Page 105 of 354
Downloaded from www.Manualslib.com manuals search engine Twilight Sentinel
I W The control is next to
the headlarnp
knob. It
automatically switches the
lamps on and off by sensing
how dark it is outside.
To operate the twilight sentinel, leave the lamp knob off
and move the TWILIGHT control to any position
but
OFF.
If you move the control all the way to the right, the
lamps will remain
on for approximately three minutes
after the ignition has been turned to the
OFF or LOCK
position. If you move the control so it is just on, the
lamps will go off quickly when you turn the ignition switch out
of RUN. You can adjust the delay time from
only a few seconds to three minutes.
Light Sensor
The light sensor for the DRL and the twilight sentinel is
located in the center of the front defogger grille. If you
cover the sensor, it will read “dark” and the lamps will\
come on.
2-42
Page 106 of 354

Downloaded from www.Manualslib.com manuals search engine c
c-
Exterior Lighting Battery Saver
The exterior lamps will turn off approximately
10 minutes after the ignition is turned to LOCK or ACC, if
the manual park lamp control is on. This protects draining
the battery
in case you have left the headlamps or parking
lamps on. Use the control knob to
turn the lamps back on
indefinitely. To delay the lamps from tuming off, see
"Twilight Sentinel" earlier in this section.
Interior Lamps
Instrument Panel Intensity Control
As you turn the headlamp knob clockwise, the
instrument panel lights will brighten. Turning the
headlamp knob all the way clockwise will turn on the interior lamps.
Lamp Monitors
The rear taillamp monitors
are located at the top
center
of the back glass.
You will see them as you
look through the inside
rearview mirror. The two
red indicators will
illuminate to show that the
taillamps and brake lamps
are working.
Illuminated Entry System
The illuminated entry system turns on the courtesy lamps
and the backlighting
to the door switches and headlamp
knob control when a door is opened or if you press the
Remote Keyless Entry
(RKE) button. Note that the
illuminated entry system
is photocell dependent which
means that it must
be dark outside in order for the
courtesy lamps to
turn on. The courtesy lamps will turn
off approximately 20 seconds after the last door is closed.
2-43
Page 107 of 354
Downloaded from www.Manualslib.com manuals search engine Reading Lamps (Concours Only) Map Lamps
The reading lamps are located in the roof. These lamps
come
on when any door is opened and it is dark outside.
Press the button
to turn them on. Press it again to turn
them
off.
If the reading lamps are left on, they automatically shut
off 10 minutes after the ignition has been turned off.
Courtesy Lamps (DeVille Only)
The courtesy lamps are located in the roof in the rear
seat. These lamps come
on with the lamp knob or when
any door is opened and it is dark outside.
3
These lamps are located in the overhead panel. Press the
button
to turn them on. Press it again to turn them off.
2-44
Page 108 of 354

