1996 CHEVROLET EXPRESS lock

Downloaded from www.Manualslib.com manuals search engine Then, without shutting off the engine, follow these steps:
1. Flip the handle up and then pull out the dipstick and
2. Push it back in all the way, wait three seconds and
wipe it
with a clean rag or paper towel.
then pull it back out again.
3.
4.
Check both sides of the dipstick, and read the lower
level. The fluid level must be in the
COLD area for a
cold check
or in the HOT area or cross-hatched area
for a hot check.
If the fluid level is in the acceptable range, push the
dipstick back in all
the way; then flip the handle
down
to lock the dipstick in place.
6-18

Downloaded from www.Manualslib.com manuals search engine How to Add Fluid Rear Axle
Refer to the Maintenance Schedule to determine what
kind
of transmission fluid to use. See “Recommended
Fluids and Lubricants” in the Index.
Add fluid only after checking the transmission fluid
HOT. (A COLD check is used only as a reference.) If
the fluid level is low, add only enough
of the proper
fluid to bring the
level up to the HOT area for a hot
check.
It doesn’t take much fluid, generally less than a
pint (0.5 L). Don ’t overjX. We recommend you use only
fluid labeled DEXRON@-111, because fluid with that
label is made especially for your automatic transmission.
Damage caused by fluid other than DEXRON-I11 is not
covered by your new vehicle warranty.
After adding fluid, recheck the fluid level as
described under
“How to Check.”
When to Check and Change Lubricant
Refer to the Maintenance Schedule to determine how
often to check
the lubricant and when to change it. See
“Scheduled Maintenance Services” in
the Index.
How to Check Lubricant
If the level is below the
bottom
of the filler plug
hole, you’ll need to add
some lubricant. Add
enough lubricant
to raise
the level to the bottom of
the filler plug hole.
0 When the correct fluid level is obtained, push the
dipstick back
in all the way; then flip the handle
down to lock the dipstick in place.
What to Use
Refer to the Maintenance Schedule to determine what
kind
of lubricant to use. See “Recommended Fluids and
Lubricants” in the Index.
6-19

Downloaded from www.Manualslib.com manuals search engine Composite Headlamps
1. Open the hood.
2. Locate the rear side of each of the headlamps.
3. Without removing the headlamp assembly itself,
remove the bulb assembly from the back of the
headlamp on the driver's side by turning the bulb
counterclockwise one quarter turn.
4. On the passenger side, turn the bulb clockwise
one-quarter turn. Also, to remove the bulb on the
passenger side,
you will need to move the battery.
5. Install a new bulb. Do not handle the glass part of
the bulb.
6. Reverse Steps 3 through 4 to reinstall the headlamp.
6-33

Downloaded from www.Manualslib.com manuals search engine Sidemarker Lamps
3. Remove the bulb assembly from the back of the lens
and replace the bulb.
4. Follow Steps 2 and 3 to replace the bulb. Turn the
socket clockwise to replace it in the lens assembly.
1. Remove the screw from the top of the lens.
6-35

Downloaded from www.Manualslib.com manuals search engine Replacement blades come in different types and are
removed in different ways.
To remove the type with a
release clip:
1.
2.
3.
To remove the old wiper blades, lift the wiper arm
until it locks into
a vertical position.
Press down on the blade assembly pivot locking tab.
Pull down on the blade assembly
to release it from
the wiper arm hook.
Remove the insert from the blade assembly. The
insert has two notches at one end that are locked by
bottom claws
of the blade assembly. At the notched
end, pull the insert from the blade assembly.
4. To install the new wiper insert, slide the notched end
last, into the end with two blade claws. Slide
all the
way through the blade claws
at the opposite end.
5. Be sure that the notches are locked by the bottom
claws. Make sure that all other claws are properly
locked
on both sides of the insert slots.
6. Put the blade assembly pivot in the wiper arm
hook. Pull up until
the pivot locking tab locks in
the hook slot.
7. Carefully lower the wiper arm and blade assembly
into
the windshield.
6-40

Downloaded from www.Manualslib.com manuals search engine Instrument Panel Fuse Block
The fuse block access door
is on the driver’s side of the
~ instrument panel below the
hood release lever.
You can remove fuses with a fuse extractor. The fuse
extractor is mounted to the fuse block access door.
To remove fuses if you don’t have a fuse extractor, hold
the end
of the fuse between your thumb and index finger
and pull straight out.
Be sure
to use the correct fuse. If you ever have a
problem
on the road and don’t have a spare fuse, you
can “borrow” one of the correct value. Just pick some feature
of your vehicle that you can
get along
without
-- like the radio or cigarette lighter -- and use
its fuse,
if it is of the value you need. Replace it as soon
as you can. See “Fuses and Circuit Breakers” in the
Index for more information.
FUSE BLOCK INFORMATION
(u 30A
h DEF~
d 20A a 10A
1;: 1 FDIOq
$2 25A 9
15990609
6-62

Downloaded from www.Manualslib.com manuals search engine POSITION NAME
1. STOP
2. HTD MIR
3. CTSY
4 GAUGES
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Hazard
CRUISE
PWR AUX
Crank
PARK LPS
AIR BAGS
WIPER
HTR-A/C
CIG LTR
ILLUM
DRL
CIRCUITS PROTECTED
Stop/CHMSL, Stoplamps
Electric Heated Mirrors
Courtesy
Lamps, Dome/RDG Lamps, Vanity Mirrors, Power Mirrors
IP Cluster, DRL Relay, DRL Module, HDLP Switch, Keyless Entry
Illumination, Low Coolant Module, CHIME Module, DRAB Module
Hazard LampsKHIME Module
Cruise Control Auxiliary Power Outlet, ALDL
License Plate Lamp, Parking Lamps, Taillamps, Front Sidemarkers,
Glove Box Ashtray
SDM
Wiper Motor, Washer Pump
NC, A/C Blower, High Blower Relay, HTD Mirror
Power Amp, Cigarette Lighter, Door Lock Relay
LP Cluster, HVAC Controls, RR HVAC Controls, IP Switches, Radio
Illumination, Door Switch Illumination
DRL Relay
6-63

Downloaded from www.Manualslib.com manuals search engine POSITION
16.
17.
18.
19.
20.
21.
22.
23.
24.
A.7-
€3.7
NAME
TURN B/U
RADIO-
1
BRAKE
RADIO-B
TRANS RR
FOG
Not Used
Not Used
RR
HVAC
PWR ACCY
PWR WDO
CIRCUITS PROTECTED
Front Turn, RR Turn, Back-up Lamps, BTSI Solenoid
Radio (Ign, Accy)
4WAL PCM,
ABS, Cruise Control
Radio (Battery), Power Antenna
PRNDL, Automatic Transmission
Rear Window Defog
RR HVAC Controls,
HIGH, MED, LOW Relays
Power Door Lock, Six-Way Power Seat, Keyless Entry
Illumination Module
Power Windows
?Circuit Breaker Do
not use fuses of higher amperage than those recommended above. Fuse amperage levels are also imprinted on the
fuse panel under the dash.
6-64