1995 OLDSMOBILE AURORA headlamp

Keep your windshield and all the glass on your vehicle
clean
-- inside and out. Glare at night is made much
worse by dirt
on the glass. Even the inside of the glass
can build up a film caused by dust. Dirty glass makes
lights dazzle and flash more than clean glass would,
making the pupils
of your eyes contract repeatedly.
Remember that your headlamps light up f’ar less of a
roadway when you are
in a turn or curve. Keep your
eyes moving; that way, it’s easier to pick out dimly
lighted objects. Just as your headlamps should be
checked regularly for proper aim,
so should your eyes
be examined regularly. Some drivers suffer
from night
blindness
-- the inability to see in dim light -- and aren’t
even aware
of it.
Driving in the Rain
Rain and wet roads can mean driving trouble. On a wet
road you can’t
stop, accelerate or turn as well because
your tire-to-road traction isn’t
as good as on dry roads.
And,
if your tires don‘t have lnuch tread left, you’ll get
even
less traction. It’s always wise to go slower and be
cautious if-’ rain starts to fall while you are driving. The
surfice may
get wet suddenly when your reflexes are
tuned for driving
on dry pavement.
4-16
ProCarManuals.com

Hydroplaning doesn‘t happen often. But it can if your
tires haven’t much tread or
if the pressure in one or
more is low.
It can happen if a lot of water is standing on
the road.
If you can see reflections from trees, telephone
poles, or other vehicles, and raindrops “dimple” the
water’s surface, there could be hydroplaning.
Hydroplaning usually happens at higher speeds. There
just isn’t a hard and fast rule about hydroplaning. The
best advice is to slow down when
it is raining.
Some Other Rainy Weather Tips
0
0
0
Turn on your low-beam headlamps -- not just your
parking lamps
-- to help make you more visible to
others.
Besides slowing down, allow some extra following
distance. And be especially careful when you pass
another vehicle.
Allow yourself more clear room
ahead, and be prepared to have your view restricted
by road spray.
Have good tires
with proper tread depth. (See
“Tires”
in the Index.)
City Driving
One of the biggest problems with city streets is the
amount of traffic on them. You’ll want to watch out for
what the other drivers are doing and pay attention to
traffic signals.
4-18
ProCarManuals.com

Run your engine only as long as YOLI must. This saves
fuel. When you
run the engine, make it go a little faster
than just idle. That is, push the accelerator
slightly. This
o
uses less fuel for the heat that you get and it keeps the
battery charged. You will need a well-charged battery t
restart the vehicle. and possibly for signaling later on
with your headlamps. Let the heater run for awhile.
--
Then, shut the engine off and close the window almost
all the way to preserve the heat. Start the engine again
and repeat this only when you feel really uncomfortabl e
from the cold.
But do it as little as possible. Preserve the
fuel
as long as you can. To help keep warm? you can get
out of the vehicle and
do some fairly vigorous exercises
every half hour or
so until help comes.
4-27
ProCarManuals.com

Headlamp Aiming
Your vehicle has the composite headlamp system. These
headlamps have horizontal and vertical aim indicators.
The
aim has been pre-set at the hctory and should need
no further adjustment.
If your vehicle is damaged in an accident and the
headlamp aim seems to be affected, see your Aurora
retailer. Headlamps
on damaged vehicles may require
recalibration
of the horizontal aim by your Aurora
retailer.
To check the aim, the vehicle should be properly
prepared as follows:
The vehicle must have all four tires on a perfectly
level surface.
The vehicle should not have any snow, ice, or mud
attached
to it.
0 There should not be any cargo or loading of vehicle,
except
it should have a full tank of gas and one
person or
160 Ibs. (75 kg) on the driver's seat.
Tires should be properly inflated.
I NOTICE:
To make sure your headlamps are aimed
properly, read all the instructions before
beginning. Failure to
follow these instructions
could cause damage to headlamp parts.
State inspection stations will allow a vertical reading of
plus
0.76 degrees or minus 0.76 degrees from the center
of the bubble.
It is recolnmended that the upper limit not exceed plus
0.4 degrees from the center of the bubble. Other drivers
may flash their bright lights at you
if your adjustment is
much above plus 0.4 degrees.
If you find that the headlamp aiming needs adjustment,
follow these steps:
Start with the vertical headlamp aim. Don't try to adjust
the horizontal aim first. Adjustment screws can be
turned
with an E8 Torx@socket or T1S TorxB
screwdriver.
6-28
ProCarManuals.com

1. Check the vertical aim for each headlamp and adjust
it as necessary. Turn the vertical aiming screw until
the bubble in the level is centered at 0 (zero).
2. Now acl-just the horizontal aim. Check the horizontal
aim for each headlamp and adjust
it as necessary.
TLII-11 the horizontal aiming screw
until the pointer is
lined
up with the 0 (zero).
3. Now, re-check the vertical aim, to make sure it is
still correct after the horizontal aim adjustment.
Read.just.
if necessary.
6-29
ProCarManuals.com

Headlamp Bulb Replacement
For the type of bulb, see "Replacement Bulbs'' in the
Index.
Low Beam Bulbs
1. Remove the air cleaner cover to get to the driver's
side headlamp bulb.
To do this:
a. Remove the radiator hose (A) from the resonator
channel.
b. Release tension of the wing screw clamp (B) on the
air intake duct where it attaches to the air cleaner
cover near the top
of the engine. Turn the wing
screw counterclockwise, then detach the hose
from
the air cleaner cover.
c. Push the duct and resonator assembly
(C) rearward
and up, and hold them out of the way.
2. Twist the bulb assembly 1/6 turn and pull out the
bulb assembly.
6-30
ProCarManuals.com

3. Unclip the bulb
assembly from the
wiring harness and
replace the bulb
assembly. High Beam Bulbs
1. Pull up on the wiring harness. This unlocks the bulb.
4. Reverse steps 1-3 to replace the bulb assembly,
headlamp housing and air cleaner cover and tube.
2. Now you can reach in behind the lamp housing and
pull out the bulb.
3. To replace the bulb, angle the new bulb into the
empty socket.
4.
Push the base of the bulb down to lock it into place.
6-3 1
ProCarManuals.com

Wheel Replacement
Replace any wheel that is bent, cracked, or badly rusted
or corroded. If wheel nuts keep coming loose, the wheel,
wheel bolts, and wheel nuts should be replaced.
If the
wheel leaks air, replace it (except some aluminum
wheels, which can sometimes
be repaired). See your
Aurora retailer if any
of these conditions exist.
Your retailer will know the kind
of wheel you need.
Each new wheel should have the same load carrying
capacity, diameter, width, offset, and be mounted the
same way as the one it replaces.
If you need
to replace any of your wheels, wheel bolts,
or wheel nuts, replace them only with new
GM original
equipment parts. This way, you will be sure to have the
right wheel, wheel bolts, and wheel nuts for your Aurora
model.
I NOTICE:
The wrong wheel can also cause problems with
bearing life, brake cooling,
speedometer/odometer calibration, headlamp aim, bumper height, vehicle ground clearance,
and tire
or tire chain clearance to the body and
chassis.
6-41
ProCarManuals.com