1995 RENAULT MEGANE SCENIC relay

DIESEL EQUIPMENT
Special notes
13
2. Control by altimetric capsule
At altitude, when atmospheric pressure is
approximately 925 ± 20 mbars, the ALFB
solenoid valve is fed via a relay and the
altimetric capsule.
KEY
257Pre-heating unit
597Engine fuse box
711ALFB solenoid valve mounted on injection
pump
741Altimetric capsule
743Altimetric relayLOCATION
Altimetric capsule (741)
PRJ9925799334R
13-19

DIESEL EQUIPMENT
Pre-post-heating unit
13
DIAGRAM KEY
104Ignition switch
163Starter
171Air conditioning clutch
206Air conditioning trifunction pressure switch
247Instrument panel
251Bi-function coolant temperature switch
257Pre-heating unit
398EGR solenoid valve
412Fast idle solenoid valve (AC version)
597Engine fuse box
642AC / pre-heating separation diode
645Passenger compartment fuse box
680Pre-heating unit n° 1
681Pre-heating unit n° 2
682Pre-heating unit n° 3
683Pre-heating unit n° 4
711Diesel fuel pump
741Altimetric capsule
743Altimetric relay
777Power feed for fuse boxConnector (A)
+ Bat+ before ignition feed
Connector (B)
1Feed to heater plugs 1 and 3
2Feed to heater plugs 2 and 4
Connector (C)
A1 / S2Load dependence solenoid valve
control
A2 / PCLoad lever microswitch information
A3 / CTNCTN type sensor coolant temperature
information
B1/+APC+ after ignition feed
B2 / DEMStarter information
B3 / TemPre-heating warning light control (via
earth)
C1 / S1Not used
C2 / -Bat Earth
C3 / ClimFast idle solenoid valve control during
post-heating phase
92206-2R
IDENTIFICATION OF CONNECTORS
13-30

DIESEL EQUIPMENT
Fuel filter
13
LOCATION
Principle of the electric heater
The heater has heated studs. They are ceramic,
made from barium titanate which has a positive
temperature coefficient, meaning that its
resistance increases as its temperature increases.
99332R
1Fuel filter
2Electric heater
3Hand priming unit
The electric diesel fuel heater and the thermostat
are integral in the head of the filter.
DIAGRAM
PRJ99258
449Electric heater
450Diesel heating relay
597Engine fuse box
645Passenger compartment fuse box Operating temperature
Electrical circuit closes: 0°C
Electrical circuit opens: from 8°C
Heater power: 150 W
13-37

INJECTION
General
17
K7M engine
1Injection computer
2Pinking sensor
3Coolant temperature sensor
4TDC sensor
5Fuel vapour recirculation solenoid valve
7Idle speed regulation stepping motor
8Throttle position potentiometer
9Air temperature sensor
10Absolute pressure sensor
11Canister
12Coil for cylinders 1 - 4
13Coil for cylinders 2 - 3
14Fuel pump relay
15Anti-interference condenser
16Air filter
17Oxygen sensor
18Power assisted steering pressostat
19EGR solenoid valve
20Vacuum reservoir
21EGR air filter
LOCATION OF COMPONENTS
17-9

INJECTION
General
17
F3R engine
1Injection computer
2Pinking sensor
3Coolant temperature sensor
4TDC sensor
5Fuel vapour recirculation solenoid valve
6Cylinder reference sensor
7Idle speed regulation solenoid valve
8Throttle position potentiometer
9Air temperature sensor
10Absolute pressure sensor
11Canister
12Coil for cylinders 1 - 4
13Coil for cylinders 2 - 3
14Fuel pump relay
15Anti-interference condenser
16Air filter
17Oxygen sensor
LOCATION OF COMPONENTS
17-11

INJECTION
Operating wiring diagram
17
KEY TO OPERATIONAL WIRING DIAGRAMS (E7J, F3R, K7M)
COMPONENT NO DESCRIPTION
109
119
120
146
147
149
193 to 196
218
222
224
225
228
236
238
242
244
247
250
272
310
319
341
371
398
437
565
597
645
649
663
664
679
746
772
777
927
MF
MHOn board computer
Automatic transmission computer
Injection computer
Pinking sensor (located under the inlet manifold for E7J engine)
Absolute pressure sensor
TDC sensor
Injectors
Fuel pump
Throttle position potentiometer
Power assisted steering pressostat
Diagnostic socket
Idle speed regulation micromotor
Fuel pump relay (in engine fuse box)
Injection feed locking relay
Oxygen sensor
Coolant temperature sensor
Instrument panel
Vehicle speed sensor
Air temperature sensor
Ignition power module
Air conditioning control panel
Idle speed regulation solenoid valve
Fuel vapour recirculation solenoid valve
Exhaust gas recirculation solenoid valve (EGR)
Throttle body heater (under throttle body)
Throttle body assembly
Engine fuse box
Passenger compartment connection unit
Idle speed regulation stepping motor
Dual ignition coil n°1 (cylinders 1 and 4)
Dual ignition coil n° 2 (cylinders 2 and 3)
Radio anti-interference condenser
Cylinder reference sensor
Heater relay (in engine fuse box)
Power fuse board (near battery)
Inertia switch
Rear right hand electrical earth
Engine electrical earth (located on the cylinder block between the starter and the al-
ternator for the E7J engine)
17-39

INJECTION
Operating wiring diagram
17
E7J engine
COMPUTER TRACK ALLOCATION
TrackALLOCATION
1Power earth
2Electronic earth
3Vehicle speed information
4+ before ignition (permanent) computer memory
5Canister bleed signal (sequential earth period)
6Pump relay control (via track N° 2)
7Locking relay control (via track N° 2)
8Diagnostic line for erasing the memory and power assisted steering pressostat information
9Throttle position potentiometer information (pin N° 4 on 222)
10Heater relay command
11TDC sensor signal (track B)
12Rev counter information at instrument panel
13Connection with injection fault warning light on instrument panel
14Air temperature information
15Coolant temperature information
16+ 5 V feed for absolute pressure sensor and throttle potentiometer
17Common earth for absolute pressure sensor, throttle potentiometer and coolant temperature
sensor
18Emission of diagnostic signal to diagnostic socket
19Main computer feed via injection locking relay
20Air conditioning compressor command
21Injector control via earth
22Not used
23+ or - feed to idle speed micromotor (pin N° 1)
24+ or - feed to idle speed micromotor (pin N° 2)
17-41

INJECTION
Operating wiring diagram
17
TrackALLOCATION
25Not used
26Not used
27Not used
28Command for coil for cylinders 1 and 4
29Command for coil for cylinders 2 and 3
30Command for injector n° 1 and n° 4 via earth (n° 1 flywheel end)
31Pinking sensor screened cable
32+12 V before ignition
33TDC sensor signal (track B)
34TDC sensor signal (track A)
35Stepping motor command (0 - 12 V)
36Stepping motor command (0 - 12 V)
37Immobiliser coded line input
38Uni-directional diagnostic line L for entry into diagnostic mode only
(looking for computer)
39Not used
40Stepping motor command (0 - 12 V)
41Throttle angle information for automatic transmission computer
42RCO control (sequential earth period for canister bleed solenoid valve RCO)
43Command for injection fault warning light on instrument panel
44Common earth for pinking sensor and coolant temperature sensor and absolute pressure sensor
45+ 5 V feed for absolute pressure sensor and throttle position potentiometer
46Common earth for air temperature sensor and throttle position potentiometer
47Not used
48Command (via earth) for fuel pump relay and engine speed information
49Not used
K7M engine
17-45