1996 CHEVROLET CAMARO buttons

Downloaded from www.Manualslib.com manuals search engine Operation
The driver’s door will unlock automatically when
UNLOCK is pressed. If UNLOCK is pressed again
within five seconds, the passenger door will also unlock.
All doors will lock when LOCK is pressed.
The hatch will unlock when the button with the trunk
symbol is pressed, as long as the ignition is turned to the
OFF position. If the ignition is on, the trunk button will
only work if the transmission is in PARK
(P) for an
automatic transmission, or if the parking brake is set
on
a manual transmission.
The system will turn
on the interior lamps for about
40 seconds (or until the ignition switch is turned to the
RUN position), when you unlock the doors
or hatch.
The interior lamps will go
off when you lock the doors.
Operating the Remote Lock Control transmitter may
interact with the Vehicle and Content Theft-DeterrentlAlarm
System (if
you have this option). See “Vehicle and Content
Theft-DeterrentlAlarm System” in the Index.
Alarm/Panic Mode
If your vehicle is equipped with the Vehicle and Content
Theft-Deterrent/Alarm System,
you will have a fourth
button on your transmitter. This button is the panic
button.
If you are involved in a panic situation, press this button and
your vehicle’s horn will sound and the
headlamps will flash,
This will draw needed attention to
you and your vehicle. To turn this feature off, either
push the panic button again or turn the ignition to the
RUN position. Note: This feature will
not work if your
ignition
is on or if the transmitter is 30 feet (9 m) or
more away from your vehicle.
Resynchronizing Your Transmitter
If your vehicle does not respond to your transmitter, do
the following to determine what’s wrong:
1. Get closer to the vehicle and try pressing a button
again. Your battery may be low (If
so, see “Battery
Replacement” in the Index).
2. While close to your vehicle, press the LOCK and
UNLOCK buttons
on your transmitter at the same
time and hold for eight seconds. This will attempt to
match your Remote Lock Control transmitter and the
transmitter receiver security
codes.
3. If neither Steps 1 or 2 is successful, your transmitter
may need to be matched to your vehicle. See
“Matching Transmitter(s) to Your Vehicle” in
the Index.
2-7

Downloaded from www.Manualslib.com manuals search engine Transmitter Verification (Option)
This feature provides feedback to the holder of the
Remote Lock Control transmitter that a command has
been received by the Remote Lock Control receiver.
The parking lamps will flash
on every lock and unlock
command and the horn will sound only if the LOCK
button is pushed twice within five seconds. This allows
for silent operation of locking and unlocking, unless a
confirming horn chirp is desired. Other options may be
selected for this feature (see “Feature Customization” in
the Index).
Matching Transmitter@) To Your Vehicle
Each key chain transmitter is coded to prevent another
transmitter from unlocking your vehicle. If
a transmitter is
lost or stolen, a replacement can be purchased through
your dealer. Remember to bring any remaining transmitters
with you when you go
to your dealer. When the dealer
matches the replacement transmitter to your vehicle, any
remaining transmitters must
also be matched. Once the
new transmitter is coded, the lost transmitter will not
unlock your vehicle. Each vehicle can have only four
transmitters matched
to it.
Have each transmitter you intend to match ready for the
next steps. To match transmitters to your vehicle:
0
0
0
0
0
0
0
Turn the ignition switch from the RUN position to
the OFF position. This will disarm the Vehicle and
Content Theft-Deterrent/Alarm System (if your
vehicle has this option).
Remove RADIO fuse. This fuse is located in the
main fuse block, located
on the left side of your
instrument panel. See “Fuses and Circuit Breakers”
in the Index.
Turn the ignition switch from the OFF
to the RUN
position three times quickly (within five seconds.)
The vehicle will respond by locking the doors,
unlocking the driver’s doors and releasing the hatch.
Your transmitter is now ready to match your vehicle.
Press and hold the LOCK and UNLOCK buttons
on
the first transmitter for 15 seconds. The vehicle will
respond as
in Step 3.
Repeat Step 4 for the remaining transmitters.
When you have finished matching all of your
transmitters, replace the RADIO fuse.
Check that all transmitters work by pressing
their buttons.
If the transmitters don’t work, or if you’d rather not match
the transmitters yourself, See your Chevrolet dealer.
2-8

Downloaded from www.Manualslib.com manuals search engine /'
3. Open the latch and close the T-top. Check to see if
there are any gaps showing. Unlatch the T-top and
adjust the sunshade as required.
4. Once the sunshade is installed properly, you can
stick the Velcro@ buttons
on the glass for a proper fit
every time
you install the sunshades. To do this, first
remove the T-top with the sunshade installed and
place it upside down on a table or bench. Take care
not to scratch the glass.
L
5. Pull the sunshade back a little and remove the
backing paper from the Velcro buttons. Push the
sunshade back into place, sticking the Velcro
to
the glass.
6. Install the T-top, close the latch and lock
the T-top. Repeat the above steps for the
passenger-side sunshade.
2-65

Downloaded from www.Manualslib.com manuals search engine AM-FM Stereo with Cassette Tape Player Finding a Station
cI
selection will show on the display.
AM-FM: Press the lower knob to get AM or FM. Your
Playing the Radio
TUNE: Turn the lower knob to choose radio stations.
SEEK: Press the SEEK up or down arrows and the
radio will tune to the
next higher or lower station and
stay there.
SCAN: The scan function uses the same two buttons as
the seek function.
Press and hold the up arrow and then the down arrow to
hear the next higher station for a few seconds. The radio
will go to a station, stop for a few seconds, then go
on to
the next station.
VOL: Turn the upper knob to turn the system on or off,
and to adjust the volume.
RCL: Press the knob to recall the station being played
or
to display the clock. Press
and hold the down arrow and then the up arrow to
hear the next lower station for
a few seconds. The radio
will go to
a station, stop for a few seconds, then go on to
the next station.
Press the up
or down arrow to stop scanning.
3-7

