1995 LAND ROVER DISCOVERY battery

19FUEL SYSTEM
4
REPAIR MULTIPORT FUEL INJECTION RELAYS
Service repair no - 19.22.08
The two Multiport fuel injection relays are located in
the RH footwell area behind the 'A' post trim panel.
The fuel injection relays can be identified as follows:
A. Fuel pump relay - Blue base
B. Main relay - Black base
Remove
1.Release front door seal from 'A' post.
2.Remove lower 'A' post trim panel.
3.Pull relay from base.
Refit
4.Reverse removal procedure.ENGINE CONTROL MODULE (ECM)-14 CUX
Service repair no - 19.22.34
NOTE: The ECM is not serviceable, in
event of unit failure it must be replaced.
Remove
1.Remove the fascia right-hand closing panel.
2.Remove the right-hand footwell side panel trim.
3.Disconnect battery negative lead.
4.Release ECM plug retaining clip.
5.Maneouvre the front of the plug (in the direction
of the bold arrow) and detach the other end of
the plug from the retaining peg.
6.Release the two screws securing the ECM to the
right-hand footwell side panel.
7.Withdraw the ECM from the clip.
Refit
8.Refit the ECM securely in the clip and fit the two
screws.
9.Reconnect the ECM harness plug. Ensure that
the plug is pushed firmly into its location and that
the retaining clip secures the plug in position.
10.Reverse removal procedure.

MFI
5
REPAIR INERTIA FUEL SHUTOFF SWITCH
Service repair no - 18.30.35
The inertia fuel shutoff switch is located on the
bulkhead next to the washer reservoir under bonnet
[hood].
Remove
1.Disconnect battery negative lead.
2.Disconnect multiplug from inertia switch.
3.Remove 2 screws securing inertia switch to
mounting bracket.
4.Remove inertia switch.
Refit
5.Position inertia switch to mounting bracket and
secure with screws.
6.Connect multiplug to inertia switch.
7.Reconnect battery negative lead.ENGINE FUEL TEMPERATURE SENSOR
Service repair no - 19.22.08
Remove
NOTE: Fuel leakage will not occur when
sensor is removed from fuel rail, therefore
it is not necessary to depressurise the fuel
system.
1.Disconnect battery negative lead.
2.Disconnect multi-plug from sensor.
3.Release sensor from fuel feed rail.
Refit
4.Reverse removal procedure. Ensure sensor is
tightened securely in fuel rail.

19FUEL SYSTEM
6
REPAIR ENGINE COOLANT TEMPERATURE SENSOR
Service repair no - 19.22.18
Remove
1.Position drain tray to collect coolant spillage.
2.Disconnect multiplug from coolant sensor.
3.Remove sensor from thermostat housing.
4.Remove and discard copper washer.
Refit
5.Fit a new copper washer.
6.Fit sensor and tigten securely.
7.Top-up cooling system.
8.Run engine, check for water leaks around
sensor.DEPRESSURISING FUEL SYSTEM
WARNING: Under normal operating
conditions the Multiport fuel injection
system is pressurised by a high pressure
fuel pump, operating at up to 2.3 to 2.5 bar When
engine is stationary pressure is maintained within
system. To prevent pressurised fuel escaping and
to avoid personal injury it is necessary to
depressurise multiport fuel injection system
before any service operations are carried out.
If vehicle has not been run there will be a small
amount of residual pressure in fuel line. The
depressurising procedure must still be carried out
before disconnecting any component within the
fuel system.
The spilling of fuel is unavoidable during this
operation. Ensure that all necessary precautions
are taken to prevent fire and explosion.
1.Remove fuel pump relay module.
See
Multiport Fuel Injection Relays
2.Start and run engine.
3.When sufficient fuel has been used to cause fuel
line pressure to drop, injectors will become
inoperative, resulting in engine stall. Switch off
ignition.
4.Disconnect battery negative lead.
NOTE: Fuel at low pressure will remain in
system. To remove low pressure fuel,
place absorbent cloth around fuel feed
hose at fuel rail.
5.Disconnect either:
a) Nut and olive at fuel rail
OR
b) Hose at inlet end of fuel filter.
Refit
6.Refit fuel feed hose.
7.Refit fuel pump relay module, reconnect battery.
8.Crank engine (engine will fire in approximately 6
to 8 seconds).

MFI
7
REPAIR FUEL PRESSURE REGULATOR
Service repair no - 19.45.06
Remove
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Disconnect battery negative lead.
3.Remove plenum chamber.
See Plenum
Chamber
4.Release clip and disconnect fuel return hose
from regulator.
5.Disconnect vacuum hose from regulator.
6.Remove 2 bolts securing pressure regulator to
fuel rail.
7.Release regulator from fuel rail and withdraw.
8.Remove and discard 'O' ring.
Refit
9.Lightly coat 'O' ring with silicon grease 300 and
fit to regulator.
10.Reverse removal procedure.
11.Reconnect battery and pressurise fuel system.
Check there are no fuel leaks around regulator
connections.FUEL RAIL-INJECTORS R/H AND L/H
Service repair no - 19.60.04 - Rail
Service repair no - 19.60.01 - Injectors
Remove
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Disconnect battery negative lead.
3.Remove plenum chamber.
See Plenum
Chamber
4.Remove ram housing.See Ram Housing
NOTE: Place cloth over ram tube openings
to prevent ingress of dirt.
5.Loosen clip and disconnect fuel return hose from
regulator.
6.Loosen union and disconnect fuel supply hose
from fuel rail.
7.Disconnect multi-plug from fuel temperature
sensor.
8.Disconnect multi-plugs from injectors.
9.Remove four bolts securing fuel rail support
brackets to intake manifold. Lay injector
harnesses to one side.

