracket on the
battery tray. Install and securely tighten bolt attach-
ing bracket to battery tray.
(14) If vehicle is equipped with speed control,
install the wiring harness connector on the speed
control servo. Then connect the vacuum lines onto
the speed control servo and vacuum reservoir on bat-
tery tray.
(15) Install the air inlet resonator and hoses as an
assembly on the throttle body and air cleaner hous-
ing (Fig. 104). Securely tighten the hose clamp at the
air cleaner housing and throttle body.
(16) Install the battery and the battery thermal
guard.
(17) Install the battery cables on the battery.
(18) Check the operation of the stop lamp switch
and adjust if necessary.
VACUUM BOOSTER 3.0 LITER ENGINE
REMOVE
CAUTION: Stored vacuum in the vacuum booster
must be pumped down (removed) before removing
master cylinder from power brake booster. This is
necessary to prevent the power brake booster from
sucking in any contamination as the master cylin-
der is removed. This can be done simply by pump-
ing the brake pedal, with the vehicle's engine not
running, until a firm feeling brake pedal is achieved.
(1) With engine not running, pump the brake
pedal until a firm pedal is achieved (4-5 strokes).
(2) Remove both battery cables from battery.
(3) Remove the battery thermal guard and the bat-
tery from the battery tray.
(4) Remove the air inlet resonator and hoses as an
assembly from the throttle body and air cleaner
housing (Fig. 111)
(5) If vehicle is equipped with speed control,
unplug wiring harness connector from the speed con-
trol servo. Then disconnect vacuum lines from the
speed control servo and vacuum reservoir on battery
tray.
(6) Remove bolt attaching the speed control servo
bracket to the battery tray. Slide the bracket forward
to unhook it from the battery tray and remove.
(7) Remove the 2 bolts and the nut (Fig. 112)
attaching the battery tray to the body of the vehicle.
(8) Remove wiring harness connector from brake
fluid level sensor in master cylinder fluid reservoir
(Fig. 113).
(9) Clean the area where the master cylinder
assembly attaches to the power brake booster. Use
only a solvent such as Mopar Brake Parts Cleaner or
an equivalent.
Fig. 109 Retaining Clip Installed On Brake Pedal Pin
Fig. 110 Vacuum Seal Installed On Master Cylinder
NSBRAKES 5 - 49
REMOVAL AND INSTALLATION (Continued)

(10) Remove clip attaching drain hose to brake
tube at master cylinder. Remove drain hose (Fig. 114)
from wiper module. Remove the 2 nuts attaching the
master cylinder assembly to the power brake vacuum
booster (Fig. 114).
NOTE: It is not necessary to remove the brake
tubes from the master cylinder when removing the
master cylinder from the power brake vacuum
booster.
(11) Remove the master cylinder and the brake
tubes as an assembly from power brake vacuum
booster. When master cylinder is removed, lay it out
of the way on top of the left motor mount(12) Disconnect vacuum hose from check valve
located on power brake vacuum booster.DO NOT
REMOVE CHECK VALVE FROM POWER
BRAKE BOOSTER.
(13) Locate the power brake vacuum booster input
rod to brake pedal attachment under instrument
panel. Position a small screwdriver between the cen-
ter tang on the power brake booster input rod to
brake pedal pin retaining clip (Fig. 115).
(14) Rotate screwdriver enough to allow retaining
clip center tang to pass over end of brake pedal pin.
Then pull retaining clip off brake pedal pin.Discard
retaining clip. It is not to be reused. Replace
only with a new retaining clip when assembled.
(15) Remove the 4 nuts attaching the vacuum
booster to the dash panel. Nuts are accessible from
under dash panel in area of the steering column and
pedal bracket assembly.
(16) From outside the vehicle, slide power brake
vacuum booster forward until its mounting studs
Fig. 111 Air Inlet Resonator
Fig. 112 Battery Tray Mounting Locations
Fig. 113 Electrical Connection To Fluid Level Sensor
Fig. 114 Master Cylinder Attachment To Power
Brake Vacuum Booster
5 - 50 BRAKESNS
REMOVAL AND INSTALLATION (Continued)

only a solvent such as Mopar Brake Parts Cleaner or
an equivalent.