Downloaded from www.Manualslib.com manuals search engine c
c
c
c
c
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle’s battery
against drainage from the interior lamps,
trunk lamp,
glove box lamp, cigarette lighters or the garage door opener. When the ignition is turned
OFF, the power to
these features will automatically
turn off after 10 minutes
(three minutes if a new car has
15 miles or less). Power
will
be restored for an additional 10 minutes if any door
is opened, the
trunk is opened or the courtesy lamp
switch is turned on.
Battery Guard Storage
This feature is for long term use and miust be
programmed through the DIC while the ignition is in the
RUN position. Battery guard storage protects the battery
by placing the vehicle in a storage mode
so that the
radio, amplifiers, instrument cluster and Remote Keyless
Entry
(RKE) will not drain the battery over a long
period
of time.
To begin programming, press the INFORMATION
and RESET buttons at
the same time for approximately
two seconds. Press the RESET button to answer
“yes” and press the INFORMATION button to indicate a “no” response. The first prompt
to appear relates to the automatic door
locks. This feature can be bypassed by pressing the
INFORMATION button. The STORAGE MODE?
prompt appears next. To select, press the
RESET button.
ENABLE STORAGE MODE? will then appear. A yes
or no response must be given. If the INFORMATION
(no) button is pressed, the DISABLE STORAGE
MODE? prompt will appear. Once again, a yes or no
response is required.
Once the battery guard has been programmed, your
vehicle will enter the storage mode approximately
20 minutes after the ignition key has been turned off.
The RKE will also be disabled at this point. The RKE
will reactivate when a door or the trunk is opened,
however,
if your vehicle is left inactive for another
20 minutes the RKE will re-enter the storage mode.
Your vehicle will stay in the storage mode until the
ignition key
is turned out of LOCK. The system will
“wake-up” when the
door key is inserted into the door
however, your vehicle will remain in the storage mode.
The ignition must be out of
LOCK before the battery
guard is disabled.
2-45
Page 109 of 354
Downloaded from www.Manualslib.com manuals search engine Mirrors
Electrochromic DaylNight Rearview Mirror
Your Cadillac has an electrochromic day/night
rearview mirror.
This mirror automatically changes to reduce glare
from '
headlamps behind you. A photocell on the back of the
mirror senses when it is becoming dark outside. Another
photocell built into the mirror surface senses when
headlamps are behind you.
At night, when the glare is too high, the mirror will
gradually darken
to reduce glare (this change may take a
few seconds). The
mirror will return to its clear daytime
state when the glare is reduced.
3
4
3
Page 110 of 354
Downloaded from www.Manualslib.com manuals search engine On/Off Switch Time Delay
This feature prevents rapid changing
of the mirror from
the night mode to the day mode as you drive under lights and through traffic.
c I
I
I
Press the button at the base of the mirror to turn on the
automatic feature. The button has
an indicator light to
show it is on. Press the button to turn the automatic
feature
off.
Reverse Gear Day Mode
The reverse mode is another important feature of the
automatic mirror. When the shift lever is placed in
REVERSE (R), the mirror changes to the day mode.
This gives
you a bright image in the mirror as you
back up.
Cleaning Photocells
Use a cotton swab and glass cleaner to clean the front
and rear photocells that make the auto-dimming
feature
work.
2-47
Page 111 of 354
Downloaded from www.Manualslib.com manuals search engine Electrochromic Day/Night Rearview Mirror
with
Compass (Option)
L
1
This mirror automatically changes to reduce glare
when set in the
M (Mirror) or C/M (Compass/Mirror)
positions. One photocell
on the back of the mirror
senses
when it is becoming dark outside. Another
photocell
is built into the mirror surface to sense
headlamps behind
you.
Setting the Sensitivity
r
OFF: This setting turns off the day/night function and
compass.
The mirror will stay in the day mode.
M: This turns on the day/night portion of the mirror to
automatically reduce glare.
C/M: This setting turns on the compass in addition to
the day/night function. The letter or letters displayed in
the top right comer
of the mirror indicate the direction
in which you are traveling.
2-48
Page 112 of 354

Downloaded from www.Manualslib.com manuals search engine Time Delay
This feature prevents rapid changing of the mirror from
the night mode
to the day mode as you drive under
lights and through traffic.
Compass Calibration
r
r
r
r
Reverse Gear Day Mode
The reverse mode is another important feature of the
automatic mirror. When the shift lever
is placed in
REVERSE (R), the mirror changes to the day mode.
This gives you a bright image in the mirror as you
back up.
Cleaning Photocells
Use a cotton swab and glass cleaner to clean the front
and rear photocells that make the auto-dimming
feature work. Once the compass is calibrated,
it does not need to be
recalibrated. To calibrate
the compass:
1. Set the switch on the mirror control to C/M.
2. Turn the vehicle ignition switch on. The letter C
should be displayed in the mirror compass window.
If not, hold the CAL switch (on the bottom of the
mirror)
for more than 10 seconds, and the letter C
will appear. To hold in the CAL switch, insert a
paper clip into the small hole on the bottom of the
mirror housing. The display will show a number first, but keep holding until the letter
C appears.
3. For quick calibration, drive the vehicle in a
360-degree circle at less than
5 mph (8 km/h) until
the display reads a compass direction.
For nonnal
calibration, drive the vehicle
on your everyday
routine, and the compass will eventually calibrate.
r
2-49