19FUEL SYSTEM
8
REPAIR 10.Remove fuel rail and injectors.
11.Remove injector retaining clips, ease injectors
from rail. Remove and discard 'O' rings from
injectors.
12.Remove fuel pressure regulator if required.
Refit
13.FitNEW'O' rings, to injectors. Lightly coat 'O'
rings with silicon grease 300. Insert injectors into
fuel rail, multi-plug connections facing outwards.
14.Refit retaining clips.
CAUTION: Care must be taken when
refitting the fuel rail and injectors to intake
manifold to prevent damage to 'O' rings.
15.Fit aNEW'O' ring to pressure regulator lightly
coat 'O' ring with silicon grease 300 and secure
regulator to the fuel rail.
16.Fit fuel rail and heater pipe assemblies to intake
manifold. Secure rail and pipes in position with
five bolts.
17.Reverse removal procedure. 2 to 7.
18.Pressurise fuel system and check for fuel leaks
around injectors and pressure regulator.PLENUM CHAMBER
Service repair no - 19.22.46
Includes throttle levers and throttle disc
Remove
1.Disconnect battery negative lead.
2.Disconnect electrical multi-plug from bypass air
valve.
3.Disconnect vacuum hose adjacent to bypass air
valve.
4.Mark an identification line on throttle cable outer
to assist re-assembly.
5.Remove clevis pin from throttle cable.
6.Pry adjustment thumb wheel from throttle
bracket. Lay cable aside.
7.Remove retaining clip and clevis pin from kick
down cable (automatic vehicles).
8.Apply adhesive tape behind rear adjustment nut
on kick down cable to prevent nut moving.
9.Remove front lock nut. Remove cable and lay
aside.
10.Remove cruise control vacuum hose.
11.Remove intake hose from neck of plenum
chamber.
12.Disconnect throttle position sensor multi-plug.
13.Remove PCV breather hose.
14.Disconnect two coolant hoses and plug each
hose to prevent excessive loss of coolant.
Identify each hose for re-assembly.

19FUEL SYSTEM
14
REPAIR RAM HOUSING
Service repair no - 19.70.04
Remove
1.Disconnect battery negative lead.
2.Remove plenum chamber.
See Plenum
Chamber
3.Release hoses from ram housing.
4.Remove six through bolts (with plain washers)
securing ram housing to intake manifold.
5.Remove ram housing from intake manifold.
6.Place a protective cover over inlet bores to
prevent ingress of dirt.
Refit
7.Clean all mating faces.
8.Apply 'Hylomar' sealant to intake manifold face.
9.Fit ram housing. Tighten bolts, working from two
centre bolts, diagonally towards outer four bolts.
10.Tighten to
26 Nm.
INTAKE MANIFOLD
Service repair no - 30.15.08
Remove
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Disconnect battery negative lead.
3.Drain cooling system.
See COOLING SYSTEM,
Repair, Radiator
4.Remove plenum chamber.See Plenum
chamber
5.Remove ram housing.See Ram Housing
CAUTION: Place a protective cover over
intake manifold openings to prevent the
ingress of dirt.
6.Disconnect the fuel temperature sensor and
injector multiplugs.
7.Remove fuel pressure regulator.
See Fuel
Pressure Regulator
8.Disconnect multiplug from coolant temperature
sensor.
9.Disconnect instrument pack temperature
thermistor.
10.Disconnect coolant sensor multiplug.

MFI
17
REPAIR FUEL FILTER
Service repair no - 19.25.02
Remove
WARNING: Spilling of fuel is unavoidable
during this operation. Ensure all
necessary precautions are taken to
prevent fire and explosion.
WARNING: Ensure fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out following instructions.
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Access to filter is gained through right hand rear
wheel arch.
3.Clean area around hose connections to prevent
ingress of foreign matter into fuel system. Clamp
inlet and outlet hoses to prevent fuel spillage
when disconnecting hoses.
4.Loosen two fuel line unions and remove hoses.
Plug ends of hoses to prevent ingress of dirt.
5.Release securing bolt and bracket and remove
filter from chassis side member.
Refit
6.Fit a new filter observing direction of flow arrows
stamped on canister.
7.Tighten securing nut and bolt.
8.Fit inlet and outlet hoses. Tighten to
30Nm.
9.Refit fuel pump relay module, reconnect battery.
10.Start engine and inspect for fuel leaks around
hose connections.

19FUEL SYSTEM
20
REPAIR ACCELERATOR PEDAL
Service repair no - 18.30.35
Remove
1.Remove lower dash panel.
2.Remove clevis pin securing throttle cable to
accelerator pedal.
3.Release tension from pedal return spring.
4.Remove circlip from pedal pivot pin.
5.Withdraw pivot pin.
NOTE: It may be necessary to lower
steering column to gain access to pivot
pin circlip.
6.Remove accelerator pedal.
Refit
7.Lightly grease pivot and clevis pins.
8.Fit clevis pin using aNEWcotter pin.
9.Reverse removal procedure.FUEL PUMP AND SENDER UNIT
Service repair no - 19.45.03
A plastic fuel tank with a combined fuel pump/sender
unit is fitted. The fuel pump/sender unit is accessed
through a panel in the load space floor.
Fuel pump/sender unit
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Service Tools:
LRT-19-001 wrench - pump retaining ring
LRT-19-002 'Speedfit' disconnector
Remove
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Disconnect battery negative lead.
3.Syphon at least 9 litres (2 gallons) of fuel from
fuel tank into a suitable container that can be
sealed.
4.Remove carpet from loadspace floor and
tailgate.
5.Fold back loadspace sound insulation to reveal
access panel.