(13) Remove clip, attaching drain hose for wiper
module to brake tube at master cylinder. Remove
drain hose (Fig. 124) from wiper module. Remove the
2 nuts, attaching the master cylinder to the vacuum
booster (Fig. 124).
NOTE: It is not necessary to remove the brake
tubes from the master cylinder when removing the
master cylinder from the vacuum booster.
(14) Remove master cylinder and brake tubes as
an assembly from the vacuum booster. When mastercylinder is removed, lay it out of the way on top of
the left motor mount
Fig. 120 Electrical Connector At EGR Transducer
Fig. 121 Electrical And Vacuum Connections To
Throttle Body
Fig. 122 Throttle Body Attachment To Intake
Manifold
Fig. 123 Fluid Level Sensor Electrical Connection
Fig. 124 Master Cylinder Attachment To Vacuum
Booster
NSBRAKES 5 - 53
REMOVAL AND INSTALLATION (Continued)

CAUTION: The master cylinder is used to create
the seal for holding vacuum in the vacuum booster.
The vacuum seal on the master cylinder MUST be
replaced with a NEW seal whenever the master cyl-
inder is removed from the vacuum booster.
CAUTION: When removing the vacuum seal from
the master cylinder do not use a sharp tool.
(7) Using a soft tool such as a trim stick, remove
the vacuum seal from the master cylinder mounting
flange.
(8) Install aNEWvacuum seal on mounting flange
of the master cylinder (Fig. 128).
(9) Position master cylinder on studs of vacuum
booster, aligning push rod on vacuum booster with
master cylinder piston.
(10) Install the 2 nuts mounting the master cylin-
der to the vacuum booster (Fig. 124). Tighten both
mounting nuts to a torque of 25 N´m (225 in. lbs.).
(11) Install the wiper module drain hose (Fig. 124)
on the wiper module. Install the tie strap attaching
the wiper module drain hose to brake tube at the
master cylinder.Tie strap should be loosely tight-
ened so as not to collapse the wiper module
drain hose.
(12) Install the wiring harness connector on the
brake fluid level sensor in the master cylinder fluid
reservoir (Fig. 123).
(13) Install the throttle body and throttle cable
bracket on the intake manifold. Install the 2 bolts
(Fig. 122) attaching the throttle body to the intake
manifold and tighten to a torque of 25 N´m (225 in.
lbs.) Install clip (Fig. 122) attaching the wiring har-
ness to the throttle cable bracket.
(14) Install the wiring harness connectors on the
throttle position sensor and the AIS motor on throttle
body (Fig. 121).(15) Install the wiring harness connector (Fig. 120)
on the EGR valve transducer.
(16) Install the battery tray. Install the 2 bolts and
the nut (Fig. 119) attaching the battery tray to the
vehicle. Tighten the 2 bolts and the nut to a torque of
14 N´m (125 in lbs.).
(17) If vehicle is equipped with speed control,
install the speed control servo and bracket on the
battery tray. Install and securely tighten bolt attach-
ing bracket to battery tray.
(18) If vehicle is equipped with speed control,
install the wiring harness connector on the speed
control servo. Then connect the vacuum lines onto
the speed control servo and vacuum reservoir on bat-
tery tray.
(19) Install the air inlet resonator and hoses as an
assembly on the throttle body and air cleaner hous-
ing (Fig. 118). Securely tighten hose clamp at air
cleaner housing and throttle body.
(20) Install the battery and the battery thermal
guard.
(21) Install the battery cables on the battery.
(22) Check the operation of the stop lamp switch
and adjust if necessary.
JUNCTION BLOCK
REMOVE
(1) Using a brake pedal depressor, move and lock
the brake pedal to a position past its first 1 inch of
travel. This will prevent brake fluid from draining
out of the master cylinder when the brake tubes are
removed from the junction block.