Downloaded from www.Manualslib.com manuals search engine PUSHBUTTONS: The four numbered pushbuttons let
you return to your previously played stations. You can
set up to
14 stations (seven AM and seven FM).
1. Find the station you want by using TUNE.
2. Press SET. (The SET indicator will appear briefly on
the display.)
3. Press one of the four pushbuttons, within five
seconds. Whenever you press that numbered button,
the station you set will return.
4. Repeat the steps for each pushbutton.
In addition to the four stations
set as above, up to three
additional stations may be preset
on each band by
pressing two adjoining buttons at the same time. Just:
1. Tune in the desired station,
2. Press SET. (The SET indicator will appear on
the display.)
3. Press any two adjoining pushbuttons at the same
4. Whenever you press the same buttons, the station
time
(within five seconds).
you set will return.
Setting the Tone
BASS:
Slide the lever up to hear more bass.
TREB: Slide the lever up to hear more treble. Slide the
lever down to reduce noise if
a station is weak or noisy.
Adjusting the Speakers
BAL:
Turn the control behind the upper knob to adjust
the sound between the right and left speakers.
FADE: Turn the control behind the lower knob to move
the sound between the front and rear speakers.
Playing a Cassette Tape
REVERSE:
Press the SEEK arrow that is opposite of
the lit direction arrow to reverse the tape. The tape will
rapidly reverse until STOP-EJECT is pressed lightly.
FORWARD: Press the SEEK arrow that is the
same as the lit direction
arrow to advance the tape
rapidly. The tape will rapidly reverse until STOP-EJECT
is pressed lightly.

Downloaded from www.Manualslib.com manuals search engine APS: This stands for Automatic Program Search. When
you press this button, it changes the function
of the
SEEK arrow buttons.
When the APS.button is pressed, press the
SEEK arrow
that is opposite of the lit direction arrow to repeat the
current selection or skip to the previous selection. The
tape will rapidly reverse until it reaches the beginning
of
a selection. Once it finds the selection, it will change to
play mode.
Press the
SEEK arrow button that is the same as the lit
direction arrow
to skip to the next selection. The tape
will rapidly advance until it reaches the beginning
of a
selection. Once it finds the selection, it will change to
play mode.
PROG-RCL: Press the upper knob to change tape
direction when a tape is inserted.
STOP-E JECT Press this button to remove the tape or
stop playing the tape and switch to the radio.
AM-FM Stereo with Compact Disc Player
Playing the Radio
VOL-BAL:
Turn the upper knob to turn the system on
or off, and
to adjust the volume. Volume increases when
you turn the knob to the right and decreases when you
turn the knob to the left.
RCL: Press the knob to recall the station being played
or to display the clock. RCL may be pressed with the
ignition off
to display the time.
3-9

Downloaded from www.Manualslib.com manuals search engine Finding a Station Setting the Tone
AM-FM: Press the lower knob to get AM or FM. Your
selection will show on the display.
TUNE: Turn the lower knob to choose radio stations.
SEEK: Press the right arrow to tune to the next higher
station and stay there. Press the left arrow
to tune to the
next lower station and stay there.
SCAN: Press this button to hear each station for a few
seconds. The radio will go to
a station, stop for a few
seconds, then
go on to the next station. Press SCAN
again if you hear something you like and want to stay
there.
SC will appear on the display while scanning.
PUSHBUTTONS: The five numbered pushbuttons let
you return to your previously played stations. You can
set up to
10 stations (five AM and five FM).
1. Find the station you want by using TUNE.
2. Press SET. (The SET indicator will appear briefly on
the display.)
3. Press one of the five pushbuttons, within five
seconds. Whenever you press that numbered button,
the station you set will return.
4. Repeat the steps for each pushbutton.
BASS: Press the up arrow to hear more bass and the
down arrow to hear less bass. Press the center of the
button for the factory-preset position. BASS will appear
briefly on the display whenever BASS is pressed.
TREB: Press the up arrow to hear more treble and the
down arrow
to hear less treble. Press the center of the
button for the factory-preset position.
TREB will appear
briefly on the display whenever TREB is pressed.
Adjusting the Speakers
BAL:
Turn the control behind the upper knob to adjust
the sound between the right and left speakers.
FADE: Turn the fade control behind the lower knob to
move the sound between the front and rear speakers.
Playing a Compact Disc
Insert a disc partway into the slot, label side up. The
player will pull it in. The disc should begin playing.
3-10

Downloaded from www.Manualslib.com manuals search engine Delco-Bose AM-FM Stereo with Cassette
Tape Player Finding a Station
AM-FM: Press the lower knob to get AM or FM.
I TUNE: Turn the lower knob to choose radio stations.
SEEK: Press the SEEK up or down arrows and the
radio will tune to the next higher or lower station and
stay there.
SCAN: The scan function uses the same two buttons as
the seek function.
Press and hold the up arrow and then the down arrow to
hear the next higher station for a few seconds. The radio
will go
to a station, stop for a few seconds, then go on to
the next station.
Playing the Radio
VOLUME: Turn the upper knob to turn the system on
or off, and to adjust the volume. Volume increases when
you turn the knob to the right and decreases when you
turn the knob
to the left,
PROG-RCL: Press the knob to recall the station being
played
or to display the clock. PROG-RCL may be
pressed with the ignition
off to display the time. Press and hold
the down arrow and then
the up arrow to
hear the
next lower station for a few seconds. The radio
will go to a station, stop for
a few seconds, then go on to
the next station.
Press the
up or down arrow to stop scanning.
3-12