1996 AUDI A4 Brakes Read Mesure Value Block 08 Workshop Manual

01-146
Test table: display group 3 Read measuring value block
3
Indicated on display
60 to
8000
1 RPM 0 to 100
%
0 or 1
---


Traction control (ASR) button: (Only for vehicles equipped with ASR)

0 Traction control button not operated. 1 The traction control button is operated, operational condition of ASR alternates, i.e. "ASR
OFF" and "ASR ON".
- Check traction control button if there are deviations. Carry out "Electrical test", step 11 page 01
-
166
.

Actual engine torque (AET): (Only for vehicles equipped with ASR)
0% vehicle is in deceleration mode.20% - 30% represents engine idle.100% engine is offering its maximum torque.
- If no indication is displayed, proceed according to DTC 00647 "ABS-ASR engine electrical connection 2".
Diagnostic Trouble Code (DTC) table
Engine speed: (Only for vehicles equipped with ASR)

Engine speed is displayed in increments of 60 RPM, starting at 60 RPM.
- If no indication is displayed, proceed according to DTC 00529 "Wheel speed information missing. No signal". Diagnostic
Pa
ge 9 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

Trouble Code (DTC) table
Pa
ge 10 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

01-147

Note:
The display group numbers can be selected in
sequence by pressing buttons <-1 and 3-> on the
VAG1551 scan tool, or the arrow buttons and
on the VAG1552 mobile scan tool.
- Press -C- button to input display group number
manually. Read Measurin
g Value Block
Enter displa
y group number XXX

Indicated on display:
- Press buttons -0-, -0- and -4-.
- Press -Q- button to confirm input.
Pa
ge 11 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

01-148
Test table: display group 4 Read measuring value block
4
Indicated on display
Std:min
or too large
or ERROR
or invalid 0 or 1

0 or 1
---


EDL/ASR shut-off: (Only for vehicles equipped with EDL or ASR)
This possibility is only provided for development purposes.0 EDL/ASR available1 EDL/ASR not available

EDL shut-off due to excessive brake temperature: (Only for vehicles with EDL)

0 EDL was not shut off during the last 20x "ignition switched on and off". 1 EDL was shut off during the last 20x "ignition switched on and off".
Standing time: (Only for vehicles equipped with EDL)

too large: A standing time larger than 255 hours and 59 minutes is not indicated on the display.
ERROR: Two valid and matching time transmissions from the instrument cluster to the ABS control module (w/EDL) -
J104- did not occur after ignition was switched on and engine was started. Check whether the DTC 01203
"ABS/instrument cluster electrical connection" is stored in DTC memory.
Pa
ge 12 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

Invalid: Standing time could not be obtained during this ignition cycle. Standing time calculation must be activated for at
least 20 seconds when the first component is operated for the first time when ignition is switched on after the instrument
cluster or the hydraulic control module have been replaced. The standing time will be indicated the next time ignition is
switched on.
Pa
ge 13 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12