(2) Raise vehicle on jackstands or centered on a
hoist. See Hoisting in the Lubrication And Mainte-
nance Group of this service manual.
CAUTION: Before removing the brake tubes from
the junction block, the junction block and the brake
tubes must be thoroughly cleaned. This is required
to prevent contamination from entering the brake
hudraulic system.
(3) Remove the 6 chassis brake tubes (Fig. 129)
from the junction block.
(4) Remove the bolt (Fig. 130) attaching the junc-
tion block mounting braket to the front suspension
cradle.
INSTALL
(1) Install the junction block and mounting bracket
(Fig. 130) on the front suspension cradle. Install the
attaching bolt and tighten to a torque of 28 N´m (250
in. lbs.).
(2) Install the 6 chassis brake tubes (Fig. 131) into
the inlet and outlet ports of the junction block.
Fig. 128 Vacuum Seal Installed On Master Cylinder
NSBRAKES 5 - 55
REMOVAL AND INSTALLATION (Continued)

MULTI-FUNCTION SWITCH
To test the windshield wiper and washer portion of
the multi-function switch:
(1) Remove the multi-function switch, refer to
removal procedures.
(2) Using an ohmmeter check continuity reading
between switch pins, refer to (Fig. 1) for proper pin
numbers.
REMOVAL AND INSTALLATION
MULTI-FUNCTION SWITCH
WARNING: BEFORE SERVICING A STEERING COL-
UMN EQUIPPED WITH AN AIRBAG REFER TO
GROUP 8M, RESTRAINT SYSTEMS FOR PROPER
AND SAFE SERVICE PROCEDURES.
REMOVAL
(1) Release hood latch and open hood.
(2) Disconnect and isolate battery negative cable.
(3) Remove upper and lower steering column
shrouds, refer to Group 19, Steering for proper pro-
cedures.
(4) Disconnect wire connector from back of turn
signal multi-function switch (Fig. 2).
(5) Remove screws holding turn signal switch to
steering column adapter collar.
(6) Remove turn signal switch.
INSTALLATION
For installation, reverse the above procedures. Ver-
ify switch operation by placing the control stalk ineither the right or left position and turning the steer-
ing wheel to ensure the automatic cancellation of the
switch.
WINDSHIELD WASHER BOTTLE
REMOVAL
(1) Hoist and support vehicle on safety stands.
(2) Remove right front wheel, refer to Group 22,
Wheels and Tires for proper procedures and tighten-
ing sequences.
(3) Remove front wheelhouse splash shield.
(4) Disconnect wire connectors from the windshield
and rear window washer pumps (Fig. 3).
(5) If washer bottle has fluid in it place a suitable
drain pan under the hose connections.
Fig. 1 Windshield Wiper and Washer±Multi-Function
Switch Test
Fig. 2 Turn Signal Multi-Function Switch
Fig. 3 Windshield Washer Bottle
8K - 4 WINDSHIELD WIPERS AND WASHERSNS
DIAGNOSIS AND TESTING (Continued)

Component Page
Fuel Tank Module...................8W-30, 45
Fuel Temperature Sensor.................8W-30
Fuel Timing Solenoid....................8W-30
Fuses (JB)............................8W-12
Fuses (PDC)...........................8W-10
Fusible Link.....................8W-20, 21, 63
Fusible Link A0........................8W-30
Fusible Link A11.......................8W-10
Fusible Link A54.......................8W-10
Grounds..............................8W-15
Generator.............................8W-20
Glove Box Lamp........................8W-44
Glow Plug Lamp.....................8W-30, 46
Glow Plugs............................8W-30
Glow Plug Relay........................8W-30
Headlamps............................8W-50
Headlamp Dimmer Switch..........8W-10, 46, 50
Headlamp Leveling Motors...............8W-50
Headlamp Switch.......................8W-50
Headlamp Washer......................8W-53
High Beam Indicator....................8W-46
High Beam Relay....................8W-10, 50
Headlamps............................8W-50
Horns................................8W-41
Hood Ajar Switch....................8W-39, 44
Horn Relay.........................8W-39, 41
Horn Switch.....................8W-10, 39, 41
HVAC Control.........................8W-42
Idle Air Control Motor...................8W-30
