1995 PONTIAC PONTIAC clock

Lower the vehicle by turning the jack handle
counterclockwise, Lower
the jack completely.
Tighten the wheel nuts
firmly in a crisscross
sequence as shown.
5-29
ProCarManuals.com

Filling Your Tank The cap is behind a hinged door on the left side of your
vehicle.
While refueling, hang the cap inside the fuel
door.
To take off the cap, turn it slowly to the left
(counterclockwise).
6-5
ProCarManuals.com

Headlamps @-Door Models)
1. Open the headlamp panel.
2. Turn the socket
counterclockwise until
it pops loose from the
housing.
3.
4.
5.
6.
7.
Pull out the bulb socket.
Lift the plastic locking tab on the electrical
connector and pull the connector
from the bulb
socket.
Snap the electrical connector into
a new bulb socket.
Replace the bulb socket into the housing
and turn
clockwise.
Close the headlamp panel.
6-35
ProCarManuals.com

5. Pull the lamp bar housing away from the body of the
vehicle.
K uw
6. Squeeze the tab on the socket and turn the socket
counterclockwise.
7. Pull out the socket.
8. Pull the bulb out of the socket.
9. Push in a new bulb.
10. Replace the socket into the lamp bar assembly and
11. Replace the lamp
bar assembly to the body of the
turn clockwise.
vehicle.
12. Install the wing nuts.
13. Put the covers back and install the pins.
6-37 ProCarManuals.com

Front Sidemarker (&Door Models) Front Turn Signal (2-Door Models)
1.
2.
Remove the screws and
pull the sidemarker
housing forward.
Turn the socket
counterclockwise and
pull the socket out
of the
housing.
3.
4.
5.
6.
7.
Pull the bulb out of the socket.
fish
in a new bulb.
Replace the socket into the housing
and turn
clockwise.
Replace the housing to the vehicle.
Install the screws-
45 -3
L A
1. Remove the pins from the cover above the turn
signal lamps.
6-38 ProCarManuals.com

3.
4.
5.
6.
7.
Turn the socket
counterclockwise 1/6-tum until it feels
loose.
Pull out~the socket.
Pull the bulb out
of the socket.
Push
in a new bulb.
Replace the socket into the housing and
turn
clockwise until it snaps in place.
Replace the cover and pins.
Front Turn Signal (4-Door Models)
)I 1. Remove the screws and
3. Pull out the bulb socket.
2.
pull the turn signal
housing forward.
Turn the bulb socket counterclockwise until
it pops loose from the
housing.
4. Lift the plastic locking tab on the electrical
connector and pull the connector from the bulb
socket.
5. Snap the electrical connector into a new bulb socket.
6. Replace the bulb socket into the housing and turn
clockxvise.
7. Replace the housing to the vehicle.
8. Install the screws.
6-39 ProCarManuals.com

Fog Lamps (&Door Models)
1. Remove the pins from the cover above the fog
lamps.
3.
4.
5.
6.
7.
8.
2.
Pull out the bulb socket. Turn
the bulb socket
counterclockwise until
it
pops loose from the
housing.
Lift the plastic locking tab on the electrical
connector and pull the connector from the bulb
socket.
Snap the electrical connector into a new bulb socket.
Install the screws.
Replace the socket into the housing and turn
clockwise until it snaps in place.
Replace the cover and pins.
6-4 1 ProCarManuals.com

If the socket has a tab, squeeze it. Turn the socket
counterclockwise. 2.
3.
4.
5.
6.
7.
Pull out the socket.
Pull the bulb aut
of the socket.
Push in a new bulb.
Replace the socket into the housing and
turn
clockwise.
Reposition the carpet and install the plastic retainers.
ProCarManuals.com