1995 RENAULT MEGANE SCENIC check engine

MANUAL GEARBOX
5th gear on the vehicle
21
Put a wooden block between the 5th gear fork
and the drive gear to take the backlash and refit a
new pin into the 5th gear fork using B.Vi. 31-01
complying with the assembly direction, the split
should be pointing towards the rear housing.
90498-1S
85979R1
Fit a new O-ring to ensure that the rear housing is
sealed.
Return the gearbox to neutral and check that all
gears can be engaged.
If any problems occur, check that reverse gear is
not engaged.Fit the rear housing by engaging nozzle (A) into
the primary shaft.
Tighten the mounting bolts to a torque of 2.4
daN.m.
87180R
Fill the gearbox with oil.
Check that the rear housing does not leak when
the engine is running.
21-22

AUTOMATIC TRANSMISSION
Oil change frequencies
23
The mechanism is drained during the major service.
The oil level must be checked every 10000 miles (15 000 km) in case there is a slight oil leak.
The final drive is never drained ; it is filled for life.
The strainer is no longer replaced (NT 2261A).
Only the level may change due to a slight leak.
Oil capacity
NOTE :if the automatic transmission is replaced, only check the oil level since the transmission is supplied by
the Parts Department full of oil.
TOTAL volume
MECHANISM
5.7 l
FINAL DRIVE1 l
Fault warning light
MESSAGE FROM THE ELECTRONIC FAULT
WARNING LIGHT
Normal operation :
• The warning light is not illuminated during
normal operation whether the vehicle is being
started, engine running or when the vehicle is
stationary.
Presence of a fault :
• Vehicle stopped, engine running, or when
driving, warning light permanently illuminated
• Vehicle moving, warning light illuminates and
extinguishes without action at the ignition key.
• Vehicle moving, warning light illuminates
briefly.Oil temperature < - 20 °C or > + 140 °C
• Vehicle moving or stationary, warning light
flashes at a rate of approximately 1 flash per
second, in this case, reduce the performance
requirement by moderating acceleration.
23-6

Oil pressure
Before starting:
- if the gearbox has been drained, fill it with 3.5
litres of oil,
- if you are simply checking the level, you must
add 0.5 litre of the recommended type of oil.
1-Vehicle on a 4 post lift, transmission at am-
bient temperature.
2-Start the engine with the selector lever in the
Park position.
3-Connect the
XR25 test kit and enter:
D14then
#0 4
4-Raise the vehicle and allow the engine to run
until it reaches a temperature of 60 °C.
5-When the desired temperature has been rea-
ched, open the top-up plug; allow the excess
oil to overflow (must be more than 0.1 litre)
for approximately 20 seconds. Replace the
plug
6-If the volume of oil which flowed out is less
than 0.1 litre, the level is not correct. Repeat
the operation.
In this case, add 1 litre of the recommended oil
and allow the transmission to cool down between
successive operations.
AUTOMATIC TRANSMISSION
Filling - Levels
23
FILLING - TOPPING UP
Filling is performed though tube (D).
Use a funnel fitted with a 15/100 filter so as to
prevent any impurities entering.
The level
MUST be checked in accordance with the
following method:
94845R1
The transmission is fitted with an oil pressure
take-off. Connect the B.Vi. 1215 to check the
automatic transmission pressure sensor only.
The oil pressure cannot be altered.
Its value is determined by the electronic compu-
ter.
94845-1R
23-8

AUTOMATIC TRANSMISSION
Automatic transmission (Removal - Refitting)
23
K7M
ENGINE
Separate the gearbox from the engine by :
- removing the starter motor,
- removing the bolts from the automatic trans-
mission sump.
Remove:
- the hoses on the exchanger, Lift the engine from the sub-frame.
91131S
- the converter bolts
- the bolts around the gearbox and the TDC sen-
sor.
Separate the automatic transmission from the en-
gine.
REFITTING (special notes)
Refit the converter by positioning it with respect
to the mounting bolts.
Tighten the bolts around the automatic transmis-
sion.
Refitting is the reverse of removal.
Aligning the engine sub-frame with the body will
be made easier by positioning two approximately
100 mmlong threaded rods in the two front sub-
frame-body mountings.
Tighten the sub-frame front mounting bolts to a
torque of 6 daN.m. and to a torque of 11 daN.m at
the rear.
Tighten all nuts and bolts to the re-
commended torque.
Fit the caliper mounting bolts using Loctite
FRENBLOC and tighten them to the correct tor-
que.
Press the brake pedal several times to bring the
pistons back into contact with the brake pads.
Fill:
- the cooling circuit and purge it (see chapter 19),
- the engine with oil if necessary.
NOTE : check that the steering shaft yoke spacer is
in place when refitting.
99586R2
23-19

AUTOMATIC TRANSMISSION
Checking the "timing point" on the converter
23
Put the vehicle on a two post lift.
Lift the vehicle until the wheels are a few centime-
tres off the ground.
Connect the
XR25.
Put the
ISO switch on S8.
Enter the A4.2 transmission code :
D14
then #06 to display the engine speed.
Accelerate fully with the brake fully on.
The engine speed should stabilise to :
-K7M engine: 2430 rpm.
If this value is not correct, replace the converter.
A timing point which is more than 200 rpm. below
the specified value requires the automatic trans-
mission to be replaced.
NOTE : for all diagnostic questions, refer to MR
TA.A, "General".
23-29

17
INJECTION
Fault finding - Checking conformityF3R engine

17
INJECTION
Fault finding - Checking conformityF3R engine

17
INJECTION
Fault finding - Checking conformityF3R engine