Ignition Coil Pack.......................8W-30
Ignition Switch.........................8W-10
Instrument Cluster.....................8W-40
Intake Air Temperature Sensor............8W-30
Intake Air Temperature/Manifold Absolute
Pressure Sensor.....................8W-30
Interior Lamps On Switch................8W-44
Junction Block.........................8W-12
Key-In Halo Lamp......................8W-44
Knock Sensor..........................8W-30
Lamp Assemblies.......................8W-51
License Lamp..........................8W-51
Liftgate Ajar Indicator Lamp..............8W-40
Liftgate Ajar Switch...............8W-39, 40, 44
Liftgate Arm/Disarm Switch............8W-39, 61
Liftgate Flood Lamps....................8W-44
Liftgate Lock Motor.....................8W-61
Low Beam Relay.....................8W-10, 50
Low Coolant Level Switch................8W-45
Low Fuel Warning Indicator Lamp..........8W-40
Low Oil Pressure Lamp..................8W-46
Low Washer Fluid Level Indicator Lamp.....8W-40
Low Washer Fluid Switch.................8W-53
Low/Reverse Pressure Switch..............8W-31
Low/Reverse Solenoid....................8W-31Component Page
Manifold Absolute Pressure Sensor.........8W-30
Memory Power Seat Switch...............8W-63
Seat Sensors...........................8W-63
Memory Seat/Mirror Module...........8W-62, 63
Memory Set Switch..................8W-62, 63
Message Center........................8W-46
Mid Reading Lamps.....................8W-44
Mode Door Actuator.....................8W-42
Name Brand Speaker Relay...............8W-47
Needle Movement Sensor.................8W-30
Odometer.............................8W-40
Output Shaft Speed Sensor...............8W-31
Overdrive Pressure Switch................8W-31
Overdrive Solenoid......................8W-31
Overhead Console.......................8W-49
Park Brake Switch...................8W-46, 50
Park Lamp Relay.........8W-10, 12, 44, 50, 51, 54
Park/Turn Signal Lamps.................8W-50
Airbag Squibs..........................8W-43
Power Distribution Center................8W-10
Power Folding Mirror Switch..............8W-62
Power Mirror Fold Relay.................8W-62
Power Mirror Switch....................8W-62
Power Mirror Unfold Relay...............8W-62
Power Seat Circuit Breaker............8W-62, 63
Powertrain Control Module...............8W-30
PTCs (JB).............................8W-12
Radiator Fan Disconnect.................8W-42
Radiator Fan Relays.....................8W-42
Radio................................8W-47
Radio Choke...........................8W-47
Reading Lamps........................8W-44
Rear A/C Heater Unit....................8W-42
Rear Blower Control Switches.............8W-42
Rear Cigar Lighter/Power Outlet...........8W-41
Rear Defogger On Indicator...............8W-42
Rear Dome Lamp.......................8W-44
Rear Fog Lamp.........................8W-51
Rear Fog Lamp Indicator.................8W-51
Rear Washer Motor.....................8W-53
Rear Washer Switch..................8W-42, 53
Rear Window Defogger...................8W-48
Rear Window Defogger Relay..............8W-48
Rear Window Defogger Switch..........8W-42, 48
Rear Wiper Delay On Indicator.........8W-42, 53
Rear Wiper Delay Switch..............8W-42, 53
Rear Wiper Motor.......................8W-53
Rear Wiper On Indicator..............8W-42, 53
Rear Wiper On Switch................8W-42, 53
Recirculate Mode Indicator................8W-42
Recirculate Mode Switch.................8W-42
Recirculation Door Actuator...............8W-42
Remote Keyless Entry Module.............8W-61
Repeater Lamps.....................8W-51, 52
8W - 02 - 2 8W - 02 COMPONENT INDEXNS/GS

8W-15 GROUND DISTRIBUTION
Component PageA/C Compressor Clutch....................8W-15-2, 3
A/C Heater Control........................8W-15-4
Airbag Control Module......................8W-15-4
All Wheel Drive Solenoid....................8W-15-13
Ash Receiver Lamp........................8W-15-6
