1995 LAND ROVER DISCOVERY ECU

76CHASSIS AND BODY
66
REPAIR
15.Release LH and RH, 'A' post trim finishers from
uppermost retaining clips.
16.With assistance, release headlining from LH and
RH, 'A', 'B' and 'D' post finishers.
17.Remove headlining assembly.Dismantle
18.Remove 22 nuts securing headlining stowage
nets and rear headlining panel.
19.Remove stowage nets and headlining panel.
20.Collect 7 mounting plates.
Rebuild
21.Position stowage nets and headlining panel, fit
mounting plates to studs and secure with nuts.
Refit
22.With assistance, fit headlining and position to LH
and RH, 'A', 'B' and 'D' post finishers.
23.Secure LH and RH, 'A' post trim finisher
retaining clips.
24.Fit rear sun roof aperture seal.
25.Fit and tighten screw securing rear headlining
panel to body.
26.Position vents to headlining, attach clips to vents
and secure to headlining.
27.Position rear sun roof switch, connect multiplug
and secure to headlining panel.
28.Position rear passenger interior lamp, connect
multiplug and secure to headlining panel.
29.Fit front sun roof aperture seal.
30.Fit LH and RH sun visor retaining clips to body.
31.Fit and tighten screws securing sun visor
retaining clips and secure screw covers.
32.Fit RH alpine light trim casing.
See alpine light
trim casing.
33.Fit LH alpine light trim casing.See alpine light
trim casing - lh - with rear air conditioning
fitted.
34.Fit front headlining stowage panel.See
headlining stowage panel - front - with sun
roof fitted.
35.Fit grab handles.See grab handle.
36.Fit sun visors.See sun visor.

CHASSIS AND BODY
67
REPAIR ASH TRAY - DASH PANEL CENTRAL LOUVRE
PANEL
Service repair no - 76.67.26
Remove
1.Open ash tray.
2.Press release catch and remove ash tray.
Refit
3.Fit ash tray.HEADLINING STOWAGE PANEL - FRONT - WITH
SUN ROOF FITTED
Service repair no - 76.67.27
Remove
1.Remove 10 screws securing stowage panel to
body.
2.Release panel and disconnect Lucar and 4
multiplugs.
3.Remove stowage panel assembly.

76CHASSIS AND BODY
68
REPAIR Dismantle
4.Remove interior lamp lens.
5.Remove 2 nuts securing lamp to stowage panel.
6.Remove lamp.
7.Remove alarm volumetric sensor/blanking plate.
8.Remove electric sun roof switch pack.
9.Remove electric sun roof manual opening plug.
Rebuild
10.Fit electric sun roof manual opening plug to
panel.
11.Fit alarm volumetric sensor.
12.Fit electric sun roof switch pack to panel.
13.Fit interior lamp to panel and secure with nuts.
14.Fit interior lamp lens.
Refit
15.Position stowage panel assembly and connect
Lucar and multiplugs.
16.Align panel to headlining and secure with
screws.REAR FOLD DOWN SEAT BELTS - LH WITH REAR
AIR CONDITIONING FITTED
Service repair no - 76.73.28/20
Remove
1.Locate the seat in the down position, remove the
seat belt strap and buckle from their stowed
positions.
2.Remove seat belt strap and buckle retaining bolt
covers.
3.Remove bolts securing strap and buckle.
4.Remove seat belts and collect spacers.
Refit
5.Fit spacers to seat belt retaining bolts, position to
fixings and tighten to
32 Nm (24 lbf ft).
6.Fit seat belt retaining bolt covers.
7.Secure seat belt strap and buckle to their stowed
positions and position seat in the up position.

CHASSIS AND BODY
69
REPAIR FRONT SEAT BELTS - 5 DOOR (96 MODELS)
Service repair no - 76.73.10
Remove
1.Move the seat to gain access to the seat belt
mountings.
2.Remove the cover and securing bolt to release
the upper mounting and spacer from the 'B' post
adjustable mounting.
3. Electric seats only:Release fixings securing
the seat side valance.
4.Remove the side valance.
5.Remove the Torx bolt securing the lower
mounting to the seat.
6.Detach the door seals from the 'B' post
sufficiently to allow removal of the lower trim
panel from the post.
7.Release the seat belt from the split section at the
top of the trim panel and withdraw the panel.

76CHASSIS AND BODY
70
REPAIR
8.Remove the securing bolt and detach the inertia
reel from the bottom of the 'B' post.9.Release the seat belt sensor connector (if fitted).
10.Release Torx bolt to allow removal of the seat
belt stalk assembly.
Refit
11.Reverse removal procedure.
NOTE: Ensure the seat belt is not twisted.
12.Re-connect the seat belt sensor connector (if
fitted).
13.Finally, tighten the seat belt fixings to
32 Nm (24
lbf ft)
.

HEATING AND VENTILATION
3
REPAIR Air direction
3.Set control fully clockwise
4.Release outer cable from 2 clips on unit.
5.Release cable from stud on flap lever.
6.Remove control cable from control lever.
Temperature
7.Set RH control fully clockwise, LH control fully
anti-clockwise
8.Release outer cable from 2 clips on unit.
9.Release cable from stud on flap lever.
10.Remove control cable from control lever.
Refit
11.Reverse removal procedure. Check the
satisfactory function of the controls before fitting
louvre vent panel.RESISTOR UNIT
Service repair no - 80.20.17
Remove
1.Open glove box, manoeuvre side springs
through cut-outs and lower lid.
2.Remove 2 screws securing resistor unit to
trunking.
3.Disconnect multiplug and remove resistor unit.
Refit
4.Reverse removal procedure.

80HEATING AND VENTILATION
4
REPAIR WATER VALVE
Service repair no - 80.10.16
Remove
1.Disconnect vacuum pipe from water valve.
2.Slacken 4 clips securing hoses to water valve.
3.Use a thin blade to break seal between hoses
and nozzles
4.Disconnect heater inlet hose from valve.
NOTE: A quantity of coolant will be
released.
5.Disconnect heater outlet hose from valve.
6.Lever valve from coolant pipe hoses.
Refit
7.Reverse removal procedure. Lightly lubricate
water valve nozzles with petroleum jelly.
8.Reverse removal procedure. Top-up engine
coolantVACUUM SWITCH - WATER VALVE
Service repair no - 80.10.36
Remove
1.Release emission pipe from retaining clip.
2.Remove bolt securing switch to bulkhead.
3.Disconnect multiplug from switch.
4.Disconnect 2 vacuum pipes and remove vacuum
switch.
Refit
5.Reverse removal procedure.

HEATING AND VENTILATION
5
REPAIR RECIRCULATION SWITCH
Service repair no - 80.10.27
Remove
1.Release fascia centre louvre vent panel from its
fitted position to gain access to rear of panel.
See CHASSIS AND BODY, Repair, Dash
Panel Central Louvre Panel
2.Disconnect multiplug from switch
3.From the rear, push switch out of panel.
Refit
4.Reverse removal procedure.RECIRCULATION FLAP SOLENOID
Service repair no - 80.10.43
Remove
1.Open glove box, manoeuvre side springs
through cut-outs and lower lid.
2.Remove 2 locknuts securing cruise control ECU
to bracket.
3.Position cruise control ECU aside.
4.Remove 2 screws securing recirculation
solenoid to casing.
5.Release solenoid from lever.
6.Disconnect multiplug and remove solenoid.
Refit
7.Reverse removal procedure.