1996 CHEVROLET TRACKER light

NOTICE:
If your rear wheels can’t rotate, don’t try to
drive. This might happen if you were stuck in
very deep sand or mud or were
up against a solid
object.
You could damage your transmission.
Also, if
you stop when going uphill, don’t hold
your vehicle there with only the accelerator
pedal. This could overheat and damage the
transmission. Use your brakes to hold your
vehicle in position on
a hill.
Power Mode Selector Switch
A power mode selector
switch is included. When
you need more power for
climbing hills or quicker
acceleration, press the
P (POWER) switch. The
POWER indicator
light on the instrument panel
comes on. For normal driving, press the
N (NORMAL)
switch. The POWER indicator light goes off.
Overdrive Off Switch (Option)
The overdrive off switch is located on the left side of the
shifter. By operating the overdrive
off switch, the
four-speed automatic transmission (three-speed plus
overdrive) can be converted to a three-speed automatic
transmission. While in the three-speed mode, the
transmission will not shift into the overdrive position.
To convert the transmission to the three-speed mode,
push in the overdrive off switch and release
it. The
switch comes out and the
OD OFF indicator light on
the instrument panel comes on.
To return the transmission to the four-speed mode, push
in
the overdrive off switch again. The switch will remain
in and the
O/D OFF indicator light goes off.
Please note that if the transfer lever is in the 4L position,
the four-speed automatic transmission will remain in the
three-speed mode.
2-13
ProCarManuals.com

Automatic Transfer Case
With automatic freewheeling hubs, you don’t have to get
out &the vehicle to lock or unlock the hubs.
Locking the Hubs
1. Stop your vehicle.
2. Shift the transfer case to FOUR-WHEEL
HIGH (4H) or FOUR-WHEEL LOW (4L).
3, Drive slowly forward and the hubs will lock.
Unlocking the Hubs
1. Stop your vehicle.
2. Drive 7 feet (2 m) in the direction opposite to the
direction
you were driving before you stopped.
3. Then, press the clutch if you have a manual
transmission, and shift the transfer case to
TWO-WHEEL HIGH (2H). The hubs will unlock. The transfer case shift lever is on the floor to the right
of the driver. Use this lever to shift into and out of
four-wheel drive.
An indicator light comes on when the
transfer
case is in FOUR-WHEEL HIGH (4H) or
FOUR-WHEEL LOW (4L).
2-18
ProCarManuals.com

Parking Brake
To set the parking brake, hold the brake pedal down and
pull up
on the parking brake lever. If the ignition is on,
the brake system warning light will come on.
To release the parking brake, hold the brake pedal down.
Pull the parking brake lever up until
you can push in the
release button. Hold the release button in as you move
the lever all the way down.
2-20
ProCarManuals.com

Horn
The lever on the left side of the steering column
includes
your:
Turn Signal and Lane Change Indicator
Headlamp High/Low Beam Changer and Passing Signal
Lighting Operation
Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow
you to signal a turn
or a lane change.
To signal a tum, move the lever all the way up or down.
When the turn is finished, the lever will return automatically.
To sound the horn, press one of the horn symbols on
your steering wheel.
?ttm Signal/Multifunction Lever
An &ow on the instrument
panel will
flash in the direction
of the turn or lane change.
To signal a lane change, just
raise or lower the lever until
the arrow starts to flash.
Hold it there until you
complete your lane change.
The lever will return
by
itself when you release it.
As you signal a turn or a lane change, if the mows don’t
flash but just stay on, a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses and Circuit
Breakers” in
the Index) and for burned-out bulbs.
2-28
ProCarManuals.com

Lamps Control
Turn the outside part of the lever to control the lamps.
There are three positions for the lamp switch.
OFF: All lamps are off.
-300: : The parking lamps, taillamps, license plate
lamp and
the instrument panel lights come on. The
headlamps are off.
-:g- : The headlamps and all other operating lamps
come on.
Lamps On Reminder
If you turn the ignition off, remove the key, open the
door and leave the lamps
on, a chime will remind you to
turn off your lamps.
Headlamp High/Low Beam Changer
First, you must have the headlamps on. For high beams,
push the turn signal lever away
from you.
When the high beams are
on, a light on the instrument
panel also
will be on. It will
go off when you switch to
low beam.
To switch back to low beams, pull the lever toward you.
2-29
ProCarManuals.com

Flash-to-Pass
With the lever in the low-beam position, pull the lever
towad you to momentarily switch to high beam (to
signal that you are going to pass). When you release the
lever, the headlamps will return
to low-beam operation.
Windshield WipedWasher Lever
The lever on the right side of the steering column
controls the windshield wipers
and washers. Move the wiper switch
to the position
you want:
OFF: The wipers are off.
INT Intermittent wiper operation. In light rain or snow,
you might want to use this position rather than
continuous wiping.
LO: The wipers will run continuously at low speed.
HI: The wipers will run continuously at high speed.
For a single wiping cycle, pull the lever toward
you.
Hold it there until the wipers start, then let go. The
wipers will stop after one cycle. If you want more
cycles, hold the lever longer.
Be sure
to clear ice and snow from the wiper blades
before
using them. If they’re frozen to the windshield,
carefully loosen or thaw them.
If your blades do become
damaged, get new blades
or blade inserts.
Heavy snow or ice
can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice
to prevent an overload.
2-30
ProCarManuals.com

Setting Cruise Control 2. Get up to the speed you want.
A CAUTION: I
If you leave your cruise control switch on when
you’re not using cruise, you might hit a button and
go into cruise when you don’t want
to. You could
be startled and even lose control. Keep the cruise
control switch
OFF until you want to use it.
1. Press the
CRUISE Cm’L
switch on the
instrument panel
to turn the system
on. The indicator
light
on the switch
will come on.
3. Once you’re going 25 mph (40 km/h) or more, turn
the lever to COAST/SET and release. Your cruise
will set.
4. Take your foot off the accelerator pedal.
2-33
ProCarManuals.com

Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness
of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don't use cruise control on
steep hills.
Getting Out of Cruise Control
There are three ways to turn off cruise control:
Step lightly on the brake pedal, or push the clutch
pedal if you have a manual transmission.
Push in the CANCEL button on the end of the cruise
control lever.
0 Press OFF on the cruise control switch.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.
Lamps
Daytime Running Lamps
Daytime Running Laps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful
in the
short periods after dawn and before sunset.
The DRL system will make your low-beam headlamps
come on at a reduced brightness when:
0 The ignition is on,
0 The headlamp switch is off, and
The parking brake is released.
When you turn on the headlamp switch, your DRL will
go out, and your headlamps will come on.
The other lamps that come on
with your headlamps will
also come on.
When you turn off the headlamp switch, the regular
lamps will go
off, and your low-beam headlamps come
on at the reduced brightness of DRL.
To idle your vehicle with the DRL off, set the parking brake.
The
DRL will stay off until you release the parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need
it.
2-35
ProCarManuals.com