Automatic Day/Night Mirror...................8W-15-5
AW4B13..............................8W-15-13
AWS1................................8W-15-13
Battery..............................8W-15-2, 3
Body Control Module.......................8W-15-6
Brake Pressure Switch......................8W-15-8
BS08.................................8W-15-5
BS31.................................8W-15-3
BS40.................................8W-15-3
BS41.................................8W-15-3
Center High Mounted Stop Lamp...............8W-15-14
Cigar/Accessory Relay.......................8W-15-7
Clockspring.............................8W-15-4
Clutch Switch............................8W-15-8
Combination Flasher/DRL Module...............8W-15-6
Controller Anti-Lock Brake....................8W-15-4
Crank Case Heater........................8W-15-3
CS06..............................8W-15-11, 12
Data Link Connector....................8W-15-2, 4, 12
Door Lock Relay..........................8W-15-6
Door Unlock Relay.........................8W-15-6
Downstream Heated Oxygen Sensor..............8W-15-5
Driver Door Arm/Disarm Switch.............8W-15-11, 12
Driver Door Courtesy Lamp...................8W-15-7
Driver Door Lock Switch..................8W-15-11, 12
Driver Door Unlock Relay....................8W-15-6
Driver Heated Seat Back.....................8W-15-9
Driver Heated Seat Cushion...................8W-15-9
Driver Heated Seat Module...................8W-15-9
Driver Heated Seat Switch....................8W-15-9
Driver Power Mirror........................8W-15-4
Driver Power Seat Switch....................8W-15-5
Driver Power Window Switch..................8W-15-7
DS01.................................8W-15-7
EC1C19...............................8W-15-5
Engine Speed Sensor.......................8W-15-3
ES01.................................8W-15-3
ES02.................................8W-15-3
ES11 .................................8W-15-2
ES12.................................8W-15-3
ES18.................................8W-15-2
ES23.................................8W-15-2
ES30.................................8W-15-3
ES31.................................8W-15-3
Front Blower Motor Relay....................8W-15-7
Front Cigar Lighter/Power Outlet...............8W-15-4
Fuel Heater.............................8W-15-3
Fuel Heater Relay.........................8W-15-3
Fuel Tank Module........................8W-15-13
G100................................8W-15-2, 3
G101.................................8W-15-2
G102................................8W-15-2, 3
G103................................8W-15-2, 3
G104.................................8W-15-4
G200.................................8W-15-4
G201.................................8W-15-4
G202.................................8W-15-5
G204.................................8W-15-4
G300...........................8W-15-5, 6, 7, 8, 9
G301............................8W-15-10, 11, 12
G302.................................8W-15-13
G400.................................8W-15-14
Headlamp Dimmer Switch....................8W-15-4
Headlamp Switch........................8W-15-4, 6
Headlamp Washer........................8W-15-10
High Note Horn.......................8W-15-11, 12
Hood Ajar Switch.........................8W-15-10
HS1..................................8W-15-9
HS3..................................8W-15-9
HS5D B09..............................8W-15-9
HS5P B56..............................8W-15-9
Ignition Switch.........................8W-15-4, 6
Instrument Cluster.......................8W-15-4, 6
Junction Block...........................8W-15-6
Key-In Halo Lamp.........................8W-15-6
Left Combination Relay.....................8W-15-13Component PageLeft Door Speaker.........................8W-15-5
Left Front Park/Turn Signal Lamp...............8W-15-7
Left Headlamp...........................8W-15-8
Left Headlamp Leveling Motor.................8W-15-8
