1996 AUDI A4 engine

24-23

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -3- and -2- to input display group number 32 (032),
and press -Q- button to confirm input.
Read Measuring Value Block 32 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 30 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-27
Evaluation of display group 32 Display group:
32


Display fields:
1-4
Possible malfunction cause
Corrective action
O2S control
learning value:
-25.0 to -10.0
%
Engine oil dilution (when part load learning value is
normal display fields 2 and 4)
- Change engine oil, or carry out extensive
road test and check again


Fuel pressure too high- Check fuel pressure regulator page 24
-
111



Fuel injector leaking- Check fuel injectors page 24
-102


Oxygen Sensor (O2S) heater malfunction- Check O2S heater page 24
-34
O2S control
learning value:
10.0 to 25.0 %
Intake air leaks ("false air") or exhaust manifold leaks
(when partial load learning value is normal display
fields 2 and 4)
- Check intake air system for leaks page 24
-126

- Check exhaust system for leaks Repair
Manual, 2.8 Liter V6 5V General, Engine,
Repair Group 26


Fuel pressure too low- Check fuel pressure regulator page 24
-
111



Oxygen Sensor (O2S) heater malfunction- Check O2S heater page 24
-34
Pa
ge 36 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-29

Checking HO2S reference voltage (Banks 1,
2)

- Disconnect 4-pin connector for respective
HO2S.

If voltage is NOT OK:
If voltage is OK: - Connect multimeter US1119 (Fluke 83 or equivalent) between harness
connector terminals 3 and 4 (to ECM), using adapter cables from
VW1594 connector test kit.
- Start engine and measure voltage.
Specified value: 0.40-0.50 volts
- Switch ignition off.
- Check HO2S wiring.

Bank 1, sensor 1 page 24
-30
.

Bank 2, sensor 1 page 24
-32
.
- Replace respective Heated Oxygen Sensor (HO2S).
Pa
ge 39 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

Fuse for Oxygen Sensor (O2S) heater(s) OK
Engine Coolant Temperature (ECT) at least
80 C (176 F)
Pa
ge 45 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-35

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -4- and -0- to input display group number 40 (040),
and press -Q- button to confirm input.
Read Measuring Value Block 40 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 46 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

Wiring diagram

Test requirements
Engine Coolant Temperature (ECT) at least
80 C (176 F)
Pa
ge 55 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-43

Function test

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -3- and -6- to input display group number 36 (036),
and press -Q- button to confirm input.
Read Measuring Value Block 36 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 56 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-45

Continuation

- Road test to condition oxygen sensor (eliminate
possible contamination) and repeat test.
If the values are still NOT OK:

- Check Oxygen Sensor (O2S) heater(s) page
24
-52
.

- Briefly accelerate engine over 3000 RPM.
If the value in either display field 1 or field 3
remains constant:
page Page 24
-46
, Evaluation of display group
36.
Pa
ge 58 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1