Left High Headlamp........................8W-15-8
Left Liftgate Flood Lamp....................8W-15-14
Left Low Headlamp........................8W-15-8
Left Rear Door Ajar Switch...................8W-15-13
Left Rear Lamp Assembly....................8W-15-13
Left Rear Speaker.........................8W-15-5
Left Repeater Lamp........................8W-15-5
Left Speed Control Switch....................8W-15-4
Left Stop/Turn Signal Relay..................8W-15-13
License Lamp...........................8W-15-14
Liftgate Ajar Switch.......................8W-15-14
Liftgate Arm/Disarm Switch..................8W-15-14
Low Coolant Level Switch....................8W-15-3
Low Note Horn..........................8W-15-10
Low Washer Fluid Switch.................8W-15-11, 12
Memory Power Seat Switch..................8W-15-5, 9
Memory Seat/Mirror Module.................8W-15-5, 9
Memory Set Switch........................8W-15-7
Message Center...........................8W-15-6
Name Brand Speaker Relay...................8W-15-6
Needle Movement Sensor.....................8W-15-3
Overhead Console......................8W-15-11, 12
Passenger Door Arm/Disarm Switch.............8W-15-10
Passenger Door Courtesy Lamp.................8W-15-7
Passenger Door Lock Switch..................8W-15-10
Passenger Heated Seat Back...................8W-15-9
Passenger Heated Seat Cushion.................8W-15-9
Passenger Heated Seat Module.................8W-15-9
Passenger Heated Seat Switch.................8W-15-9
Passenger Power Mirror.....................8W-15-4
Passenger Power Seat Switch................8W-15-5, 12
Passenger Power Window Switch................8W-15-7
Power Distribution Center.................8W-15-2, 3, 7
Power Folding Mirror Switch..................8W-15-6
Power Mirror Switch.......................8W-15-6
Powertrain Control Module..................8W-15-2, 3
Radiator Fan Disconnect.....................8W-15-3
Radiator Fan No. 1........................8W-15-2
Radiator Fan No. 2........................8W-15-2
Radiator Fan Relay........................8W-15-2
Radiator Fan Relay No. 1.....................8W-15-3
Radio.................................8W-15-5
Rear Blower Front Control Switch...............8W-15-4
Rear Blower Rear Control Switch...............8W-15-13
Rear Cigar Lighter/Power Outlet...............8W-15-13
Rear Window Defogger.....................8W-15-14
Rear Wiper Motor.........................8W-15-14
Remote Keyless Entry Module..................8W-15-4
RF3E40...............................8W-15-2
RFS2.................................8W-15-2
Right Combination Relay....................8W-15-13
Right Door Speaker........................8W-15-5
Right Front Park/Turn Signal Lamp.............8W-15-10
Right Headlamp..........................8W-15-10
Right Headlamp Leveling Motor................8W-15-10
Right High Headlamp......................8W-15-10
Right Liftgate Flood Lamp...................8W-15-14
Right Low Headlamp......................8W-15-10
Right Rear Door Ajar Switch..................8W-15-13
Right Rear Lamp Assembly...................8W-15-13
Right Rear Speaker........................8W-15-5
Right Repeater Lamp......................8W-15-10
Right Speed Control Switch...................8W-15-4
Right Stop/Turn Signal Relay.................8W-15-13
Seat Belt Switch..........................8W-15-8
Sentry Key Immobilizer Module.................8W-15-4
Stop Lamp Switch.......................8W-15-6, 7
Traction Control Switch......................8W-15-6
Trailer Tow Connector......................8W-15-13
Transmission Control Module..................8W-15-2
Transmission Control Relay...................8W-15-2
Universal Garage Door Opener..............8W-15-11, 12
Upstream Heated Oxygen Sensor................8W-15-2
Vehicle Speed Control Servo...................8W-15-2
Wiper Module............................8W-15-5
Wiper On Relay...........................8W-15-7
NS/GS8W - 15 GROUND DISTRIBUTION 8W - 15 - 1